SATO CL4NX Plus User manual

First edition: Feb. 2020 Q05346500
©2020 SATO Corporation
Rotary Cutter Kit
Installation Manual
Accessories
This Installation Manual explains how to install Rotary Cutter Kit (hereafter referred to as
“the product”). Read the restrictions and precautions when installing.
For details on how to use Rotary Cutter Kit and how to use and operate CL4NX Plus setting
items, see CL4NX Plus web manual “Operator Manual”.  



Cutter unit
Bracket
Cutter cable
Cover
Relay PCB
Installation Manual (this document)
Screws
Screws for xing the Relay PCB (2 pcs)
Screws for xing the bracket (3 pcs)
Screws for xing the cutter unit (2 pcs)
Black screws for xing the cover (2 pcs)
Required tool
• Phillips screwdriver (JIS #2 or equivalent)
Installing the Cutter Unit
1 Make sure that the CL4NX Plus is powered off and disconnect the
power cord from the AC outlet.
2 Open the top cover and push the
head lock lever towards the rear
to unlock the print head.
Tip
Open the top cover fully to prevent
accidental drop of the cover.

Website http://www.satoworldwide.com/
Safety Precautions
This section describes how to use the product safely. Be sure to read the following information
carefully before using the product.
Pictographic Symbols
This installation manual uses a variety of pictographic symbols. These symbols emphasize the
safe and correct use of the product and to prevent injury to others and property damage. The
explanation of the symbols is as follows. Be sure to understand these symbols well before you
read the main text.
WARNING Ignoring the instructions marked by this symbol and erroneously
operating the product could result in death or serious injury.
CAUTION Ignoring the instructions marked by this symbol and erroneously
operating the product could result in injury or property damage.
Symbol example
The pictograph means “Caution is required”. A specic warning symbol is
contained inside this pictograph.
The pictograph means “Should not be done”. What is specically prohibited is
contained in or near the pictograph.
The pictograph means “Must be done”. What is specically to be done is
contained in the pictograph.
WARNING
Do not place in high-temperature locations
Do not place the product near heating equipment such as cooking appliances or
a heater, or in high-temperature locations. Doing so could damage the product or
result in a re or electric shock.
Connecting cables or optional devices
• When connecting a cable or optional device to the product, be sure to turn off
each of the devices. If they are connected with the power on, an optional device
could move unexpectedly, resulting in injury, electric shock, or damage.
• When installing a cable or optional device, be sure not to make a mistake in the
orientation and steps to install. Otherwise, it could result in injury, re, electric
shock, or damage.
• Do not use cables other than the ones supplied with the product or recommended
by us. Doing so could result in smoke, re, electric shock, or damage.
WARNING
Do not operate with wet hands
Do not power on/power off the product or plug/unplug the power cord and other
cables with wet hands. Doing so could result in electric shock or damage.
Do not touch or insert any object in the cutter
Do not touch the cutter with your hands or insert foreign objects other than media
into the cutter. Doing so could result in injury.
CAUTION
Power cord and other cables
• Grab a power cord and other cables by the plug when removing from the outlet
or connector port. Removing a power cord and other cables by grabbing the
cord/cable area could result in exposure of wires, breakage, re, electric shock,
or damage.
• Do not place the power cord and other cables near a heater or other sources
of heat. Doing so could result in melting of the power cord and other cables
sheathing, re, electric shock, or damage.
Handling
Some parts of the product are sharp. Be careful not to get injured.
Precautions on Installation and Handling
• For details on the restrictions and precautions on installation of CL4NX Plus, see the CL4NX
Plus web manual “Operator Manual”.
• The product works with 1.12.0 version rmware build or later. Check the rmware version
shown on the [Information] Menu > [Build Version] screen of CL4NX Plus. Contact your
SATO reseller or technical support for availability of the latest rmware.

3 Remove the front covers of CL4NX
Plus.
Remove the two screws.
Slide out in the direction of the arrow to
remove the right and left front covers.
4 Connect the relay PCB to the CL4NX Plus and x it with screws .
Discharge static electricity through a metal object before touching the relay PCB.
Failure to do so can damage the relay PCB.
Pull out the option cable from the CL4NX Plus.
Attach the supplied cutter cable to the relay PCB.
Attach the option cable pull out from the CL4NX Plus to the relay PCB.
Tip
If the option cable has a heat shrink tube, remove the heat shrink tube rst.
Be sure not to cut or damage the cable when you cut the heat shrink tube.
Insert the relay PCB with the cables attached in to the CL4NX Plus as shown in the figure.
Option cable
Relay PCB
Cutter cable



Screw onto the board in two places.
5 Attach the bracket to the CL4NX
Plus with screws (three places).
6 Connect the cutter cable of the
relay PCB to the cutter unit.
Tip
If it is difcult to connect
the cutter cable, remove
the protective cover. After
connecting, be sure to
reattach the protective cover.
7 Align the cutter unit and x it with
screws .
As shown in the figure, pass the cables through
the groove of the bracket and press lightly.



Option cable
Screw
Screw
Bracket
Screw
Cutter cable
Cutter cable
Protective
cover
Cutter unit
Cutter unit
Cutter
cable
Insert the projection of the cutter unit into the hole of the bracket attached to CL4NX
Plus to locate the cutter unit to the appropriate position.
Make sure there is no gap
between the CL4NX Plus and the
cutter unit.
Hole of the
bracket
Hole of the
bracket
Projection
Projection
Fix the cutter unit in four places with two screws and two other screws of the cutter unit.
Screw
Screw
Screw
of the
cutter
unit
Screw of
the cutter
unit
Screw
8 Attach the cover.
Hook the right side of the cover onto the CL4NX Plus.
Push the left side of the cover toward the CL4NX Plus.
Slide the cover to the left.
Hook onto the CL4NX Plus


Secure the cover with the two screws .
Conguring CL4NX Plus
To print using the cutter, select [Cutter] or [Cut & Print] on the [Print Mode] menu of the CL4NX
Plus.
See the CL4NX Plus web manual “Operator Manual” for details.
Screws