Saswell SAS2010DE User manual

1
Brezžični sprejemnik | Wireless receiver
SASWELL SAS2010DE
Uporabniški priročnik
User manual

2
Primeri el. vezave / electrical wiring examples
1. El. Ventil / El. valve 2. Peč / Boiler

3
3. Električno talno ogrevanje / Electrical floor heating
4. Shema / Scheme

4
SI | Uporabniški priročnik
Brezžični sprejemnik SAS2010DE je glavna digitalna stikalna enota, ki brezžično komunicira s Saswell termostati in
upravlja ogrevalne enote, kot so peči, bojlerji, obtočne črpalke, ipd.
Navodila za uporabo in vzdrževanje so del splošnih prodajnih pogojev. Pridržujemo si pravico do sprememb detajlov,
tehnologije in izvedbe. Garancija velja le skupaj z računom in podrobno obrazložitvijo napake. Dopuščamo možnost
napak v besedilu.
Varovanje narave
Elektronske naprave in baterij po koncu življenjske dobe ne odlagajte med mešane komunalne odpadke
temveč uporabite zbirna mesta ločenih odpadkov. S pravilno odstranitvijo izdelka boste preprečili
negativne vplive na človeško zdravje in okolje. Reciklaža materialov prispeva varstvu naravnih virov.
Več informacij o reciklaži tega izdelka Vam ponudijo upravne enote, organizacije za obdelavo
gospodinjskih odpadkov ali prodajno mesto, kjer ste izdelek kupili.
v1

5
Pomembna opozorila pred prvo uporabo, namestitvijo in vzdrževanje naprave:
Pred prvo uporabo pozorno preberite navodila za uporabo ne samo termostata, ampak tudi peči ali klimatske naprave.
• Pred inštalacijo termostata izklopite dovod električnega toka! • Priporočamo, da inštalacijo opravi kvalificiran delavec!
• Električni krog mora biti zavarovan z varovalko, ki ne presega tokovne obremenitve ožičenja • Pri montaži upoštevajte
vse varnostne predpise • Izdelka ne izpostavljajte neposredni sončni svetlobi, ekstremnemu mrazu, vlagi in naglim
spremembam temperature. To bi znižalo natančnost merjenja temperature • Izdelka ne nameščajte na mesta, ki so
nagnjena k vibracijam in pretresom – to lahko povzroči poškodbe • Izdelka ne izpostavljajte prekomernemu tlaku,
sunkom, prahu, visokim temperaturam ali vlagi saj le te lahko povzročijo poškodbe na kateri izmed funkcij izdelka,
krajšo energetsko vzdržljivost, poškodbo baterij in deformacije plastičnih delov • Izdelka ne izpostavljajte dežju ali vlagi,
kapljajoči in brizgajoči vodi • Na izdelek ne postavljajte virov ognja, npr. prižgane svečke ipd. • Izdelka ne postavljajte
na mesta, kjer ni zadostnega kroženja zraka • V prezračevalne odprtine ne vtikajte nobenih predmetov • Ne posegajte
v notranjo električno napeljavo izdelka – lahko ga poškodujete in s tem prekinite veljavnost garancije. Izdelek sme
popravljati le usposobljen strokovnjak • Za čiščenje uporabljajte zmerno navlaženo blago krpo. Ne uporabljajte raztopin
ali čistilnih izdelkov – lahko poškodujejo plastične dele in električno napeljavo • Izdelka ne potapljajte v vodo ali v druge
tekočine • Pri poškodbah ali napaki izdelka ne popravljajte sami. Predajte ga v popravilo prodajalni, kjer ste ga kupili •
Izdelka ne smejo uporabljati osebe (vključno otrok), ki jih fizična, čutna ali mentalna nesposobnost ali pomanjkanje
izkušenj, in znanj ovirajo pri varni uporabi naprave, če pri tem ne bodo nadzorovane, ali če jih o uporabi naprave ni
poučila oseba, ki je odgovorna za njihovo varnost • Nujen je nadzor nad otroki, da bo zagotovljeno, da se ne bodo z
napravo igrali.
Za izdelek je bila izdana izjava o skladnosti. Ta in ostala dokumentacija je dostopna na spletni strani www.sen-
controls.eu. Proizvajalec izdelka je SASWELL CONTROLS (HONGKONG) LTD.
Uvoznik in distributer za Saswell je Sen Controls d.o.o., Belokranjska cesta 29, 8340 Črnomelj, Slovenija

6
Lastnosti
•LED prikaz delovanja
•Zaščita IP21
Specifikacije enote
•Napajanje 100-240V izmenične napetosti, 50/60Hz
•Komunikacija: Brezžična, RF, frekvence 868MHz (FSK), domet do 100m
•Natančnost ± 1°C
•Temperatura okolice delovanja 0°C ~50°C
•Skladiščna temperatura -10°C ~ +60°C
•Dimenzije 113 x 83 x 30mm

7
3
4
5
Opis sprejemnika in funkcij
Opis sprejemnika
1. Vijak za odpiranje ohišja sprejemnika
2. Glavna in edina tipka za upravljanje s sprejemnikom
3. LED indikator A (zelen / rdeč LED)
4. LED indikator B (zelen LED)
5. LED indikator C (rumen LED)
Tipka, vklop in izklop
Naprava ima zgolj eno tipko in s to upravljate vse funkcije naprave.
Primarna funkcija tipke je seveda vklop oz. izklop sprejemnika. Napravo
vklopite ali izklopite s kratkim pritiskom na tipko. Če je naprava priključena
na napajanje in sprejemnik izklopljen, ne sveti nobeden izmed LED
indikatorjev. Ko je sprejemnik vklopljen na njemu vedno sveti indikator A.
Potreba po ogrevanju
Ko termostat izda ukaz, da je potreba po ogrevanju, na termostatu zasveti
LED indikator B. Ko potrebe po ogrevanju več ni, le ta ugasne.
Komunikacija med napravami, TEST povezave
Ko termostat komunicira s sprejemnikom ali obratno, na kratko in hitro dvakrat
zasveti LED indikator C. Na takšen način lahko tudi spremljate ali je povezava med napravami uspešna in pošiljate
ukaze iz termostata (spreminjate temperaturo) v sprejemnik. Prikaz za komunikacijo bi moral zasvetiti, kot opisano.
1
2

8
Prisilno delovanje izhoda
Sprejemnik ima možnost vklopa prisilnega delovanja izhoda, kar pomeni da sprejemnik ignorira komunikacijo s
termostatom in vključi izhod oz. pošlje signal na ogrevalno enoto za ogrevanje. To je uporabno v primeru, da pride do
okvare termostata ali kakšni drugi situaciji.
Funkcijo vklopite na sledeči način:
Termostat izklopite s kratkim pritiskom na tipko. Vsi LED indikatorji bi morali ugasniti. Sedaj držite tipko 8 sekund.
Vmes se osvetli LED indikator C, vendar še vedno držite tipko! Po osmih sekundah se osvetlita LED indikatorja A in B,
oba zeleno. S tem je funkcija prisilnega delovanja izhoda vklopljena. Funkcijo izklopite s kratkim pritiskom na tipko.
Omejitev najvišje temperature delovanja
Sprejemnik ima možnost omejitve najvišje temperature delovanja pri uporabi električnega talnega ogrevanja. Le ta
deluje zgolj ob uporabi senzorja za talno gretje, ki se ga priključi v sprejemnik.
Senzor mora biti specifikacije NTC 100K.
Funkcijo vklopite na sledeči način: V sprejemnik ste priključili senzor in vklopili napravo, da sveti vsaj LED indikator A
(rdeče). Sedaj držite tipko 3 sekunde in LED indikator A (rdeče) se bo ugasnil in začel utripati zeleno. Sedaj s
pritiskanjem na tipko spreminjate kombinacijo osvetljenih LED indikatorjev in s tem tudi nastavitev temperature. Če
sveti:
- LED A in LED B (oba zeleno) : 30°C
- LED A (zeleno) in LED C (rumeno): 40°C
- LED A (zeleno), LED B (zeleno) in LED C (zeleno): 55°C
- utripajoči LED A (zeleno) : omejitev temperature ni vklopljena
Za izhod iz urejanja držite tipko 3 sekunde. Tako se tudi shrani želena funkcija.

9
Povezovanje termostata s sprejemnikom
Če ste dobili sprejemnik zraven termostata, sta le ta že privzeto sparjena. V primeru da nista oz. da želite ponoviti
parjenje naprav, sledite naslednjim navodilom
Sprejemnik izklopite, da ne sveti nobeden izmed LED indikatorjev. Sedaj držite tipko za 3 sekunde, da se osvetli LED
indikator C (rumena). Sprejemnik je tako pripravljen na parjenje.
Sedaj samo še sledite navodilom Vašega termostata za parjenje. Ko je parjenje izvedeno, na sprejemniku LED
indikator C osvetli 5 krat rumeno in nato izklopi. Na termostatu se po navadi, v primeru uspešnega parjenja izpiše
številka 1.

10
Namestitev sprejemnika in električna vezava
Montaža sprejemnika
Odprite ohišje sprejemnika in sicer tako, da od vijačite vijak (1) na vrhu ohišja in previdno odprete iz sprednje strani (2).
Sedaj pri vijačite zadnji del ohišja na steno (3). Ko ste opravili tudi električno vezavo, previdno zaprite ohišje in pri
vijačite vijak nazaj na svoje mesto (4).
Nasvet: Sprejemnik ne montirajte na kovinsko podlago oz. zelo blizu kovine ter ostalih električnih naprav, saj lahko
pride do motenj pri brezžični komunikaciji med sprejemnikom in termostatom. Prav tako je definiran domet RF 100m
teoretične narave in v praksi na to specifikacijo vpliva ogromno dejavnikov (od tipa hiše, električnih naprav, …), zato
bodite pozorni da montirate sprejemnik na dobro pozicijo in da bo komunikacija s termostatom možna.

11
Električna vezava sprejemnika
Zopet, pred samo električno vezavo sprejemnika, preberite vsa varnostna opozorila, navodila za uporabo vseh
priključenih naprav in izključite glavno varovalko v vašem objektu. Montažo naj izvede kvalificirana in usposobljena
oseba!
Shema:
L – Faza
L1 – Napajanje porabnika
N – Nula
N1 – Napajanje porabnika
NC – Mirovni oz. zaprti kontakt (Normaly Closed)
NO – Delovni oz. odprti kontakt (Normaly Open)
COM – Skupni kontakt
S1, S2 – Kontakt za priklop senzorja za talno gretje (NTC 100K)*
* Kontakti niso vključeni

12
EN | User manual
Wireless receiver SAS2010DE is the main digital switching unit, which communicates with Saswell thermostats via
wireless radio frequency and manages heating units (boilers, pumps, ...) and other devices.
The user manual is a part of the general terms and conditions of sale. We reserve the right to change the details,
technology and performance. The guarantee is valid only with the account. We allow the possibility of errors in the text.
Enviriomental protection
Do not place electronic devices and batteries after the end of their life in mixed municipal waste - use
collection points of separate waste. By properly removing the product, you will prevent negative effects
on human health and the environment. Recycling of materials contributes to the protection of natural
resources. More information on the recycling of this product is offered to you by administrative units,
household waste treatment organizations or the point of sale where you purchased the product.

13
Important notes before first use, installation and maintenance
Before use, carefully read the manual not only for the thermostat, but also for the Heating device (heat pump, pumps,
boilers, etc.) • Turn off the power supply before installing the thermostat! • We recommend that the installation is done
by a qualified electrician • the electrical circuit must be secured with a fuse that does not exceed the current load of
wiring • Please note all safety instructions before installing • Do not expose the product to direct sunlight, extreme cold,
humidity and sudden temperature changes. This would reduce the accuracy of the temperature measurement • Do not
place the product in places that are prone to vibrations and shocks - this can cause damage • Do not expose the
product to excessive pressure, shock, dust, high temperatures or moisture, as these can cause damage to one of the
functions product, shorter energy endurance, damage to batteries, and deformation of plastic parts. • Do not expose
the product to rain or moisture, dripping or spraying water. • Do not place any sources of fire on the product, for
example, spark plugs etc. • Do not place the product in places where there is insufficient air circulation. • Do not insert
any objects into the ventilation openings. • Do not interfere with the internal electrical wiring of the product. It may be
damaged and therefore terminate the warranty. The product must only be repaired by a trained specialist. • Use a
moderately moistened cloth for cleaning. Do not use solutions or cleaning products - may damage plastic parts and
electrical wiring • Do not immerse the product in water or other liquids. • Do not repair it yourself if the product is
damaged or defective. Put it in the repair shop where you bought it • The product should not be used by a person
(including children) by physical, sensory or mental disability or lack of experience and knowledge impeded by the safe
use of the device if they are not controlled, or if they were not informed by the person responsible for their safety about
the use of the device • Children's control is necessary to ensure that they do not play with the device.
Declaration of conformity has been issued for the product. This and other documentation is available on the website
www.sen-controls.eu.
Producer of this product is SASWELL CONTROLS (HONGKONG) LTD.
Importer and distributor for Saswell is Sen Controls d.o.o., Belokranjska cesta 29, 8340 Črnomelj, Slovenia

14
Features
•LED indicators for display
•IP21 protection
Specifications
•Power supply 100-240V AC, 50/60Hz
•Communication: Wireless, RF, frequency 868MHz (FSK), range up to 100m
•Accuracy ± 1°C
•Ambient temperature 0°C ~50°C
•Warehouse temperature -10°C ~ +60°C
•Dimensions 113 x 83 x 30mm

15
3
4
5
Description of the receiver and its functions
Receiver description
6. Screw for opening the housing
7. Main and the only button on the receiver
8. LED indicator A (green / red LED)
9. LED indicator B (green LED)
10. LED indicator C (yellow LED)
Button description, turning the receiver ON and OFF
The device has only one button and with this button you control all of the
functions of the device. The primary function of the button is of course for
turning the device ON and OFF. You can do this by shortly pressing on the
button. If the receiver is connected to a power source and the receiver is
turned off, none of the LED indicators should be lit. When the receiver is
turned on, LED indicator A is always lit.
Need for heat
When the thermostat gives the command for heating, the thermostats LED
indicator B goes lit. When there is no more need for heating, the LED
indicator B turns off.
Communication between the devices, Connection TEST
When the thermostat is communicating with the receiver or vice versa, the LED indicator C blinks twice. This is also the
way to test if the communication between the devices is working as for example, if you increase or decrease the
temperature on the thermostat, the receiver should confirm the order by blinking LED indicator, as described.
1
2

16
Forced output mode
Receiver has an option to manually activate the forced output mode, which forces the output to be always turned on.
The receiver then ignores any communication made by the thermostat and the mode is activated until you manually
deactivate it. This mode is useful if the thermostat is malfunctioning and you need to get the heating started or in any
other situation.
You can activate this mode by first turning off the thermostat so that no LED indicators are lit. Now hold the button for
around 8 seconds. The LED indicator C turns on after 3 seconds but ignore this and keep holding the button until LED
indicators A and B are the only ones lit GREEN. The function is now on. You can turn off this mode with a short press
on a button.
Setting the heating temperature limit (electrical floor heating)
The receiver has an option to set the highest heating temperature when using electrical floor heating. This mode is only
available if you’re using an external floor sensor plugged in the receiver. Sensor has to be NTC 100K.
To turn on this mode, you have to install the floor sensor and turn on the receiver, so that LED indicator A is lit (red).
Now hold the button for 3 seconds and LED indicator A (red) will now turn off and start blinking green. Now, with
pressing the button, you change the LED indicators that are lit and with that the temperature limitation.
If LED indicators are lit:
- LED A and LED B (both green) : temperature limitation will be set to 30°C
- LED A (green) and LED C (yellow): temperature limitation will be set to 40°C
- LED A (green), LED B (green) and LED C (yellow): temperature limitation will be set to 55°C
- blinking LED A (green) : temperature limitation is not set
To exit and save the settings, hold the button for 3 seconds.

17
Connecting (pairing) the thermostat and the receiver
If you’ve purchased the receiver and the thermostat together, then they should already be paired. Follow these
instructions if that is not the case of if you need to pair them again.
Turn off the receiver, so that none of the LED indicators are lit. Now hold the button for 3 seconds, so that LED
indicator C (yellow) will be lit. Now the receiver is ready for pairing and waiting for the thermostat.
Now, follow the instructions for pairing in the thermostats manual. When the pairing is complete, usually the
thermostats LCD displays “1” and the receivers LED indicator C blinks 5 times and then turns off.

18
Receiver installation and electrical wiring
Receiver installation
Open the receivers housing by unscrewing the screw on the top of the case (1). Now carefully open the housing from
the front side (2). Install the housing on a wall with included screws. (3). Now, do the electrical wiring. After you’ve
connected all the wires, close the housing and put the top screw back in its place (4)
Tip: Do not mount the receiver on a metal surface, very close to metal objects and other electrical devices, as there
can be interference in wireless communication between the receiver and the thermostat. Also, the RF 100m range is
defined as theoretical nature, and in practice this is influenced by a huge number of factors (from type of house, other
wireless devices, electrical appliances, …) so be careful to mount the receiver in a position where it can normally
communicate with the thermostat. The devices uses top quality electrical elements but yet, we cannot influence on all
factors.

19
Electrical wiring
Again, before proceeding to electrical wiring, make sure that you’ve read all of the safety warnings, instruction manuals
of all devices around and turn off the main power switch in your house. Installation should be carried out by a qualified
and trained person!
Scheme:
L – Line
L1 – User Line
N – Neutral
N1 – User Neutral
NC – Normally Closed contact
NO – Normally Open contact
COM – Common wire (contact)
S1, S2 – Sensor contacts for underfloor heating (NTC 100K)*
* - Contacts not in function and are disabled.