Sanyo CP32WF2 User manual

SERVICE MANUAL Colour Television
Specifications
Power Source . . . . . . . .AC220 - 240V, 50Hz.
Colour System . . . . . . .PAL, SECAM, NTSC4.43, NTSC
Television System . . . . .B/G, DK, I, L/L
Channel Coverage . . . .VHF: 0-11, 5A (Australia), 1-11 (New Zealand)
E2-E12, F2-F10, R1-R12
UHF: 28-69 (Australia), 21-69 (New Zealand)
CATV: S1-S41, X,Y, Z, B-Q
Aerial Input Impedance 75Ω
Ext.Terminals
AV1 (Rear): CENELEC Standard
Input (Composite video, RGB and Audio-L/R)
Output (TV-output with composite video and Audio-L/R)
AV2 (Rear): CENELEC Standard
Input (Composite video, RGB, S-VHS and Audio-L/R)
Output (Monitor output with composite video and Audio-L/R)
AV3 (Front): Phone jack (Composite video input and Audio-L/R input)
Headphone Jack: Mini Stereo Jack
Speaker . . . . . . . . . . 6 cm ✕12 cm ✕ 2 pcs.
Sound Output (Music). . . .12W + 12W
Dimensions . . . . . . . . . . 880 (W) ✕575 (H) ✕549 (D)mm
Weight . . . . . . . . . . . . . . .approx. 55 Kg
Specifications subject to change without notice
F8WZ/F8WY
FILE NO.
Model No. CP32WF2
(Australia/New Zealand)
Give complete “SERVICE REF. NO.” for parts
order or servicing.It is shown on the rating label
at the cabinet back of the unit.
This T.V. receiver will not work properly in
foreign countries where the television
transmission system and power source dif-
fer from the design specifications. Refer to
the specification table.
Product Code:111371219
REFERENCE NO. SM5110636
PP
+
-
Original Version
Chassis Series: EB7-A
Service Ref. No. CP32WF2-00
(Australia)
CP32WF2-50
(New Zealand)
- NOTE -
Service Ref. No. CP32WF2-50 is electrically the
same as Service Ref. No. CP32WF2-00.
The difference between Service Ref. No.
CP32WF2-00 and CP32WF2-50 is as follows:
1) Destination CP32WF2 -00...Australia
CP32WF2 -50...New Zealand

Contents
-2-
Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chassis Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IC Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
CPU Port Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Option Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Service Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Purity and Convergence Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 13-14
Mechanical Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Protection Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cabinet Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chassis Electrical Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-27
Voltages and Waveforms Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
Safety Notice
SAFETY PRECAUTIONS
1: An isolation transformer should be connected in the
power line between the receiver and the AC line
when a service is performed on the primary of the
converter transformer of the set.
2: Comply with all caution and safety-related notes pro-
vided on the cabinet back, inside the cabinet, on the
chassis or the picture tube.
3: When replacing a chassis in the cabinet, always be
certain that all the protective devices are installed
properly, such as, control knobs, adjustment covers
or shields, barriers, isolation resistor-capacitor net-
works etc.. Before returning any television to the
customer, the service technician must be sure that
it is completely safe to operate without danger of
electrical shock.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially con-
structed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be
the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X
- RADIATION.To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this ser-
vice manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, take
necessary corrective action.Carefully follow the instructions for + B1 volt power supply adjustment, and high volt-
age check to maintain the high voltage within the specified limits.
PRODUCT SAFETY NOTICE
Product safety should be considered when a component replacement is made in any area of a receiver.
Components indicated by mark in the parts list and the schematic diagram designate components in which
safety can be of special significance. It is particularly recommended that only parts designated on the parts list
in this manual be used for component replacement designated by mark . No deviations from resistance
wattage or voltage ratings may be made for replacement items designated by mark .

Q611
IC3451
NICAM/STEREO DECODER
78
55 56
57
58
61
68
75
76
79
80
71
51/53
39
47
33
23
22
21
20
27
26
14 13
12
IC801
CPU
1
4
33,34
53
54
11
21
20
19
8
17
16
15
18
45
IC201
IF /VIDEO/
CHROMA/
DEF.
BLK
R IN
G IN
B IN
33,34
47,48 36,37
31,32
451,52
12
5
60,61
IC001
AUDIO AMP.
8,10 1,5
3
AUDIO L & R
HEAPHONE JACK
& SWITCH
SPEAKER
SP901 SP902
A101
F/STUNER
AERIAL
SCL SDA
RF AGC
19
15
1,3
2,6
20
11
7
K1001 AV1 SCART 1
TV OUT
VIDEO OUT (TV)
CRT
FOCUS/SCREEN
R
B
G
V
L
R
K1101
AV3 IN (FRONT)
VIF IN
VIF IN SAW FILTER
(VIF)
X132
SIF IN
SIF IN SAW FILTER
(SIF)
X131
IC1201
VIDEO SW
8
9
6
4
1
AV1 VIDEO IN
RGB SW
IC1401
AV1 AUDIO IN
AUDIO IN (SCART 1)
AUDIO IN (SCART 2)
AUDIO OUT
1/3/13
AV2 (VIDEO orY IN)
AV3
(VIDEO IN)
AV3 AUDIO IN
R IN
G IN
B IN
R IN
G IN
B IN
C IN
VIDEO /Y OUT
VIDEO /Y IN
VIDEO MONITOR
OUT
AUDIO MONITOR OUT
AUDIO MONITOR OUT
(TO SCART 2)
(From pin-47 & 48 of IC3451)
VIDEO MONITOR OUT
R OUT
G OUT
B OUT
SCL
SDA
SIF OUT
SCL SDA
16
MUTE
RC
RECEIVER
A1901
KEY SW
MEMORY
IC803 SCL
SDA
IIC BUS
CONTROL
SW691
T611
CONVERTER
TRANS.
DY
15
8
5
3
2
AC PLUG
D603-D606
C607
Q613
5V
Q666
Q661
PROTECT
IC643 5V-1
IC642 9V
IC641 5V D646
D641
D647
27V
18
11
14
10
12
13
D637
27V
Q651
150V
Q642Q641
Reg.
-27V
Q643
Q686
Q682
D615
PHOTO COUPLER Q645
Q685
POWER
EW-OUT
V-OUT
H-OUT
T451
FBT
HV
200V
Q432
H-OUT
Q431
IC501
VERT. DEF.
3
6
H-BLANK
Q462
D441
Q461
L461 L462
SCREEN WIDTH CONTROL
CRT
HEATER
IF
15
1,3
2,6
20
19
K1002 AV2 SCART 2
C IN
AUDIO IN
12
4/1415 2/5/12 15
11
7
R IN
G IN
B IN
AUDIO OUT (SCART 1)
AV1
VIDEO IN
AV3 AUDIO IN
-3-
Chassis Block Diagrams

IC201 < IF/Video/Chroma/Def.> TB1262AF
-4-
IC Block Diagrams
Cync. out
H.AFC
H,V Sync.
AFC1/HAFC gain
V freq
wide
blanking
DC Resistor
BLACK DET
YS(YCbCr)
Cb2/B IN
Cbr2/R IN
Y2/CVBS2/G IN
Cb3 IN
Cb3 IN
Y3/CVBS3 IN
Cr OUT
Cb OUT
Y/MON OUT
Y/CVBS1 IN
C IN
IF DET OUT
DAC 1
DAC 3
DAC 2
Loop Filter
VIF VCO F
SIF OUT
HVcc (9V)
SIF IN
IF GND
DC NF
SIF IN
N.C.
VIF IN
VIF IN
S-Filter
APC Filter
X' tal
CW OUT
R OUT
G OUT
B OUT
VM OUT
EXT. R IN
EXT. G IN
EXT. B IN
Y sm
ABCL IN
SDA
SCL
Bed pin
45 35 50 41 40 39 37 33 28 47 46 11 25 17
42
23
20
31
27
26
32
4
74
67
78
1
69
3
71
73
70
65
68
58
61
53
52
51
55
57
56
59
54
62
43
66
36
19
44
49
48
12
13
14
18
21
22
79
80
9
7
6
34
72
75
76
77
Dig.VDD
Dig. GND
RGB Vcc (9V)
YC Vcc (5V)
V RAMP
V OUT
EHT IN
EW OUT
FBT IN
H OUT
VD
HD SCP OUT
YC GND
H DRIVE
AFC2
PalaG
Baw
IIC Bus
IF
-EW-
Coner(T/B)
Size
Trapeze
Parabola
V/EW-EW-
Size
V Centre
V Linear
V-S
SIF IN
FM Filter
IF Vcc(9V)
RF AGC
IF AGC
IF Vcc(5V)
SAW SAW
-1 st SIF-
QSS demp
AM demo
VIF/SIF
-VIF-
VCO
S-Trap
AFT (to Bus)
neg/pos
SIF
BPF
FM(AM)
RGB
-->YUV
Y1 Proc.
C-Trap
Y Delay
Chroma
PAL/
NTSC/
SECAM
YUV Switch
UV Proc.
BBTINT
Colour
Contrast
Y2 Proc.
Black stretch
DC resistor
WPL/A.C./
WPS
RGB Proc.
YUV->RGB/SW
Cut off/Drive
Y/C
YCbCr2
YCbCr3

IC Block Diagrams
-5-
IC001 < Audio AMP.> TDA7263M
1
2
3MUTE
REFERENCES
NON INVERTING INPUT (1)
INVERTING INPUT (1)
SUR/MUTING
TURN ON
AND OFF
9
5
10
8
4
6
Vcc
NON INVERTING INPUT (2)
INVERTING INPUT (2)
L
R
-
+
-
+
GND
RF I 27K
RF I 27K
SC
PROTECTION
Tj
TH
PROTECTION
OUTPUT-L
OUTPUT-R
IC501 < Vertical Output > LA7846N
THERMAL
PROTECTION PUMP UP
AMP
-
+
N.C.
Ver. Output
Output Stage Vcc
Non Inv. Input
Inverting Input
Vcc
Pump Up Output
LA7846N
13456789
10
GND
2
N.C.
N.C.

-6-
IC Block Diagrams
IC3451 < Digital TV Sound Processor of NICAM & A2 Stereo> TDA9875A
I2C-BUS
INTERFACE
ADDR1
ADDR2
P1
P2
9
20
SCL
SDA
3
13
4
5
IDENTIFICATION
CLOCK
XTALI
XTALO
SYSCLK
18
17
21
PEAK
DETECTION
SDI1
SDI2
SDO1
SDO2
SCK
WS
27
26
25
24
22
23
I
2
C-BUS
AUDIO
INTERFACE
V
DDD1
V
DDD2
VSS
D1
V
SSD2
CRESET
15
64
14
49
16
DIGITAL
SUPPLY
TEST1
TEST2 28
30 TEST
TDA9875
MOL MOR AUXOL AUXOR
61 60 58 57
SUPPLY
OPERATIONAL
AMPLIFIERS
DAC(2) DAC(2)
AUDIO PROCESSING
DAC(2)
ADC(2)
DIGITAL
SELECT
LEVEL
ADJUST LEVEL
ADJUST
DEMATRIX NICAM
DECODER
FM (AM)
DEMODULATION NICAM
DEMODULATION
INPUT SWITCH
AGC, ADC
SIF2 SIF1
10 12
SUPPLY
SOUND IF
(SIF)
VDDA1
VSSA1
Vref1
Iref
TIMING
DETECTION DAC 19
2
1
Vtune
NICAM
PCLK
SCIR1
SCIL1
SCIR2
SCIL2
EXTIR
EXTIL
MONOIN
33
34
36
37
31
32
29
SCOR1
SCOL1
SCOR2
SCOL2
LOR
LOL
47
48
51
52
63
62
ANALOG
CROSSBAR
SWITCH
CAPL2
CAPL1
CAPR1
CAPR2
42
41
45
44
PCAPR
PCAPL
VDDA2
VSSA2
VSSG
Vref2
Vref(P)
Vref(n)
54
55
38
43
35
46
39
40
SUPPLY
DAC
VDDA3
VSSA3
Vref3
VSSA4
SUPPLY DAC
REFERENCE
59
56
53
50
7
6
11
8
(first general purpose I/O pin)
(second general purpose I/O pin)
(first I2C-bus slave
address modifier)
(second I2C-bus slave
address modifier)
(I2C-bus clock)
(I2C-bus data)
(crystal oscillator input)
(crystal oscillator output)
(system clock output)
(I2S-bus data input 1)
(I2S-bus data input 2)
(I2S-bus data output 1)
(I2S-bus data output 2)
(I2S-bus clock)
(I2S-bus word select)
(digital supply voltage 1)
(digital supply voltage 2)
(supply ground 1)
(supply ground 2)
(capacitor for power-on reset)
(first test pin)
(second test pin)
(analog supply voltage 1)
(supply ground 1)
(reference voltage)
(resistor for reference
current generator)
(tuning voltage output for crystal
oscillator)
(serial NICAM data output at
728 kHz)
(NICAM clock output at 728 kHz)
(SCART 1 input right channel)
(SCART 1 input left channel)
(SCART 2 input right channel)
(SCART 2 input left channel)
(external audio input right channel)
(external audio input left channel)
(audio mono input)
(SCART 1 output right channel)
(SCART 1 output left channel)
(SCART 2 output right channel)
(SCART 2 output left channel)
(line output right channel)
(line output left channel)
(filter capacitor pin 2 )
(filter capacitor pin 1)
(filter capacitor pin 1)
(filter capacitor pin 2)
(post-filter capacitor pin right channel,
audio digital-to-analog coverter)
(post-filter capacitor pin
left channel, audio digital-
to-analog converter)
(analog supply votage 2)
(supply ground 2)
(ground guards)
(reference voltage)
(positive reference voltage)
(reference voltage ground)
(analog supply voltage)
(supply ground 3)
(reference voltage)
(supply ground 4)
(Loudspeaker (Main) output right channel)
(Loudspeaker (Main) output left channel)
(Headphone (Auxiliary) output right channel)
(Headphone (Auxiliary) output left channel)
(sound IF input 2)
(sound IF input 1)

-7-
CPU Port Functions
Pin No. Function Name Function IN/OUT
1RC IN RC signal input IN
2RESET Reset input IN
350/60 50/60Hz output (50Hz=H) OUT
4H-BLK H-Blank OUT
5V-BLK V-Blank OUT
6AV SW2 Option SW2 OUT
7AV SW1 Option SW1 OUT
8KEY IN Key switch signal input IN
9H-P Headphone mute (not used) OUT
10 RELAY To operate degauss circuit OUT
11 PROTECT Power failure detect IN
12 HP-mode Headphone mute OUT
13 BBE BBE ON/OFF OUT
14 W-P White enable OUT
15 B-OUT Blue output OUT
16 G-OUT Green output OUT
17 R-OUT Red output OUT
18 FB-OUT Fast blanking output OUT
19 SDA SDA IN/OUT
20 SCL SCL OUT
21 VDD VDD --
22 JDTO Not used --
23 N.C. Not used --
24 Vpp Not used --
25 AVDD3 Analog VDD of PLL --
26 TEST0 Test pin --
27 MCFM Test pin --
28 JTCK Test pin --
29 TXCF Analog pin for the --
Teletext slicerline PLL
30 CVBSO Not used --
31 AVDD2 Analog power supplies --
32 JTMS Not used --
33 CVBS2 Video input (H.F) IN
34 CVBS1 Video input (L.F) IN
35 AGND Analog circuit ground --
36 GND Digital circuit ground --
37 JTRSTO Test pin --
38 PXFM Analog pin for the Display --
Pixel Frequency Multiplier
39 AVDD Analog power supplies --
40 H-SYNC Horizontal Sync input IN
41 V-SYNC Vertical Sync input IN
42 ACK Answer for status OUT
43 STATUS Request for Bus open IN
44 IGNOA RGB on/off switch OUT
45 AMP-MUTE Sound mute on/off switch OUT
46 L/L’ L/L’ switch OUT
Pin No. Function Name Function IN/OUT
47 LED2 Brightness control of LED OUT
48 S-VIDEO SW S-video switch OUT
49 H-Phase H-Phase (not used) OUT
50 OSC OUT Oscillator (output) OUT
51 OSC IN Oscillator (input) IN
52 RF AGC RF Auto gain control IN
53 PITTARI PITTARI switch OUT
54 POWER TV power on/off switch OUT
55 8PIN (SC2) AV input detect IN
56 8PIN (SC1) AV input detect IN

Option Setting
-8-
After replacing the Memory IC (IC803)
The memory IC (IC803), stores the option data of TV set and service adjustments data for each circuit, therefore, when
the memory IC is replaced, it should be programmed to the following settings and “ SERVICE ADJUSTMENT” on
pages 9 to 12.
1) To enter to the Option Mode
Press and hold the F/OK button on the remote control and Programme down button (P▼)on the front panel of
the TV. The option window will appear on the screen.
PP
+
-
ON- TIMER
SORT MODE
P&P
Wel. Text
Comb Filter
WSS
- Aust
AutoVolume
3D Surround
Country
AV3
CS/A,B
ON
Tuning
ON
ON
OFF
ON
OFF
ON
BG/DK/I/LL'
ON
CS
Option Mode
2) To set the Option Mode
Select the desired option item by pressing the Programme down or up button.
To switch the option mode, use the Level up or down button.
The data which is set in the option mode is stored into the memory IC automatically.
The following table shows the available option items and default setting mode.
Option Mode Mode Description & Note
ON-TIMER ON or OFF On-timer available, default “ON”
SORT MODE Sorting or Tuning Tuning mode, default “TUNING”
P & P ON or OFF Plug & Play mode, default “ON”
WEL.TEXT ON or OFF Display message when first set up, default “ON”
Comb Filter OFF or ON For factory use, default “OFF”
WSS-Aust ON or OFF Default “ON”
Auto Volume ON or OFF Auto volume, default “OFF”
3D Surround ON or OFF Default “ON”
Country UK or IRE or B/G, D/K, I, L/L’ TV system, default “ B/G, D/K, I, L/L ”
Wide ON or OFF Wide mode, default “ON”
AV3 ON or OFF Front AV disable, default “ON”
CS/A,B CS or A/B Default “CS”
3) Exit from the Service Mode
Press the Programme information call button or turn off the TV set by using the mains switch.

Service Adjustments
-9-
After replacing the Memory IC (IC803)
The memory IC (IC803), stores the service adjustment data for each circuit, therefore, when the memory IC is
replaced, it should be programmed by using “OPTION SETTING” on previous page and the following adjustment.
Adjustable Service Adjustment
Regular
Item No. OSD Description
01 AGC AGC Adjustment
02 -- Cut-Off Drive Adjustment
03 GRY G-Drive Adjustment (White Balance)
04 GRY B-Drive Adjustment (White Balance)
05 CTR Contrast Adjustment (use factory setting) (for factory use)
06 -- Screen Adjustment mode
08 OSD OSD Positioning Adjustment
Note: Some items of the service adjustments for this chassis are controlled by the CPU (IC801), and the
adjustments are carried out by using the RC handset.
Image
Item No. OSD Description
01 P V-C P Vertical Position Adjustment
02 P H-P P Horizontal Position Adjustment
03 P V-L P Vertical Linearity Adjustment
04 P VSC P Vertical S-Correction Adjustment
05 P V-A P Vertical Size Adjustment
06 P H-S P Horizontal Size Adjustment
07 P E-P P Pin Cushion Adjustment
08 P E-T P Trapezoid Distortion Adjustment
11 P ECT P Top Corner Correction Adjustment
12 P ECB P Bottom Corner Correction Adjustment
13 P HPA P Parallelogram Distortion Adjustment
Important Notice:
Do not attempt to adjust service adjustments not listed on above otherwise it may cause loss of performance and
product safety.

Service Adjustments
-10-
1) To enter to the Service Mode
Press and hold the GREEN button on the remote control and then press the Programme down button (CH▼) on
the front panel of the TV.
Press the Programme down button to select the mode required (Regular, Image, others and TB12**).Then press
the F/OK button to select the mode.
The available adjustment items are as follows;
Image :This can be adjusted for picture image/Shapes.
Regular :This can be adjusted for the service adjustment.
Other :This is for the factory setting. DO NOT ADJUST.
TB1251 :This is for the factory setting. DO NOT ADJUST.
2) To select the mode and service item and change data value
Select the desired adjustment mode by pressing the Programme down or up button and press the F/OK button.
To select the adjustment item, use the Programme down or up button.
To change the service data, use the Level up or down button.
The data which is set in the service mode is stored into the memory IC automatically.
Regular
01 AGC 38 Image
01 P V-P 24
REGULAR mode IMAGE mode
3) Exit from the Service Mode
Press the Programme information call button or turn off the TV set by using the mains switch.
Initialisation of Memory IC (IC803)
To initialise the memory IC (IC803), press and hold the Picture mode selection (→•←)button on the remote
control, then press the Programme down button on the front panel of the TV set and then turn the Mains switch
off and on.The initialisation is now completed.
When initialised the memory IC and all of the setting data (option data and service adjustment data) stored in the IC
are reset to the default value. It is necessary to set the option settings and readjust the service adjustments listed
on page 9 and to re-tune all the channels.
Adjustment Data
Adjustment No.
and Item name
Adjustment Data
Adjustment No.
and Item name

Adjustments
-11-
IMPORTANT NOTICE
Do not attempt to adjust the following service adjustments except when adjustments are required in servicing other-
wise it may cause loss of performance and product safety.
+B VOLTAGE ADJUSTMENT
(1) Connect a DC voltmetre to TP-B and the ground.
(2) Tune the receiver to an active channel and synchronized pic-
ture. Select NATURAL picture mode by pressing the Picture
mode selection button on the remote control .
(3) Adjust voltage to 150± 0.5V DC by using VR641.
AGC ADJUSTMENT
NOTE: Do not attempt this adjustment with weak signal.
(1) Connect digital voltmetre to TP-A and GND.
(2) Tune the receiver to most clearest (or strongest) VHF station
in your area.Set the brightness and contrast controls to max-
imum. Set the colour control to minimum.
(3) Enter to the service mode and select mode “Regular”, and
select item No. 01 “Regular 01 AGC”
(4) Press the Level up (+) or Level down ( - )button to adjust
voltage to be 3.2± 0.2V DC.
FOCUS ADJUSTMENT
(1) Receive a monochrome circular pattern.
(2) Set the brightness to normal and contrast to maximum.
(3) By using FOCUS VR on the F.B.T., adjust focus control for
well defined canning lines.
SCREEN ADJUSTMENT
(1) Receive black & white pattern.
(2) Set the brightness and colour to normal, contrast to maxi-
mum.
(3) Enter to the service mode and select mode “Regular”, then
select item No. 02 “Regular 02 CUT”.The horizontal line will
appear on the screen.
(4) Using the numeric buttons shown set each colour to minimum
by decreasing to the point where any further decrease resets
the adjustment to maximum value.
BIAS ADJUSTMENT
(5) By using the buttons 1, 2, 4, 5, 7, 8 on the remote control,
adjust the line to be white.
The key allocation is as follows;
Button No. Operation
1Increase Red
2Decrease Red
4Increase Green
5Decrease Green
7Increase Blue
8Decrease Blue
GREY SCALE ADJUSTMENT
DRIVE ADJUSTMENT
(6) Select item No. 3. “Regular 03 GRY” (G-Drive) or No. 04
“Regular 04 GRY” (B-Drive) and adjust both initially to 40.
(7) Change data value of each item by using Level up (+) or
Level down (-) button to obtain the proper white balance.
PCC ADJUSTMENT
PCC ADJUSTMENT
(1) Receive cross hatch pattern and set screen mode to “FULL”.
(2) Enter to the service mode and select mode “Image”, and
select item No. 07 “Image 07 P E-P”.
(3) Press the Level up (+) or Level down ( - )button to adjust the
vertical line to be straight.
TRAPEZOID ADJUSTMENT
(1)Receive cross hatch pattern and set screen mode to
“FULL”.
(2)Enter to the service mode and select mode “Image”, and
select item No. 08 “Image 08 P E-T”.
(3)Press the Level up (+) or Level down ( - )button to correct
the trapezium distortion of the vertical line.
CORNER ADJUSTMENT
(1)Receive cross hatch pattern and set screen mode to
“FULL”.
(2)Enter to the service mode and select mode “Image”, and
select item No.11 “Image 11 P ECT”for top corner adjustment
or item No. 12 . “Image 12 P ECB” for bottom corner adjust-
ment.
(3)Press the Level up (+) or Level down ( - )button to correct
the distortion of the vertical line around the corners..

Adjustments
-12-
HORIZONTAL ADJUSTMENT
HIGH-VOLTAGE CONFIRMATION
VERTICAL ADJUSTMENT
HORIZONTAL CENTRING ADJUSTMENT
(1) Receive circular pattern and set screen mode to “FULL”.
(2) Enter to the service mode and select mode “Image”, and
select item No. 02 “Image 02 P H-P”.
(3) Press the Level up (+) or Level down ( - )button to adjust the
horizontal centre.
VERTICAL CENTRING ADJUSTMENT
(1) Receive circular pattern and set screen mode to “FULL”.
(2) Enter to the service mode and select mode “Image”, and
select item No. 01 “Image 01 P V-C”.
(3) Press the Level up (+) or Level down ( - )button to adjust the
vertical centre.
Horizontal centre
HORIZONTAL WIDTH ADJUSTMENT
(1) Receive circular pattern and set screen mode to “FULL”.
(2) Enter to the service mode and select mode “Image”, and
select item No. 06 “Image 06 P H-S”.
(3) Press the Level up (+) or Level down ( - )button to adjust the
horizontal width. Note: +B (+150V) Voltage Check and Grayscale Adjustment must
be completed before attempting High Voltage Check.
(1) Connect high-voltage meter to the anode of CRT and the
ground.
(2) Receive circular pattern and set screen mode to “FULL”.
(3) Set controls for brightness and contrast to maximum.
(4) Confirm high voltage is within 29.5 KV and 31.5 KV at maxi
mum beam current.
VERTICAL HEIGHT ADJUSTMENT
(1)Receive circular pattern and set screen mode to “FULL”.
(2)Enter to the service mode and select mode “Image”, and
select item No. 05 “Image 05 P V-A”.
(3)Press the Level up (+) or Level down ( - )button to adjust the
vertical height.
OSD POSITIONING ADJUSTMENT
(1) Receive circular pattern and set screen mode to “FULL”.
(2) Enter to the service mode and select mode “Regular”, and
select item No. 08 “Regular 08 OSD”. The OSD test bar will
appear on the top of screen.
(3) Press the Level up (+) or Level down ( - )button to adjust
proper OSD positioning.

-13-
Signals: Use a pattern generator which can output red,
green, blue and white raster and crosshatch
pattern signals.
Procedure: Carry out purity adjustment first, and then carry
out convergence adjustment.
Preparation: The deflection yoke may have several
correction magnets attached to its outer
edge. If replacing the picture tube, the
positions of the magnets can be changed and
they can be re-used, so remove these
magnets and keep them safely so that they
do not get lost.
PURITY ADJUSTMENTS
1. Place the picture so that its front faces west.
2. Insert the power plug into a wall outlet, and then turn on
the power for the TV and de-magnetize the TV using its
own degaussing circuit.
3. Loosen the screw which is holding the deflection yoke
(with integrated purity magnets), and them move the
deflection yoke forward as far as it will go. Remove the
rubber wedge at this time.
4. Turn off the red and blue raster so that only the green
raster is on.
5. Adjust the angle between the tabs (wings) on purity
magnets to centre the vertical green belt in the picture
tube screen. (See Figures 2 and 3.)
NOTE:This adjustment can only be carried out by
changing the angle, not by rotating the tabs up and
down.
6. Gently move the deflection yoke back to the position
where the green band fills the whole of the picture tube
screen, and then tighten the screw to secure the
deflection yoke in place.
7.If there is any colour distortion around the edges, correct
it by attaching magnets to the outer edge of the
deflection yoke. The magnets should be attached so
that the line running from the position of the distortion to
the centre of the picture tube intersects the deflection
yoke.The colours on the magnets indicate the north and
south poles of the magnets. Attach the magnets in
whichever direction causes the distortion to
disappear.(See Figures 1 and 4. The south and north
pole positions are shown as a guide.)
8. Switch the screen to red and blue raster and check that
there is no colour distortion. If there is any distortion,
adjust the angles of purity magnets tabs or the forward-
back position of the deflection yoke, or change the
attachment positions of the
correction magnets.
Purity and Convergence Adjustment
CAUTION:The Convergence and Purity adjustments have been made at the factory. Readjustment
should be made only after picture tube or deflection yoke replacement, following the steps below:
Deflection yoke
mounting scrrew
Rubber wedge
Correction
magnet
Move the deflection
yoke back and forth to
adjust the purity
GREEN band
Magnet attachment position
Deflection
Yoke outer edge
Color distortion
Figure 1
Figure 2
Figure 3
Figure 4
N
S
1
2
3
4
SIX-POLE
MAGNET TABS
FOUR-POLE
MAGNET TABS
ANGLE
OF TABS
PURITY
MAGNET
TABS
Change the angle to adjust the green band so that it is
centred in the screen.

-14-
Purity and Convergence Adjustment
CONVERGENCE ADJUSTMENT
Preparation: After carrying out purity adjustment and
before proceeding to convergence
adjustment, provisionally insert the rubber
wedge so that there is no vertical or
sideways play in the deflection yoke.
Signals: Display a crosshatch pattern.
1. Red/blue centre adjustment
Adjust the angle between the tabs (1) and (2) in Figure
5 and rotate them together until the lines of the red and
blue crosshatch patterns (vertical and horizontal lines)
are superimposed in the centre of the screen.
2. Green and red/blue centre adjustment
Adjust the angle between the tabs (3) and (4) in Figure
5 and rotate them together until the lines of the green
crosshatch pattern are superimposed with the red/blue
crosshatch pattern (vertical and horizontal lines) which
were superimposed in step 1).
3.Vertical lines at screen centre (Red and Blue)
Use the VR2 control (see Figure 8) at the top of the
deflection yoke to correct the vertical line convergence
at the centre of the screen.(See Figure 9.)
4.Vertical lines at screen top and bottom
Use the VR1 control (see Figure 8) at the top of the
deflection yoke to correct the vertical line convergence
at the top and bottom of the screen. (See Figure 10.)
5. Horizontal lines at screen top and bottom
Rotate the Deflection yoke to the left or right to correct
the horizontal line convergence at the top and bottom of
the screen. (See Figure 11.)
If vertical lines are intersecting at the top and bottom,
use a screwdriver to adjust the Balance coil at the top of
the deflection yoke. (See Figure 12.)
Red
Blue
Figure 6
Red/Blue
Green
Figure 7
Red Blue
Figure 9
Figure 5
Adjust the angle rotation of tabs
(1) and (2) to align the vertical
and horizontal lines.
Adjust the angle and rotation of
tabs (3) and (4) to align the vertical
and horizontal lines.
Use the VR2 control to correct.
Red
Blue
Figure 10
Use the VR1 control to correct.
Blue
Red
Figure 11
Rotate the DY to correct.
Blue
Red
Figure 12
Use the Balance coil to correct
1
2
3
4
SIX-POLE
MAGNET TABS
FOUR-POLE
MAGNET TABS
ANGLE
OF TABS
PURITY
MAGNET
TABS
Balance
coil
VR1
VR2
Figure 8

-15-
Mechanical Disassembly
CABINET BACK REMOVAL
1. Refer to Figure 1, remove 11 screws.
2. Pull off cabinet back and remove.
Figure 1. Cabinet Back Removal
When an abnormality occurs during TV reception, it causes pin 11 of the CPU to go continually Low for about 2
second.The CPU detects that this has occurred and outputs the signal from pin 54 to switch off the power supply
lines.
■Releasing the protective circuit and restoring power supply
To release the protective circuit and restore power supply, turn the power to the TV set OFF and then ON again via
either the main power switch or the ON-OFF button on the remote control. This will work only if the power supply
trouble was temporary. If there is permanent trouble such as a damaged circuit, power cannot be restored and the
circuit will have to be repaired.
This TV set has a built-in power supply protection circuit.
It is provided to protect the TV set in case of a power supply circuit malfunctions. When something abnormality occurs
during TV reception, the TV set goes to the stand-by mode.
Protection Circuit
ANT. 75Ω
AV2 AV2

ANT. 75Ω
AV2 AV2
PP
+
-
-16-
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
1 610 315 7696 BUTTON POWER-F8WZ
610 229 8406 SPRING-E3HA
(for POWER BUTTON)
2 610 298 4620 DEC IND-C3HB
3 610 315 7702 BUTTON UNITED-F8WZ
4 610 315 7634 ASSY,CABINET FR-F8WZ
4-a 610 315 7719 CABINET FRONT-F8WZ
4-b 610 315 7733 DOOR-F8WZ
5 645 040 4672 BADGE,SANYO
or 645 041 7269 BADGE,SANYO
6 610 303 7745 CABINET BACK-C6BA
7 610 256 7670 HOLDER AC CORD-SGP-D4VA
8 645 052 2697 ASSY,REMOCON JXMTA
9 610 297 9879 RC-BATTERY LID-JXMTA
610 315 2370 INSTRUCTION MANUAL-F8WZ
Key No. Part No. Description Key No. Part No. Description
1
2
3
4-b
5
7
6
9
Cabinet Parts List Service Ref. No. CP32WF2-00 & CP32WF2-50
4-a 8

-17-
F8WY
OUT OF CIRCUIT BOARD
PICTURE TUBE
Q901 414 013 0900 CRT W76QEN693X001(S)
COIL
L901 645 055 6593 COIL,DEGAUSSING
MISCELLANEOUS
SP901 645 054 3050 SPEAKER,8
645 002 4313 SPEAKER,8
645 047 2046 SPEAKER,8
645 032 5687 SPEAKER,8
SP902 645 054 3050 SPEAKER,8
645 002 4313 SPEAKER,8
645 047 2046 SPEAKER,8
645 032 5687 SPEAKER,8
W901 645 068 9758 CORD,POWER-2.4MK-A5002
W902 610 316 4878 ASSY,WIRE GND CONNECTOR F
W902A 610 206 0300 GROUNDING SPRING-S4LA
W902B 610 206 0300 GROUNDING SPRING-S4LA
Service Ref. No. CP32WF2-00
610 317 3597 ASSY,PWB,MAIN F8WZ
1AA0B10S14500
Service Ref. No. CP32WF2-50
610 317 3634 ASSY,PWB,MAIN F8WY
1AA0B10S14900
Note:The composition parts of ASSY, PWB, MAIN F8WZ and
ASSY, PWB, MAIN F8WY are completely the same.
TRANSISTOR
Q001 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q043 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q044 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
!
!
!
Chassis Electrical Parts List Service Ref. No. CP32WF2-00 & CP32WF2-50
Ref. No. Part No. Description Ref. No. Part No. Description
Product safety should be considered when a component replacement is made in any area of a receiver.
Components indicated by a mark in this parts list and the circuit diagram show components whose value have
special significance to product safety. It is particularly recommended that only parts specified on the following parts
list be used for components replacement pointed out by the mark.
!
Note: Parts order must contain Service Ref. No., Part No., and descriptions. The main PCB unit will be supplied without tuner and
flyback transformer. They should be ordered separately.
Read description in the Capacitor and Resistor as follows:
CAPACITOR
CERAMIC 100P K 50V
Rated Voltage
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF C : ±0.25pF
D : ±0.5pF F : ±1PF G : ±2pF
R : ±0.25-0pF S : ±0-0.25pF E : +0-1pF
More than 10pF
A : Not specified B : ±0.1% C : ±0.25%
D : ±0.5% F : ±1% G : ±2%
H : ±3% J : ±5% K : ±10%
L : ±15% M : ±20% N : ±30%
P : +100-0% Q : +30-10% T : +50-10%
U : +75-10% V : +20-10% W : +100-10%
X : +40-20% Y : +150-10% Z : +80-20%
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC...........Ceramic
MT-PAPER.........Metallized Paper
POLYESTER......Polyester
MT-POLYEST.....Metallized Polyester
POLYPRO..........Polypropylene
MT-POLYPRO....Metallized Polypropylene
COMPO FILM.....Composite film
MT-COMPO........Metallized Composite
STYRENE...........Styrene
TA-SOLID...........Tantalum Solid
AL-SOLID...........Aluminium Solid
ELECT................Electrolytic
NP-ELECT..........Non-polarised Electrolytic
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
DL-ELECT..........Double Layered Electrolytic
RESISTOR
CARBON 4.7K J A 1/4W Rated Wattage
Performance Symbols:
A: General B: Non flammable Z: Low noise
Other: Temperature coefficient
Tolerance Symbols:
A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%
F: ±1% G: ±2% J: ±5% K: ±10%
M: ±20% P: +5-15%
Rated value, ohms:
K: 1,000, M: 1,000,000
Material:
CARBON........... Carbon
MT-FILM............ Metal Film
OXIDE-MT......... Oxide Metal Film
SOLID................ Composition
MT-GLAZE.........Metal Glaze
WIRE WOUND...Wire Wound
CERAMIC RES.. Ceramic
FUSIBLE RES....Fusible
NOTES:

-18-
F8WY
405 173 9902 TR 2SC3928A1S
Q1041 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q1042 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q1043 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q1044 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q1202 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q1206 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q121 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q133 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q141 405 015 9701 TR 2SC2814-F4-TB
405 015 9909 TR 2SC2814-F5-TB
Q151 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q152 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q153 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q161 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q162 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q211 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q242 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q243 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q244 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
Ref. No. Part No. Description Ref. No. Part No. Description

405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q3452 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q3453 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q3454 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q3455 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q431 405 018 0507 TR 2SC3332-R
405 018 0606 TR 2SC3332-S
Q432 405 171 4404 TR S2055N—3E
Q451 406 012 1408 TR 2SK2010-CTV-YA14
Q461 405 052 7906 TR 2SB1274-Q
405 052 8002 TR 2SB1274-R
405 052 8101 TR 2SB1274-S
405 138 1309 TR 2SB1565-E
405 138 1408 TR 2SB1565-F
Q462 405 039 3303 TR 2SC3114-R
405 039 3402 TR 2SC3114-S
405 017 1901 TR 2SC3114-T
Q491 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q611 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q612 405 058 0208 TR 2SC3807-R-CTV-YA
Q613 405 095 0407 TR 2SC4429-L-YB
405 095 0308 TR 2SC4429-M-YB
Q641 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q642 405 089 3001 TR 2SC4487-S
405 089 3100 TR 2SC4487-T
405 022 2504 TR 2SD1347-S
405 022 2603 TR 2SD1347-T
Q643 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q645 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q651 405 089 0000 TR 2SA1707-S
405 089 0109 TR 2SA1707-T
405 009 6907 TR 2SB985-S
405 009 7003 TR 2SB985-T
Q661 405 001 9302 TR 2SA1020-Y
405 008 4805 TR 2SB764-E
Q666 405 058 0208 TR 2SC3807-R-CTV-YA
Q682 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q685 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q686 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q802 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
-19-
F8WY
Ref. No. Part No. Description Ref. No. Part No. Description

-20-
F8WY
405 173 9902 TR 2SC3928A1S
Q804 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q805 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
Q807 405 134 5905 TR 2SA1037AK-T146-R
405 147 2205 TR 2SA1037AK-S-T146
405 002 0308 TR 2SA1037K T146 R
405 002 0407 TR 2SA1037K T146 S
405 002 6706 TR 2SA1179-M6-TB
405 002 6904 TR 2SA1179-M7-TB
405 163 1503 TR 2SA1179N-M6-TB
405 163 2708 TR 2SA1179N-M7-TB
Q808 405 014 4509 TR 2SC2412K T146 R
405 014 4608 TR 2SC2412K T146 S
405 015 8704 TR 2SC2812-L6-TB
405 015 8902 TR 2SC2812-L7-TB
405 163 1602 TR 2SC2812N-L6-TB0
405 163 1701 TR 2SC2812N-L7-TB0
405 173 9803 TR 2SC3928A1R
405 173 9902 TR 2SC3928A1S
INTEGRATED CIRCUIT
IC001 409 301 4906 IC TDA7263M
IC1201 409 161 3408 IC LA7954
IC1401 409 211 7301 IC MC14053BFL
409 051 2900 IC TC4053BF-TP1
IC201 409 559 3201 IC TB1262AF
IC3451 409 445 1403 IC TDA9875A/V2
IC501 409 374 0607 IC LA7846N
IC641 409 241 5407 IC BA178M05T
409 265 4806 IC L78M05CV
409 172 1509 IC MC78M05CT
409 320 5700 IC UPC78M05AHF
IC642 409 367 2809 IC BA178M09T
409 370 0007 IC MC78M09CT
409 366 7904 IC UPC78M09AHF
IC643 409 241 5407 IC BA178M05T
409 265 4806 IC L78M05CV
409 172 1509 IC MC78M05CT
409 320 5700 IC UPC78M05AHF
IC801 410 508 8208 IC ST92195C8B1/MCY
IC803 409 495 7103 IC CAT24WC08P
410 495 7901 IC AT24C08A-10PI-2.7
409 383 6805 IC 24LC08B/P
CAPACITOR
CR645TM 404 084 8806 ELECT 1U M 50V
403 049 0008 ELECT 1U M 50V
C001 403 314 5905 CERAMIC 0.47U K 16V
403 307 8807 CERAMIC 0.47U K 16V
C002 403 215 2300 CERAMIC 0.012U K 50V
C003 403 314 5905 CERAMIC 0.47U K 16V
403 307 8807 CERAMIC 0.47U K 16V
C004 403 215 2300 CERAMIC 0.012U K 50V
C005 403 046 3507 ELECT 33U M 25V
C006 403 046 3507 ELECT 33U M 25V
C007 403 164 0204 CERAMIC 0.1U Z 25V
C008 403 164 0204 CERAMIC 0.1U Z 25V
C009 403 164 0204 CERAMIC 0.1U Z 25V
C010 404 089 7200 ELECT 100U M 25V
403 042 2405 ELECT 100U M 16V
C011 403 209 7205 ELECT 2200U M 25V
C012 403 209 7205 ELECT 2200U M 25V
C013 403 164 0204 CERAMIC 0.1U Z 25V
C015 404 087 4904 ELECT 47U M 25V
403 054 0703 ELECT 47U M 35V
C021A 403 052 8503 ELECT 1000U M 35V
C053 403 169 2807 CERAMIC 330P J 50V
C056 403 157 6800 CERAMIC 680P K 50V
C101 404 087 4904 ELECT 47U M 25V
403 047 3100 ELECT 47U M 25V
C1010 403 157 3601 CERAMIC 100P J 50V
C1012 403 157 3601 CERAMIC 100P J 50V
C1014 403 113 3805 CERAMIC 1000P K 50V
C1015 403 248 1905 ELECT 10U M 16V
C1016 403 113 3805 CERAMIC 1000P K 50V
C1017 403 049 4204 ELECT 10U M 50V
C102 403 039 3507 ELECT 470U M 6.3V
C1020 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
C1021 403 157 3601 CERAMIC 100P J 50V
C1024 403 157 3601 CERAMIC 100P J 50V
C1026 403 113 3805 CERAMIC 1000P K 50V
C1027 403 049 4204 ELECT 10U M 50V
C1028 403 113 3805 CERAMIC 1000P K 50V
C1029 403 049 4204 ELECT 10U M 50V
C103 403 039 3507 ELECT 470U M 6.3V
C1034 403 157 3601 CERAMIC 100P J 50V
C104 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C1042 403 049 4204 ELECT 10U M 50V
C1043 403 049 4204 ELECT 10U M 50V
C1044 403 113 3805 CERAMIC 1000P K 50V
C1045 403 113 3805 CERAMIC 1000P K 50V
C106 403 215 2201 CERAMIC 0.01U K 50V
C109 403 215 2201 CERAMIC 0.01U K 50V
C110 403 215 2201 CERAMIC 0.01U K 50V
C113 403 069 8305 CERAMIC 0.01U Z 50V
C120 404 087 4904 ELECT 47U M 25V
403 047 3100 ELECT 47U M 25V
C1200 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C1202 404 087 4904 ELECT 47U M 25V
403 047 3100 ELECT 47U M 25V
C1203 403 215 2201 CERAMIC 0.01U K 50V
C1204 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C1205 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C1206 403 145 9905 CERAMIC 22P J 50V
C121 403 215 2201 CERAMIC 0.01U K 50V
C1211 403 153 9300 CERAMIC 82P J 50V
C1212 403 153 9300 CERAMIC 82P J 50V
C1213 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C1214 403 153 9300 CERAMIC 82P J 50V
C1215 403 153 9300 CERAMIC 82P J 50V
C1218 403 153 9300 CERAMIC 82P J 50V
C123 403 215 2201 CERAMIC 0.01U K 50V
C124 404 084 8905 ELECT 10U M 50V
403 049 4204 ELECT 10U M 50V
C125 404 084 9001 ELECT 2.2U M 50V
Ref. No. Part No. Description Ref. No. Part No. Description