Saracen D02614 User manual

1
Shower Curtain Rod
Fittings instruction for the following product:
D02614 - 1200mm x 1200mm Stainless Steel Shower Curtain Rod
Fixing Pack Contents
(A) Fixing screws x 6
(B) Wall plugs x 6
(C) Hex head key x 1
(D) Spare grub screw x 3
Tools Required (not supplied)
Pencil; Tape measure; Cross-head screwdriver; Spirit level; Drill; 6mm masonry drill bit
(6mm ceramic drill bit optional); Fine toothed hacksaw.
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Note: The wall plugs supplied are for use on solid walls only. For cavity walls or
plasterboard use specialist xings that are available from all good DIY stores.
Home Safety Advice
• Itisrecommendedthattwopeopletthisproducttoensurethatitisttedsafely.
• Always take care when using power tools, particularly in the bathroom.
• Always check for hidden cables and pipework before drilling and take extreme care if there is
any water in the working area.
• It is advisable to use a residual current circuit breaker (RCCB).
• Always wear suitable eye protection when drilling.
• Iftheproductistobettedonaceramictiledwall,aceramicdrillbitshouldbeused.
• Always ensure that the drill hole passes through the central tiled area rather than through the
grouted area. To prevent damage to the tile, mask the area around the hole with tape before
drilling.
• Do not strike the product with hard or sharp objects.
• Do not use product as a grab rail.
Product Care
Toretainthebestqualitynish,cleanproductregularlywithasoftdampcloth.
Do not use abrasive or chemical cleaners as these will damage the product.
Fitting Instruction
1. Lay out the components. Measure around the bath or shower tray to determine exact
dimensions and shape. Join the rod sections together using the corner joint, tapping gently
into place if required.
Note: The rod can be cut to length if required using a ne toothed hacksaw, but always cut
the end of the rod which ts and is concealed within the wall bracket. Ensure the end of the
rod is cut square and is deburred.
R&R 048 R01

2R&R 048 R01
2. Measure the drop of the shower curtain to determine the position of the wall brackets,
allowingforthecurtainhooksandsucientoverlapinthebathortray.Placetherstwall
bracket in the desired location and mark through the screw holes with a pencil. (See Fig.1)
3. Using a 6mm masonry drill, drill the hole in the marked position to a depth of 30mm. If drilling
through tiles, please pre-drill using a ceramic drill bit.
4. Insertthewallplugstothesurfaceofthewall.Ifttingtoatiledsurface,thewallplugshould
be inserted below the surface of the tile to avoid cracking. Fix the wall bracket to the wall
using the screws provided. (See Fig.2)
5. Inserttherodassemblyintothexedwallbracketanduseitasaguidetopositionthesecond
wall bracket. Check the assembly is horizontal (See Fig.3)
6. Secure the second wall bracket into position by repeating steps 2-4.
7. Slide the wall bracket covers and the ‘C’ hooks onto the rod prior to inserting the rod
assemblyintothewallbrackets.Slidethecoversoverthewallbracketstoconsealallxings.
Secure each cover by tightening the grub screws, one through the clearance hole of the wall
bracket onto the surface of the rod, and the other onto the wall bracket. (See Fig.4)
8. Determine a suitable location for the ceiling support rod. Attach the ceiling support bracket
‘A’ onto the rod by clipping it in place. Measure the distance between the ceiling and the top
of the ceiling support bracket ‘A’ and add 28mm (which is the depth of tube into the ceiling
support bracket) to this dimensions (See Fig.5). Cut the ceiling support tube to the required
lengthusinganetoothedhacksaw.Ensuretheendofthetubeiscutsquareandisdeburred.
9. Assemble the ceiling bracket and bracket cover onto the ceiling support rod, check it is
vertical and using a pencil to mark its screw hole positions (See Fig.6). Drill and screw the
bracket to ceiling using the screw provided, either into a ceiling joist or use a cavity wall plug.
Slide the cover over the bracket and secure by tigthening the grub screws, one through the
clearance hole on the ceiling bracket onto the surface of the rod, and the other onto the
ceiling bracket (See Fig.4).
10. Secure the ceiling rod into the ceiling support bracket using a screw provided (See Fig.5).
DONOTOVERTIGHTEN.Checkthecurtainrodishorizontalandadjustifrequired.
Wolseley UK Ltd
Warwickshire
CV31 3HH
www.wolseley.co.uk
(A)
Fig.1 Fig.2 Fig.3
Fig.6Fig.5Fig.4