Sanyo PDP-32H1EV User manual

Multimedia Plasma Monitor
SERVICE MANUAL
FILE NO.
Model No. PDP-32H1EV
(EUROPE)
PDP32H1A
(U.S.A., ASIA)
ORIGINAL VERSION
PRODUCT CODE
1 114 016 00 PDP-32H1EV, J3DH
1 114 035 00 PDP-32H1A, J3DFB
REFERENCE NO. SM5110287-00
Chassis No. PDP-32H1E-00
(PDP-32H1EV)
NOTE: Match the Chassis No. on the
unit’s back cover with the Chassis
No. in the Service Manual.
If the Original Version Service
Manual Chassis No. does not
match the unit’s, additional
Service Literature is required. You
must refer to “Notices” to the
Original Service Manual prior to
servicing the unit.
CONTENTS
Pages
SAFETY INSTRUCTIONS --------------------------------------------------------------------- 2
TECHNICAL SPECIFICATIONS ------------------------------------------------------------- 3
DIMENSIONS AND OPTIONS---------------------------------------------------------------- 4
TERMINALS FOR PC----------------------------------------------------------------------- 5 - 6
MECHANICAL DISASSEMBLIES------------------------------------------------------ 7 - 16
ADJUSTMENT ---------------------------------------------------------------------------- 17 - 21
CIRCUIT BLOCK DIAGRAM----------------------------------------------------------- 22 - 23
POWER SUPPLY LINES --------------------------------------------------------------------- 24
POWER FAIL CIRCUIT ----------------------------------------------------------------- 25 - 26
TROUBLESHOOTING ------------------------------------------------------------------ 27 - 28
CONTROL PORT FUNCTIONS ------------------------------------------------------ 29 - 30
IC BLOCK DIAGRAMS------------------------------------------------------------------ 31 - 38
PIN DESCRIPTION OF DIODE, TRANSISTOR AND IC----------------------------- 39
PARTS LIST ------------------------------------------------------------------------------- 40 - 61
PARTS DESCRIPTION AND READING IN SCHEMATIC DIAGRAM ------------ 62
SCHEMATIC DIAGRAMS---------------------------------------------------------- A-1 - A-18
PRINTED WIRING BOARD DIAGRAMS ------------------------------------- A-19 - A-30
Chassis No. J3D-32H1A00
(PDP-32H1A)
Speaker Unit and Stand
are not included.

-2-
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
●This Plasma Monitor should be set in the way indicated. If not, it may result in a fire hazard.
●Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and
cooling the Plasma Monitor. Minimum distance should be taken. If the Plasma Monitor is to be built into a
compartment or similarly enclosed, the minimum distances must
be maintained. Do not cover the ventilation slot on the Plasma
Monitor. Heat build-up can reduce the life of your Plasma
Monitor, and can also be dangerous.
●If the Plasma Monitor is not to be used for an extended time,
unplug the Plasma Monitor from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
SIDE and TOP REAR
CAUTION IN INSTALLING
●Handle the Plasma Monitor carefully when installing it and do not drop.
●Locate set away from heat, excessive dust, and direct sunlight.
●For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to
follow correct mounting procedures could result in damage to the equipment or injury to the installer.
10 cm
10 cm
10 cm
6 cm
NOTE :
When Plasma Monitor is not used for a long period of time, unlighting dots may be observed. This is caused by
characteristic of the Plasma Monitor. If this occurs, turn the Plasma Monitor on and leave it on about 1 hour. These
dots will gradually disappear.
■Safety Instructions
Product safety should be considered when a component replacement is made in any area of the monitor.
Components indicated by mark in the parts list and the schematic diagram designate components in
which safety can be of special significance. It is, therefore, particularly recommended that the replacement of
there parts must be made by exactly the same parts.
PRODUCT SAFETY NOTICE

-3-
■Technical Specifications
Screen Diagonal 32V
Product name Multimedia Plasma Monitor
Panel type Plasma Display Panel (16 x 9)
Display area 716 mm (W) x 399 mm (H)
Resolution / Color 852 x 1024 pixels / 16,770,000 colors
Viewing Angle 160˚(Vertical / Horizontal)
Color System PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
PC Interface D-SUB, RGB
Capability Up to XGA
Plug & Play VESA DDC2B
Power Management VESA DPMS
Audio Amp 8W + 8W (8 Ω)
Terminals
AC IN 3PIN
VIDEO1 IN ✽VIDEO / S-VIDEO (RCA type / Mini DIN 4pin type)
AUDIO R and L (MONO) (RCA type)
VIDEO2 IN ✽VIDEO / S-VIDEO (BNC type / Mini DIN 4pin type)
AUDIO R and L (RCA type)
COMPONENT/RGB IN ✽R, G, B, VD, HD / Y, Pb/Cb, Pr/Cr (BNC type)
AUDIO R and L (RCA type)
PC IN RGB (D-SUB 15pin)
AUDIO R / L (Stereo Mini jack)
RS232C IN RS232C (D-SUB 9pin)
WIRED RC IN Stereo Mini Jack
MONITOR OUT ✽VIDEO (RCA type)
AUDIO R and L (RCA type)
HEADPHONE OUT Stereo Mini Jack
EXT. SP OUT R and L, 8W (8 Ω), Push type
POWER SUPPLY AC 220 - 240V 50/60 Hz (PDP-32H1EV, PDP-32H1E)
AC 100 - 240V 50/60 Hz (PDP-32H1A)
DIMENSION (W x H x D) 829 x 517 x 122 mm (32.6" x 20.4" x 4.8" ) (Plasma Monitor only)
WEIGHT (NET) 25 kg (55.1 lbs ) (Plasma Monitor only)
Power Consumption 240 W
Regulations FCC CLASS-B, UL, CE
Environmental Considerations
Operating Temperature 0˚C ~ 40˚C (32˚F ~ 104˚F )
Humidity 20 ~ 80%
Altitude 0 ~ 2,000 m (0 ~ 6,560 ft)
Storage Temperature -10˚C ~ 50˚C (14˚F ~ 122˚F)
Humidity 20 ~ 80 %
Altitude 0 ~ 3,000 m (0 ~ 9,840 ft)
Accessories Owner’s Manual
AC Power Cord
Wired/Wireless Remote Control Transmitter and Batteries
PC Cable (D-SUB)
Remote Control Cable
BNC / RCA Adapter ( x4)
Ferrite core
✽ Those terminals are not provided on model PDP-32H1E.
●Specifications are subject to change without notice.

-4-
829
(32.6)
829
(32.6)
517
(20.4)
122
(4.8)
101
(4.0)
Size in mm (inch)
The products listed below are optionally supplied.
When ordering these products, give name and Type No. to sales dealer.
OPTIONS
Speaker unit KA-SX-32H (R and L)
Table top stand KA-TD-H10S
Floor stand KA-TD-H10W
Side rack KA-TD-R100
Tilt mount unit KA-TI-H10
Wall mount unit KA-WA-H10WV
Ceiling mount unit KA-CH-H10
MEASUREMENT
■Dimensions and Options
MEASUREMENT
OPTIONS

-5-
RS232C TERMINAL
Terminal : HDB9-PIN
Connect the serial port of computer to this terminal with Serial Cross Cable (not supplied).
3
5
4
2
1
7
9
8
6
No Connect
Ground
R x D
DTR (5V)
T x D
1
5
2
4
3
DSR
No Connect
No Connect
No Connect
6
7
9
8
Pin Configuration
CONFIGURATIONS OF RS232C TERMINALS
RS232C COMMAND
(ASCII)
C09
C03
C01
C00
C0A
C0B
C22
C23
C0F
C24
C10
C25
C26
C27
C28
C29
C5F
C30
C47
C46
C60
OPERATION
VOLUME UP
POWER ON-OFF
POWER OFF
POWER ON
VOLUME DOWN
MUTE
INPUT (Input signal select)
INPUT "VIDEO" (VIDEO1 / VIDEO2)
Wide mode "Normal"
INPUT "COMPONENT" (COMPONENT)
WIDE (Wide mode select)
INPUT "PC / RGB" (PC / RGB)
Wide mode "Natural wide"
Wide mode "Zoom"
Wide mode "Zoom (Caption-IN)"
Wide mode "Full"
Screen Saver "White pattern-On"
PICTURE
Screen Saver "Rotation-Off"
Screen Saver "Rotation-On"
Screen Saver "White pattern-Off"
COMMAND
HEX
ASCII
43h 30h 30h 0Dh 0Ah
'C' '0' '0' [CR] [LF]
EXAMPLE : POWER ON (C00) FUNCTION CODE / END CODE
INTERFACE Protocol
Stop bit
Boadrate
Parity
Data length
Flow control
RS-232C
2 bits
9600 bps
-
8 bits
-
■Ter minals for PC

-6-
CONFIGURATIONS OF PC TERMINALS
PC IN (D-SUB) TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of computer to this terminal with VGA Cable (supplied). When connecting the Macintosh
computer, the MAC Adapter (not supplied) is required.
51
2
34
10
9 678
15 14 13 11
12
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
No Connect
Horiz. sync.
Ground (Vert.sync.)
Sense 1
Sense 0
Vert. sync.
Reserved
9
13
10
12
11
14
15
Pin Configuration
MAC ADAPTER (NOT SUPPLIED)
Set Slide Switches as shown in the table below depending on RESOLUTION MODE that you want to use before
you turn-on Plasma Monitor and computer.
ON
1
DIP
ON
OFF
2 3 4 5 6
13” MODE (640 x 480)
16” MODE (832 x 624)
19” MODE (1024 x 768)
21” MODE (1152 x 870)
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1 2 3 4 5 6
Slide Switches (1 ~ 6)
Terminals for PC

-7-
■Mechanical Disassemblies
■Optional Stand Removal
1.Put the PDP Monitor Display with the screen face down
on the flat desk.
CAUTION : When placing the display with the face down,
lay the soft cloth under the screen to protect
the screen surface. And make sure there is
nothing to damage the screen surface like a
screw or small part near by before placing the
display.
2.Remove 6 Screws (A). (Fig. 1)
■Optional Speaker Removal
Fig. 2
Fig. 1
A
1.Remove speaker lead wires (R & L).
2.Remove 16 Screws (B) and 4 plates. (Fig. 2)
B
1. Cabinet Back Removal (Fig. 3)
Remove screws (A,B,C) and remove Cabinet Back as Fig. 3.
A (14pcs: 4X8), B (10pcs: 5X8), C (2pcs: 3X8)
AAAA
AAAA
A
A
A
A
A
A
B
B
B
B
B
B
BB
B
B
CC
Fig. 3

-8-
Cjbg
ZT[A
jbg
ZT[B
jbg
d„XCb‘
jbg
RC&LED
jbg RlNgjbg
^[~iAjbg
^[~iBjbg
d„jbg
„”‘[i[
jbg
pt@pt@
LrlbgO
g
Fig. 4
Location of Circuit Board and Others
Audio Unit
FAN
Main Unit
FAN
Power Unit
Cabinet Front
Sensor Unit (A)
Power SW
Unit
RC & LED
Unit
Connect Unit
Terminal A Unit
Terminal B Unit
Mechanical Disassemblies

-9-
2. Panel Module and Chassis Removal (Fig. 5)
1) Remove 16 screws (D: 4X8). (Fig. 5)
2) Remove Flat Cable from Button Unit (Position + / -, Volume + / - ...etc.) to Audio Unit (K8X).
3) Remove chassis with Panel Module to have Panel Holder and lift up.
4) Place chassis with the face down to the desk with soft cloth.
[ATTENTION]
As R/C Pre-AMP is projected from surface of panel, it is necessary to place out of desk.
plz_[
RlN^
K8X
R
vAv
LrlbgOg
DD
D
DDDD DDDD
DD
DDD
Fig. 5
[ATTENTION]
This PDP monitor is used the different kind of screw. Using correct screwis needed to avoid the damage.
Panel Holder Cabinet Front
R/C Pre-AMP
[ATTENTION]
Connector
K8X
Panel
Desk
Mechanical Disassemblies

-10-
E E
F
pt@ pt@
G
G
G
G
F
plz_[
3. Chassis Removal (Fig. 6)
To remove chassis from Panel Module.
1) Remove screws (E & F) and remove FANs with holder plate from chassis.
2) Remove screws (G) and remove Panel Holder and Spacer (between holder and module) from chassis.
E (2pcs: 4X8 + 2 washers), F (2pcs: 3X6), G (4pcs: 5X40)
Fig. 6
Panel Holder
FANFAN
Mechanical Disassemblies

-11-
HHH HHH I
II
I
HHH HHH
Cjbg
RlN^
K7SAK3ST
d„jbg
RlN^KPOW2 A
K6UAKPOW 3
ZT[jbgA
RlN^KS EN S1
'˛R[h2{
˘˜¢ØXN[
„”‘[i[
j
b
g
Zp
lW
Zp
lW
3) Slightly lift up the chassis from Panel Module after removing screws (H & I ) and 2 hexagonal screws.
4) In the condition of item 3), remove lead wire from Main Unit (K7S,K3ST) to Panel Module. (Panel Module
Side).
5) Remove screw fixed 2 yellow-green lead wire (ground) from AC power connector and Panel Module. (Fig.7)
6) In the condition of item 3), remove lead wire from Audio Unit (K16Y) to Panel Module. (Panel Module Side).
7) Remove connector of Power Unit (KPOW2, K6U,KPOW3) and Sensor Unit A (KSENS1)
8) To lift up chassis, remove from Panel Module.
H (14pcs: 6X12), I (4pcs: 5X8)
Power Unit
Connector
KPOW2,K6U,KPOW3
Main Unit
Connector
K7S,K3ST
Sensor Unit (A)
Connector
KSENS1
Audio Unit
Connector
K16Y
Screw for Fixing
Yellow-Green
Wires
Hexagonal
Screw
Hexagonal
Screw
Mechanical Disassemblies
H
H
Fig. 7

-12-
d„jbg
ZT[Ajbg
J
KKK
J
Zp
lW
Zp
lW
Fig. 8
9) Remove screws (J & K), and remove Power Unit and Sensor Unit (A) with holder plate from Panel
Module. Note: Fix screws (K) to Panel Module after removing these units.
10) Remove 2 hexagonal screws to be only Panel Module.
J (2pcs: 3X8), I (3pcs)
Hexagonal
Screw
Hexagonal
Screw
Sensor Unit (A)
Power Unit
Mechanical Disassemblies
[NOTE]
Can not clean after assembling Panel Module, if caught dust to Panel surface or Optical Filter.

-13-
4. Optical Filter Removal
Cabinet Front includes Optical Filter to protect the
damage of Panel, improve picture quality, or pre-
vent exposure of interference.
For removal of Optical Filter, remove screws of
Fig.9.
[NOTE]
1. The Optical Filter is easy to be damaged. Do
not touch directly by hand. If there is dust,
remove it by watery neutral detergent.
2. The gasket (like brown tape) is sticked on the
Optical Filter. Order Optical Filter with gaskets
for service parts. Refer to parts list.
5. Servicing of Unit (Refer to Fig.4)
For removal of Main or Audio Unit, remove screws fixed to chassis plate.
In case of Audio Unit, remove shield plate covered with Line Filters (LF1601, LF1602, LF1603).
Note : The shield plate is soldered at left side of circuit board.
6. Servicing of Back Terminal
For removal of Connect Unit, remove 25 screws (L: 3X6) of Fig.10.
Note : Terminal Unit (A, B) is connected to Connect Unit.
Fig. 9
■ PDP Panel Replacement
For change of PDP Panel (Module), proceed 1to 3.
Mechanical Disassemblies
L
L
L
L
Fig. 10
Gasket

-14-
■Flat Cable Removal
This set is used 3 kinds of connector for flat cable. For removal of cable, refer as below not to damage.
■For Gasket
The gasket (like brown tape) is provided to prevent exposure of interference for other radio and television receptions.
The gasket should be replaced on previous positions after servicing.
See Fig.9 for example.
For removal of flat cable, slide hook of
both sides.
For insert and fixing, slide hook to pre-
vious position after inserting the flat
cable.
Type A Type B Type C
For removal of flat cable, lift up hook of
both sides.
For insert and fixing, hold down hook
after inserting the flat cable.
For removal of flat cable, pull off only.
For fixing , insert into socket.
Cable Cable Cable
Mechanical Disassemblies

-15-
■ Notice for service of Unit
In below Unit, can be repaired inside parts or unit itself. Order service parts for repair.
Cjbg
ZT[A
jbg
ZT[B
jbg
d„XCb‘
jbg
RC&LED
jbg RlNgjbg
^[~iAjbg
^[~iBjbg
d„jbg
„”‘[i[
jbg
pt@pt@
LrlbgO
g
Power Unit
Sensor A
Unit
Audio Unit
Main Unit
RC&LED
Unit
Power
Switch
Unit
Connect Unit
Terminal A Unit
Terminal B Unit
Mechanical Disassemblies

-16-
d„jbg
ZT[Ajbg
J
KKK
J
Zp
lW
Zp
lW
Mechanical Disassemblies
Do not remove Panel only.
For changing Panel, it is necessary to change
these all units too.
Refer to parts list.
Attention
Below 4 Units are included with Panel for PDP Module. Do not remove from Panel.
For changing Panel, it is necessary to change these all units too.
Can not order unit itself.
!

-17-
■Adjustment
Before Adjustment
This adjustment is done to enter Service Mode by Remote
Control Unit.
■ To enter Service Mode
Quick operation is needed to enter Service Mode.
(1) Turn the monitor on.
(2) Press and hold the MENU button on the monitor.
(3) Keep item (2) and press the STATUS button and
release the both buttons.
(4) Within 2 seconds after item (3), press the MUTE
button to appear the Service Mode Display.
■ Service Mode Display
■ To return to the Normal Mode
Once turn the Monitor off by pressing “POWER” button on the monitor or remote control unit and turn it on again.
MENU
OK
INPUT VOLUME
MENU Button
MUTE
WIDE
INPUT
ON-OFF
VOLUME
PC/RGB
F
COMPONENT
OFF TIMER
PICTURE
STATUS
MOVE UP
MOVE DOWN
VIDEO
OK
OFF
ON
POWER
MENU
(←) / (→)
To select :
Adjustment Item
or Data Setting
To enter
Service Mode
STATUS
MUTE
(↑)
●Adjustment :
UP
●Data Setting
(+)
(↓)
●Adjustment :
DOWN
●Data Setting
(–)
Av-Dynamic
Cont063 (3F)
Main
Sub
32H1
103
040
CAUTION
The each circuit has been made by the fine adjustment at factory. Do not attempt to adjust
the following adjustments except requiring the readjustments in servicing otherwise it may
cause loss of performance and product safety.

-18-
■ To adjust
The next 2 pages show Data for adjustment.
To select adjustment item, press (↑) button on the remote control unit.
To adjust data, press (→) button ( The characters of data become yellow.) and press (↑) or (↓) button to
change data.
The all data adjusted in service mode memorizes into non-volatile memory IC.
Note: In the explanation all buttons are indicated for remote control unit without any notice.
Service Mode Display
Av-Dynamic
1) Select adjustment item by (↑) but-
ton.
Adjustment item displays in order. To reverse
adjustment item, press (↓) button.
3) Adjust the data by (↑) (↓) button.
To adjust another item, press (←) button to
change color of characters of adjustment item
and repeat 1) to 3).
Select by (↑) Button
and
Press (→) Button ( )
Hex decimal data
Adjust by (↑) or
(↓) Button.
4) To exit the Service Mode.
To exit the service mode, press POWER ON-
OFF button on the monitor or remote control
unit.
2) Press (→) button to change color
of characters (of data).
The character of data become yellow by pressing
(→) button.
0Cont 63 (3F)
Adjustment Item Data
Number
Av-Dynamic
Cont063 (3F)
Main
Sub
32H1
103
040
Adjustment

-19-
0AV-Dynamic Contrast 63 0 63 Picture Menu (Dynamic)
1Brightness 31 0 63
2Color 52 0 63
3Tint 0 -31 32
4Sharpness 19 0 30
5AV Standard Contrast 50 0 63 Picture Menu (Natural)
6Brightness 31 0 63
7Color 38 0 63
8Tint 0 -31 32
9Sharpness 15 0 30
10 AV Cinema Contrast 37 0 63 Picture Menu (Cinema)
11 Brightness 32 0 63
12 Color 35 0 63
13 Tint 0 -31 32
14 Sharpness 13 0 30
15 PC Graphic Contrast 63 0 63 Picture Menu (Graphic)
16 Brightness 31 0 63
17 Color 45 0 63
18 Tint 0 -31 32
19 --------------- -- -- --
20 PC Standard Contrast 40 0 63 Picture Menu (Standard)
21 Brightness 31 0 63
22 Color 31 0 63
23 Tint 0 -31 32
24 --------------- -- -- --
25 PC-Text Contrast 31 0 63 Picture Menu (Text)
26 Brightness 31 0 63
27 Color 26 0 63
28 Tint 0 -31 32
29 --------------- -- -- --
30 Sub Menu AV Contrast 60h 00h FFh Composite, S-Video
31 Brightness 37h 00h FFh
32 Color-S 78h 00h FFh S-Video
33 --------------- -- -- --
34 Tint FFh 80h 7Fh
35 Sharpness 0Fh 00h 1Fh 0Fh=9415add.5Dh:78h
36 Sub Menu PC Contrast 60h 00h FFh
37 Brightness 39h 00h FFh
38 Color 80h 00h FFh
39 Tint 00h 80h 7Fh
40 Sharpness 40h 00h FFh
41 Sub Menu AV-D2-D4 Contrast 5Bh 00h FFh D2–4 Input
42 Brightness 40h 00h FFh
43 Color 80h 00h FFh
44 Tint FAh 80h 7Fh
45 Sharpness 40h 00h FFh
46 Sub Menu AV-D1 Contrast 60h 00h FFh D1 Input (480i)
47 Brightness 40h 00h FFh
48 Color C0h 00h FFh
49 Tint 00h 80h 7Fh
50 Sharpness 0Ch 00h 1Fh 0Fh=9415add.5Dh:78h
51 Color Temp H-AV Red DCh 00h FFh AV Color Temperature (High)
52 Green F0h 00h FFh
53 Blue FFh 00h FFh
54 Color Temp M-AV Red FFh 00h FFh AV Color Temperature (STD)
55 Green FFh 00h FFh
■ Service Adjustment Data Table
Adjustment
• All data except in gray box area is fixed. Do not change for correct operating.
• Data in gray box area is initial. Can be set according to adjustment information.
No. NoteAdjustment Name
Data Area
Adjustment Item Initial
Data Min Max

-20-
56 Blue FFh 00h FFh
57 Color Temp L-AV Red FFh 00h FFh AV Color Temperature (Low)
58 Green EBh 00h FFh
59 Blue CDh 00h FFh
60 Color Temp H-PC Red DCh 00h FFh PC Color Temperature (High)
61 Green F0h 00h FFh
62 Blue FFh 00h FFh
63 Color Temp M-PC Red FFh 00h FFh PC Color Temperature (STD)
64 Green FFh 00h FFh
65 Blue FFh 00h FFh
66 Color Temp L-PC Red FFh 00h FFh PC Color Temperature (Low)
67 Green EBh 00h FFh
68 Blue CDh 00h FFh
69 Cont AV Red FFh 00h FFh White Balance Adjustment
70 Green FFh 00h FFh
71 Blue FFh 00h FFh
72 Bright AV Red 80h 00h FFh Black Balance Adjustment
73 Green 80h 00h FFh
74 Blue 80h 00h FFh
75 Cont PC Red 00h 00h FFh W/B (Differential Data to AV)
76 Green 00h 00h FFh
77 Blue 00h 00h FFh
78 Bright PC Red 00h 00h FFh B/B (Differential Data to AV)
79 Green 00h 00h FFh
80 Blue 00h 00h FFh
81 Cont PC Red 00h 00h FFh W/B (Differential Data to AV)
82 Green 00h 00h FFh
83 Blue 00h 00h FFh
84 Bright PC Red 00h 00h FFh B/B (Differential Data to AV)
85 Green 00h 00h FFh
86 Blue 00h 00h FFh
87 Cont-AV-D1 Red FEh 00h FFh W/B (Differential Data to AV)
88 Green 05h 00h FFh
89 Blue 00h 00h FFh
90 Bright-AV-D1 Red 00h 00h FFh B/B (Differential Data to AV)
91 Green 00h 00h FFh
92 Blue 00h 00h FFh
93 Sharpness-AV50 Sharpness 10 0 – Filter
94 Sharpness-AV60 Sharpness 6 0 – Filter
95 Sharpness-PC Sharpness 0 0 – Filter
96 Sharpness-HD Sharpness 10 0 – Filter
97 Snd-Sep Snd Sep 3Fh 0 3Fh Sound Separation
98 AFC Tuning-TV ABh 21Ch 000h FFFh
99 ACh 218h 000h FFFh
100 AFC Tuning-Video50 ABh 21Ch 000h FFFh
101 ACh 21Ch 000h FFFh
102 AFC Tuning-Video60 ABh 21Ch 000h FFFh
103 ACh 21Ch 000h FFFh
104 AFC Tuning-Video BEh 06h 00h FFh
105 AFC Tuning-D1 ABh 298h 000h FFFh
106 ACh 5D1h 000h FFFh
107 AFC Tuning-525i ABh 298h 000h FFFh
108 ACh 5D1h 000h FFFh
109 Color System Auto Auto/NTSC only
110 Wide Squeeze Off Off/On
111 Display Language English English/Japanese
112 PDP COLOR8 PDP Internal Pattern Display (∆Key)
113 PDP WHITE PDP Internal Pattern Display (∆Key)
Adjustment
No. NoteAdjustment Name
Data Area
Adjustment Item Initial
Data Min Max