Satlink ST-5150 User manual

ST-5150
R
SATELLITE FINDER
User's Manual

English
CONTENTS
1. GUIDE........................................................................................................1
1.1 IMPORTANT SAFETY INSTRUCTIONS................................................... 1
1.2 UNPACKING................................................................................................... 1
1.3 PRODUCT OVERVIEW& ILLUSTRATION.............................................. 2
2. OUTLINE ..................................................................................................5
3. THE MENU OSD INSTRUCTION .............................................................6
3.1 DVBS2...........................................................................................................6
3.2 DVBT2 ...........................................................................................................9
3.3 DVBC............................................................................................................12
3.4 LOOP SEARCH ............................................................................................13
3.5 ANGLE CALCULATION..............................................................................13
3.6 OTHERS.........................................................................................................13
3.7 MULTIMEDIA ...............................................................................................17
3.8 SYSTEM SETTING ..................................................................................... 18
4. TECHNICAL SPECIFICATION ............................................................... 20
5. TROUBLE SHOOTING ...........................................................................23

1
English
1. GUIDE
1.1 IMPORTANT SAFETY INSTRUCTIONS
Thank you for choosing our product. Before installation, we
would like to remind you some notes, which is very important
for operating safely and properly, as follows:
• Be sure to read this user manual before starting your
operation.
• You must install the dish with correct direction and angle. If
the dish is not working properly, contact your local dealer.
• When the unit is suddenly moved to a hot area from a cold
area, it may cause some problems. In that case, turn o the
power, and turn on again after 1-2 hours.
• Keep meter placed in clean space with sucient ventilation.
• Do not cover the meter with or place it on a unit that emits
heat.
• Clean the case by a soft cloth with a little washing liquid.
• Do not remove the cover.
• Do not let the unit exposed to extreme heat, cold or humid
conditions.
• No liquids or any other materials to come inside of the unit.
1.2 UNPACKING
Open the package and make sure it includes all below items, if
any missing,please contact the reseller for replacement.
1. Digital Satellite Meter 4. Power adaptor
2. User’s manual 5. DC 12V connect line
3. AV cable 6. BNC-Connector
NOTE: Please refer to our actual configuration.

2
1.3 PRODUCT OVERVIEW& ILLUSTRATION
NO Description FUNCTION
1 Turn on/o meter
2Power Power indicator light
3 22kHz 22kHz indicator light
4H/V
Vertical /Horizontal
polarization voltage output
light
5 LOCK Signal lock indicator light
6 Charge Charger indicator light
7 MENU
Show the main menu on
the screen or jump back to
previous menu in sub-menu
setting conditions
8 EXIT Exit out form present menu
and save the settings
9 SCAN Shortcut key for DVB-S2
menu
10 MUTE MUTE
11 INFO Channel information

3
English
NO Description FUNCTION
12 AV-S AV IN/OUT switch key
13 F1 Auxiliary function key
14 Turn on/o Torch
15 AUDIO Audio type selection / Red
key
16 SAT Shortcut key for
Sat Installation menu
17 T V/R TV/Radio switch key
18 SYS Shortcut key for System
Setting menu
19 Compass Mechanical compass
20 NAVIGATION KEY
Volume Control or move
cursor, channel or change,
confirm etc
21 0-9
Number key to
select channels or enter
programming
22 RF Connect to satellite antenna
cable
23 ANT Connect to antenna
24 DC OUT DC 12V output for extern
equipment
25 HDMI HDMI output port
26 AV OUT AV output port
27 AV IN AV input port
28 LED Torch

4
NO Description FUNCTION
29 USB
USB port for software
upgrading or multimedia
playing
30 DC IN Connect to power adaptor
31 Battery Battery
32 Speaker Speaker integrated

5
English
2. OUTLINE
•4.3 Inch High Definition TFT LCD Screen
•Fully DVB-S/S2/T/T2/C compliant
•MPEG2, MPEG4, H.264/MPEG4 AVC, H.265/HEVC hardware
decoding
•Digital meter for signal strength and quality
•Supports Auto Scan and Manual Scan
•Sound and Light Alarm for Locking Signal
•Auto Calculate Angle of AZ ,EL
•Supports DISEQC 1.0/1.1/1.2, Unicable, 0/22kHz Tone
•Speaker Integrated
•Support both AV out and AV in
•Support HDMI out
•LNB short protect
•7.4V/2600mAh LiIon Battery Included
•Software upgrade via USB port
•Easy to carry

6
3. THE MENU OSD INSTRUCTION
If you have installed and connected the cables to the finder,
pressing MENU to display the Main Menu.
• DVB-S2
• DVB-T2
• DVB-C
• Loop Search
• Angle Calculation
• Others
• Multimedia
• System Setting
Press the keys of YZAB to move the cursor up or down in
the menu interface, then use OK to confirm a selection.
3.1 DVB-S2
Select DVB-S2, then press OK into the Satellite Find Setup.

7
English
3.1.1 SATELLITE
Press AB key into the satellite list. Use YZ key to move the
cursor, then press OK to select the satellite you want.
3.1.2 LNB TYPE
There are 4 types you can select: C Band/Ku Band/Unicable I/
Unicable II.
3.1.3 LNB FREQUENCY
Press AB key to switch LNB frequency you want.
3.1.4 TRANSPONDER
Press AB key into the TP list. Use YZ key to move the cursor
then press OK to select the TP you want.
3.1.5 FREQUENCY
Frequency of the current transponder, input the value by using
the number keys.
3.1.6 SYMBOL RATE
Symbol rate of the current transponder, input the value by
using the number keys.
3.1.7 3.1.7 POLARISATION
Press AB key to change vertical or horizontal of polarization.
3.1.8 22KHZ
Press AB key to turn on or o 22kHz TONE Switch.

8
3.1.9 DISEQC MODE
Press AB key to set the type of port as None/DiSEqC1.0/1.1.
3.1.10 DISEQC TYPE & INPUT
In C/Ku Band mode:
we can press AB key to set DiSEqC 1.0/1.1 as A/B port, and set
Tone Burst Mode as NONE/Tone Burst A/B.
In Unicable mode:
we can press AB key to switch IF Index from 1 to 8, or use
number key to modify IF Freq, and then press AB key to select
A/B as Sat Position.
3.1.11 LNB POWER
Press AB key to Switch LNB Power ON/OFF.
3.1.12 BEEP TONE
Press AB key to Switch beep tone ON/OFF. If we open it, the
beep of lock alarm will open when we enter into the search
screen.
3.1.13 QUICK SEARCH
When parameters have been
set done, press OK into quick
search. There will have some
signal information displayed
on the screen.Press YZ key
to change transponder.

9
English
• Scan: Press the ENTER key to
search the current TP.
• Auto Scan: Press the red
key to auto blind search the
current satellite.
3.2 DVB-T2
Select DVB-T2, then press OK
into the Scan Setup.
3.2.1 COUNTRY
Press AB key to change the default country.
3.2.2 CHANNEL NO
Press AB key to change the channel number.

10
3.2.3 FREQUENCY
Frequency of the current channel, input the value by using the
number keys.
3.2.4 BANDWIDTH
Press AB key to change the bandwidth, we can select 5, 6, 7
or 8M.
3.2.5 MODE
Press AB key to change the DVB standard, we have there
types including T/T2/T+T2, you can select one you want.
3.2.6 ACTIVE ANTENNA
Press AB key to switch antenna power ON/OFF.
3.2.7 LNB POWER
Press AB key to change the antenna power, there are 3 types
including 5V/12V/24V.
3.2.8 LCN
Press AB key to switch LCN ON/OFF.
3.2.9 BEEP TONE
Press AB key to Switch beep tone ON/OFF. If we open it, the
beep of lock alarm will open when we enter into the search
screen.

11
English
3.2.10 QUICK SEARCH
When parameters have been
set done, press OK into quick
search. There will have some
signal information displayed on
the screen.
• Scan: Press OK or red key to
search current channel.
• Auto Scan: Press green key
to auto search the current
channel.
• S/Q: Press blue key to enlarge
showing of the signal strength
and quality.

12
3.3 DVB-C
Select DVB-C, then press OK
into the Scan Setup.
3.3.1 COUNTRY
Press AB key to change the default country.
3.3.2 CHANNEL NO.
Press AB key to change the channel number.
3.3.3 FREQUENCY
Frequency of the current channel, input the value by using the
number keys.
3.3.4 STANDARD
There are 2 types of standard you can select: J83.A/C and J83.B.
3.3.5 BEEP TONE
Press AB key to switch beep tone. If we open the it, the beep
of lock alarm will open when we enter into the search screen.
3.3.6 QUICK SEARCH
Please refer to 3.2.10.

13
English
3.4 LOOP SEARCH
We can see 8 TP or channels
when we enter into this
interface, and press OK to edit.
There are 3 modes we can
choose: DVB-S2,DVB-T2 and
DVB-C. Press the red key
to change.
It will finish loop search after
edition, then singal strenth and
quality of each TP or channel
will be displayed on the screen.
3.5 ANGLE CALCULATION
Input satellite longitude, local
longitude and latitude by
number key, and device will
calculate the polarization angle,
azimuth and elevation on the
top of the screen.
3.6 OTHERS
• Channel Manager
• Satellite List
• Transponder List
• Motor Setting
• EPG

14
3.6.1 CHANNEL LIST
• SAT
Press F1 key to
switch dierent channel list.
• Lock
Press YZ key to
select programs we want to lock, then press the red key to
lock them.
• Del
Press the green key to delete current channel.
• Move
Select a channel first, then press the orange key to move to
other position.
• Edit
Press the blue key to confirm channels which need operating.
3.6.2 SATELLITE LIST
All the satellite will be
displayed on the screen.

15
English
Press the red key to add a new
satellite.
Press the green key to edit
current satellite.
Press the orange key to delete
current satellite.
Press the blue key to scan
current satellite.
3.6.3 TRANSPONDER LIST
All the transponders under the
current satellite will be displayed
on the screen, and press AB
key to switch satellite.

16
Press the red key to add a
new transponder.
Press the green key to edit
current transponder.
Press the orange key to
delete current transponder.
Press the blue key to scan
current transponder.
3.6.4 MOTOR SETTING
There are 5 modes in motor setting:
• USALS
Controling motor according to your local position, you can
modify it in Angle Calculation.
• DiSEqC 1.2
There are 64 position you can select to move motor.
• Set East Limit
Move motor to east.