SatKing DVBS-100HD User manual

SatKing DVBS-100HD
Instruction Manual

- 1 -
SAFETY
Safety Precaution
The IRD is complied with international safety standards. Please read these simple
guidelines carefully before using this device.
Power Supply
90–250V AC 50/60Hz.
Do Not Dismantle
Do not attempt to dismantle the IRD. Opening the cabinet may cause malfunction
or electric shock.
Avoid Overloading
Do not overload a wall outlet, extension cord or adapter as this may result in fire
electric shock.
Avoid Extreme Humidity
Do not install the IRD in an extreme humid place. The STB shall not be exposed to
dripping or splashing and that no objects filled with liquids, Such as vase, shall be
placed on the apparatus.

WARNING: To prevent fire or shock hazard, do not expose this
appliance to rain or moisture.
NOTE: If not used for long, please remember to pull out the power cable
or turn off the power.

- 2 -
CLEANING
Disconnect the STB from the wall outlet before cleaning. Use dry cloth to Dust the
STB.
Avoid Object and Liquid Entry
Do not insert any kinds of small objects, such as a coin, into the IRD as it may
result in short circuit.
Ventilation Openings and Installation
The IRD ’S ventilation openings prevent itself from overheating. Do not block them
as it may cause malfunction. Put the IRD on a firm and flat surface. Avoid extreme
heat and direct sunlight.
Power supply
Do not defeat the safety purpose or the polarized or grounding-type plug. If the
provided plug does not fit into your outlet consult an electrician for replacement of
the obsolete outlet. Protect the power cord from being walked on or pinched
particularly at Plugs, convenience receptacles, and the point where they exit from
the apparatus.
Location
Place the STB indoor in order not to expose to lightening, rain or sunlight. Unplug
this STB during lighting storms or when unused for long periods of time.
Maintenance
Use spare parts and accessories only from the original manufacturer.
Service
Refer all servicing to qualified service personnel. Servicing is required when the
STB has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been soiled or objects have fallen into the STB, the STB has
been exposed to rain or moisture, does not operate normally, or has been
dropped.

- 3 -
CONTENTS
HOW TO USE THIS MANUAL
This manual provides complete instructions for installing and using this receiver.
SAFETY INSTRUCTIONS
1．Before You Begin
1.1 Features .........................................................................................................4
1.2 Accessories....................................................................................................4
2．Controls and Functions
2.1 Front Panel.....................................................................................................5
2.2 Remote Control Unit ......................................................................................6
2.3 Rear Panel (The actual production will have difference.) ..............................7
3．Connections
3.1 Connecting to TV ...........................................................................................8
3.2 Connecting to Dish.........................................................................................8
4．Setting and Operations
4.1 Before Setting ................................................................................................9
4.2 Setting ............................................................................................................9
4.3 System .........................................................................................................12
4.4 Setup............................................................................................................14
4.5 Edit Channels...............................................................................................16
4.6 Program Guide.............................................................................................17
4.7 PVR Functions .............................................................................................18
4.8 TV menu at the normal mode ......................................................................20
Appendix
A1 Trouble Shooting ..........................................................................................21
A2 Specifications................................................................................................22
A3 Glossary of Terms.........................................................................................24
Please Note: The Remote Control Unit and STB may be changed
without notice in advance. So this manual may be different in some
ways. In this case, please refer to the product.

- 4 -
1. Before You Begin
1.1 Features
1.1.1 Common Part
zEasy Graphic MENU Interface
zSupports DiSEqC 1.0/1.2,13/18V, 22Khz Tone
zRCA Connector
zMulti-language Function (Menu, Audio)
zLast Channel Memory
zOSD: Transparency &Blending, 256 Palette Colors
zFront Panel Buttons &IR Remote Controller User Interface
zEditing Functions (TV or Radio Channel, Channel Name, Favorite Name, Satellite
Name)
zEPG for On Screen Channel Information
zChannels Memory for Multi-satellite
zOperation Modes (Digital TV, Digital Radio, Favorite)
zPLL RF Modulator UHF 21-69 with PAL G/I/K and NTSC-M
1.1.2 Digital Part
zReceives QPSK Satellite Broadcasting RF Signal and Decodes the Digitally
Encoded Signal
zDigital Tuner with Loop-through out
zSCPC/MCPC Receivable from C/KU-band Satellite
zMPEG-2 Main Profile at Main Level
z4000 Channels Memory
1.2 Accessories
zUSER ’S MANUAL
zREMOTE CONTROL UNIT
zRCA VIDEO/AUDIO CONNECTOR
zBATTERIES
Warning:
Please don’t recharge, disassemble, electric, and mix with used or other battery
types.

- 5 -
2. Controls and Functions
2.1 Front Panel
zDisplay (4-digits 7-segments / 2LED)
The 4-digits displays channel information. The green LED lights up when the
channel is locked in.
zCH▲/CH▼
Move the cursor up/down in Menu state. Change the current program to the
previous/next program in No-Menu state.
zVOL◄/ VOL►
Moves the cursor left/right in Menu state. Change the volume in No-Menu state
zMENU
Press to display the Main Menu.
zOK
Press this button after your selection or correction.
zSTANDBY
Switch between Operation and Standby modes.

- 6 -
2.2 Remote Control Unit
All features of the set-top box can be controlled with the remote controller.
z: Press to switch between Operation and Standby modes.
zMUTE : Press to temporarily cut off the sound.
zNUMBER BUTTONS (0~9): Press to input Channel, Password, PID code and etc.
zTV/RADIO: Press to select the TV/RADIO mode.
zRECALL: Press to return to the previous channel.
zPAGE +/ PAGE -: Page up/down in the channel list.
zFAV: Press to display Favorite Channel Mode.
zEPG: Press to display the Electronic Program Guide.
zSAT: Press to display the satellite list menu.
zi: Display the information of the current program.
zVOL◄/ VOL►: Adjust volume or move cursor in the menu.
zCH▲/CH▼: Change Channel or move cursor in the menu.
zOK: Press to select the item in the menu, or list the TV or Radio channels.
zEXIT: Press to return to the previous menu or escape from the current mode.
zMENU: Press to display the Main Menu.
zAUDIO: Press to select different audio mode.
z9PIC: Press to display mosaic screen of programs.
zLANG: Press to display the Audio Select Menu.
zPAUSE: Pause the video output of receiver.
zTEXT: Graphic information function.
zTV/SAT: Press to switch between TV or AV mode.
zZOOM: Zoom on a part of the picture during normal viewing mode.
zPVR LIST: Press to enter Recorded list.
z◄◄: Fast reverse. Play the recording at increased speed. By pressing the button
multiple times you select from eight different speeds.
z►►: Fast forward (refer to ◄◄)
z►: Starts playback at the beginning of the current record session or returns to
normal playback speed from fast reverse/forward or pause.
z●: Start recording.
z∣
/ ∣: Skip to the previous or next program.
z∣∣: Pauses the playback.
z■: Stops the playback.

- 7 -
2.3 Rear Panel (The actual production will have difference.)
zRS232 Serial Port
For firmware update, serial communication port (RS-232).
zLNB IN
Connect the digital signal from your LNB of your satellite dish to this connector.
zLNB OUT
Give you the possibility to connect an extra receiver (analogue or digital).
zUSB
Provide for the mobile storage.
zYPbPr
Connect component video to HD Monitors (YPbPr Type).
zVIDEO (Yellow RCA)
This connector has a constant video signal for additional VCR-connections.
zAUDIO Right/ Left (Red /White RCA)
These connectors give you the possibility to connect the audio signal to an
external amplifier, or the audio input of your TV.
zSPDIF OUT (Optical)
Connect to an External Audio Amplifier with S/PDIF Optical Digital Audio.
zHDMI Connector
Connect High-Definition Multimedia output to HD Monitors (HDMI Type).
zLAN
Connect to internet.
zPOWER
Turn the receiver’s power on or off. Your receiver requires a current of 90~250V
AC (Auto-selectable), 50/60Hz.Make sure to check the power specification before
connecting your receiver to the wall outlet.

- 8 -
3. Connections
3.1 Connecting to TV
zConnect the satellite signal from the LNB to the LNB IN connector.
zConnect the RCA connector at the back of the receiver to the RCA-in connector
on your TV set.
3.2 Connecting to Dish
zConnecting a fixed satellite dish to your receiver
Make your choice of which satellite you want to receive your signals from, and
have your dealer aim your dish at the requested satellite. Connect a coax cable to
your LNB and the other end directly to the LNB IN connector of your receiver.
zConnecting multiple fixed dishes to your receiver using a DiSEqC 1.0 switch
If you want to watch programs from more than satellites (For in instance from
Astra and from Hot Bird) it is advisable to use fixed dishes and a DiSEqC 1.0
switch. Connect the OUT connector of the DiSEqC 1.0 switch to the LNB IN
connector at the back of your receiver.
zConnecting a dish on a motorized positioner to your receiver
Another possibility to watch programs from multiple satellites is by mounting a dish
to a motorized DiSEqC 1.2 positioner. Connect the LNB with a coax cable to the
LNB IN connector of the positioner, and connect the OUT connector of the
positioner to the LNB IN connector at the back of your receiver.