Twothousand TT-F65 User manual

VEGETABLE CUTTING MACHINE
OPERATION MANUAL
TT-F60 / TT-F65
TT-F60
TT-F65

1. GENERAL PROFILE
1.1. DESCRIPTION
E VEGETABLE CUTTER MACHINE CAN SLICE, SHRED, GRATE,
ITH ITS RANGE OF HIGH OUTPUT CUTTERS, THE MACHINE IS IDEAL FOR
.2. GENERAL PRECAUTIONS
THE MULTI-PURPOS
CHIP AND DICE VARIOUS FOODSTUFFS ( FOR THE PREPARATION OF RAW AND
COOKED VEGETABLES, FRUITS AND CHEESES ).
W
RESTAURANTS, LARGE OPENING KITCHENS, INSTITUTION AND SMALL
COMPANIES.
1
THE VEGETABLES CUTTING MACHINE MUST BE MANAGED BY SKILLED
gI THE PERSONNEL , VOCATIONAL TRAINING IS
gACHINE COMES WITH SEVERAL SAFETY SYSTEMS, AVOID SETTING
g, CHECK TO MAKE
gNDITIONS.
DPARTS
gE
2. TECHNICAL FEATURES
g
PERSONNEL, FAMILIAR WITH THE INSTRUCTIONS FOR USE AND SAFETY
CONTAINED IN THIS MANUAL.
N THE CASE OF ROTATION OF
NECESSARY.
EVEN IF THE M
THE HANDS NEAR THE CUTTING DISCS AND MOVING PARTS.
BEF ORE ANY CLEANING AND MAINTENANCE OPERATIONS
SURE THE MACHINE IS DISCONNECTED FROM THE MAINS.
PERIODICALY CHECK CABLES AND ELECTRIC ELEMENTS CO
gDO NOT USE THE MACHINE TO CUT FROZEN FOODS. REMOVE ALL HAR
FROM FOODS BEFORE CUTTING TO AVOID DAMAGING THE CUTTING BLADES.
NEVER REPLACE PARTS OF THE MACHINE BY YOURSELF, BUT APPLY TO TH
ASSISTANCE SERVICE.
.1. SPECIFICATION SHEET2
MODEL WEIGHT
KG.
POWER
WATTS
ELECTRICAL RPM
DISC
TT-F6024.5
TT-F65
DIMENSIONS
CM.
50X25X46
50X25X47 26
550W or 750W
for your choice
300 RPM
CONNECTION
230V/1/50Hz
115V/1/60Hz
380V/3/50Hz

2.2. SUPPLY CONDITIONS AND DISPOSAL OF PACKINGS
HE CUTTING MACHINE IS PACKED IN A STURDY CARDBOARD BOX WITH
HE EQUIPMENT INCLUDE:
AND MAINTENANCE
COMPONENTS (CARTON, FOAM, STRAPS, AND SO ON) CAN
3. INSTALLATION
T
INTERNAL SHAPED EDGES WHICH GUARANTEE THE PERFECT INTEGRITY OF THE
MACHINE DURING TRANSPORT.
T
gINSTRUCTIONS FOR USE
gEJECTING DISC
ALL THE PACKING
EASILY BE DISPOSED OF AS HOUSEHOLD RUBBISH
3.1. SETTING THE MACHINE
HE MACHINE CONNECTION AND THE SETTING AT WORK MUST BE MADE BYT
SKILLED PERSONNEL.
WARNING: BOTH THE SYSTEM AND LOCATION WHERE THE EQUIPMENT HAS TO BE
RESPONSIBILITY FOR DIRECT
ED, DRY AND FIXED FACE, FAR FROM
.2. ELECTRIC CONNECTIONS
SET MUST COMPLY WITH THE REGULATIONS FOR THE ACCIDENT PREVENTION
AND ELECTRICAL REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ANY AND ALL
OR INDIRECT DAMAGES WHICH MAY ENSUE FOR NON-COMPLIANCE WITH
THE ABOVE MENTIONED REGULATIONS.
SET THE EQUIPMENT ON A WIDE, LEVELL
HEAT SOURCES AND WATER SPRAYS.
3
HE EQUIPMENT IS SUPPLIED WITH AN ELECTRIC CABLE TO BE CONNECTED TO A
HE
HE MANUFACTURER DECLINES ANY AND ALL RESPONSIBILITY FOR DIRECT AND
MANUFACTURED INTO SINGLE-PHASE V.220/1/50 HZ OR
T
MAGNETO-THERMIC MAIN SWITCH WHICH STOPS THE MACHINE WHEN THE
OPERATOR COMES IN FORTUITOUS CONTACT WITH THE ROTATING ELEMENTS.
IT IS IMPERATIVE THAT THE EQUIPMENT IS WELL GROUNDED ACCORDING TO T
REGULATIONS IN FORCE.
T
INDIRECT DAMAGES WHICH MAY ENSUE FOR NON-COMPLIANCE WITH THE
REGULATIONS IN FORCE.
THE CUTTING MACHINE IS
V.115/1/60HZ. WHENEVER THE VOLTAGE DIFFERS FROM THE ABOVE MENTIONED,
PLEASE APPLY TO THE MANUFACTURER, OR THE AUTHORIZED DISTRIBUTOR.

3.3. SAFETY MEASURES AND TRAINING THE FINAL USER
THE SKILLED PERSONNEL IN CHARGE OF THE INSTALLATION AND ELECTRIC
CONNECTIONS OF THE EQUIPMENT IS RESPONSIBLE OF THE TRAINING OF THE
FINAL USER, WHICH MUST ALSO BE INFORMED ON THE SAFETY MEASURES TO
COMPLY WITH. THIS INSTRUCTION MANUAL COMES WITH EACH EQUIPMENT.
4. USE OF THE EQUIPMENT
4.1. CONTROLS
THE CONTROLS AND PILOT LIGHT ARE LOCATED IN THE FACE OF MIDDLE
ALUMILIUM BASE.
1. GREEN BUTTON FOR STARTING THE MACHINE
2. RED BUTTON FOR STOPPING THE MACHINE
THREE-PHASE CONNECTION SINGLE-PHASE CONNECTION
L1
L2
L3
L1
L2 L1 L1
L2
L1
L2
4.2. SETTING THE DISCS ON THE MACHINE
LIFT UP THE LOCKING HANDLE AS SHOWN IN FIGURE NO. 1 AND OPEN THE COVER.
PUT AWAY THE PLASTIC EJECTING DISC, THEN CHOOSE A DISC OR A DISCS CHOICE
ACCORDING TO YOUR PURPOSE. CLOSE THE COVER. WORK ON THE START
BUTTON TO AUTOMATICALLY HOOK THE DISCS IN THE CORRECT POSITION.

COVER OPENING (1) DISC POSITION (2)
ATTENTION TO DISC BLADES!!
4.3. CHOICE OF THE DISCS
DISC CHOICE FOR VEGETABLE CUTTER MACHINE
PICTURE PART NO. SIZE
G002 2mm
G003 3mm
G005 5mm
G007 7mm
Shredding
G010 10mm
SA002 2mm (three blades)
SA004 4mm (two blades)
SA006 6mm (two blades)
SA008 8mm (single blade)
SA010 10mm (single blade)
Slicer (aluminium)
SA020 20mm (single blade)
SP002 2mm (three blades)
Slicer (plastic)
SP004 4mm (three blades)
J303 3x3mm
J303 4x4mm
Julienne
J303 8x8mm

mz_W_ __
m m
mzXWW XWXW
kz___ ___
kzXWWW XWXWXW
k
kzYWWW YWYWYW
4.4. USE OF THE DISCS
THE UNIT IS SUPPLIED WITH THE EJECTOR FITTED TO THE DRIVE SPINDLE. OPEN
THE COVER LOCK AND LIFT THE COVER FULLY IN ORDER TO REMOVE THE
EJECTOR.
BEFORE STARTING WORK, ALWAYS CHECK THE CLEANLINESS OF THE CUTTING
CHAMBER, THE DRIVE SPINDLE, THE EJECTOR, THE CUTTING DISCS AND THE
GRID.
1) FOR SLICING, SHREDDING AND GRATING
gFIT THE EJECTOR ONTO THE FLAT OF THE DRIVE SPINDLE.
gFIT THE DISC REQUIRED (SLICING, SHREDDING OR GRATING).
-- TURN THE DICS IN A CLOCKWISE DIRECTION TO INSERT THE BAYONET FITTING,
THEN CONTINUE IN THE SAME DIRECTION UN IT L IT REACHES THE PIN.
-- TO REMOVE THE DISC, TURN IT IN THE OPPOSITE DIRECTION AND LIFT IT USING
THE FINGER HOLES AT THE EDGES OF THE DISC.
-- CLOSE THE COVER AND LOCK IT.
2) FOR CUTTING INTO CHIPS OR CUBES
gFIT THE EJECTOR.
gFIT THE GRID INTO ITS HOUSING AND CHECK THAT IT IS SEATED CORRECTLY
(SEATING AREA IS CLEAN). THE UPPER FACE OF THE GRID MUST BE SLIGHTLY
BELOW THE TOP OF THE MACHINE BODY.
gTHEN FIT THE CHOSEN DISC AND CLOSE THE LID.

5. CLEANING AND MAINTENANCE OPERATIONS
5.1. GENERALITIES AND PRODUCTS FOR CLEANING
BEFORE CARRYING OUT ANY CLEANING OR MAINTENANCE OPERATIONS, CHECK
TO MAKE SURE THAT THE MAINS SWITCH BE OFF AND THE SUPPLY PLUG
DISCONNECTED FROM THE MAINS.
ACCURATELY CLEAN THE EQUIPMENT AND THE DISCS EVERY DAY FOR A CORRECT
OPERATION AND LIFE OF THE EQUIPMENT.
THE DISCS, THE GRID FOR CUTTING DICES, AND THE PLASTIC EJECTOR, CAN BE
REMOVED FOR WASHING UNDER A WARM WATER JET.
CLEAN THE MACHINE, AND ABOVE ALL WHERE THE DISCS REST, WITH A CLOTH
OR A SPONGE WET WITH WARM WATER, ACCURATELY REMOVE ALL WASTES TO
PREVENT THE DISCS FROM CHANGING THEIR POSITION.
OPEN THE COVER AND LOOSEN THE 1 PIN AS SHOWN IN FIG.3. REMOVE THE COVER
AND WASH UNDER A WATER JET.
(3)
CLEAN THE SURFACES WITH WATER AND SOUP, ALCOHOL, DETERGENTS WITHOUT
ABRASIVES OR SUBSTANCES BASED ON CHLORINE OR SODA (CHLORINE WATER,
MURIATIC ACID).
NEVER USE ABRASIVES, STEEL WOOL, OR SIMILAR PRODUCTS AS THEY MAY
BRING DAMAGES TO THE PAINT, THE COAT, OT THE MACHINE BODY.
FOR CLEANING, USE NON-TOXIC PRODUCTS AND ONES THAT GUARANTEE THE
BEST HYGIENE.
5.2. OPERATIONS IN THE CASE OF FAILURES
WHEN THE WHITE POLIT LIGHT ON THE PANEL IN ON, BUT THE MACHINE DOES
NOT START, CHECK TO MAKE SURE THAT THE HANDLE AND THE COVER ARE
CLOSED. IN THIS WAY, BOTH THE SAFETY MICROSWITCHES. THE SAFETY
MICROSWITCHES PREVENT THE MACHINE START WHENEVER ALL SECURITIES ARE
NOT ACTIVATED.
IN THE CASE OF FAILURES, DISCONNECT THE MAIN WALL SWITCH AND EITHER
WARN THE MAINTENANCE SERVICE, OR THE SKILLED PERSONNEL.
NEITHER START NOR TAMPER WITH THE EQUIPMENT PERSONALLY.

5.3. MACHINE IDLE FOR A LONG TIME
SHOULD THE MACHINE BE IDLE FOR A LONG TIME, DISCONNECT THE MAIN WALL
SWITCH AND CLEAN
THE MACHINE AND ITS ACCESSORIES ACCURATELY. USE WHITE VASELINE OIL (OR
SIMILAR PRODUCTS)
TO PROTECT ALL THE MACHINE'S ELEMENTS.
THESE PRODUCTS, MAINLY MADE UP OF OILY AND DETERGENT SUBSTANCES, AND
NOW AVAILABLE IN SPRAY CYLINDERS FOR EASY APPLICANT, BESIDES GIVING A
GLOSSY ASPECT TO THE ALUMINIUM MAGNESTISM ALLOY, PREVENT MOISTURE
AND DIRT FROM GETTING INSIDE THE MACHINE, HENCE, ITS CORROSION.
WE ADVISE COVERING THE MACHINE WITH A NYLON (OR SIMILAR) CLOTH.
ILLUSTRATIONS
110V
110V/60HZ
450V/50W
R2
AR
AT
C
R1
C
D
220V
AC 220V/50Hz
AC motor
C
K1
K2 K3
K4
J8
J6
J5
J9
J3
J4
J2
J1 F
VR
T
Control circuit
3-OFF 1-FWR 2-ON 4-GND
electric
on-off
C

380V/50HZ
D
C1
C1
C
B
A
AT
AR
D
C
B
A
380V/50HZ
C1
C1
C2
C2
QA QT
(B)
(A)














































NO.
01
02
04
03
05
06
07
09
10
11
13
14
12
08
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Part Name
Pusher
Bolt
Handlebar
Hopper
Disc
Selective disc
Nut
Cam
Umbrella bolt
Rubber Gasket
On-off switch
Pin
Screw
Hopper lid spindle
Body
Proximity detector
Pin
Strapped wheel
Motor support
Motor
Bottom base
Cross member
Head screw set
Small feeder hopper
Spring
Spindle
Locking handle
Locking bolt
Hook
Lockpin
Ejector
Oil Seal
Bearing
Lid pivot ring set
Central spindle
Key set
Belt wheel
Gear cover
Support bracket
Electric box support
Locking nut
Screw
Electric box
Pad
Screw sets

Bearing
TT-F60














































NO.
01
02
04
03
05
06
07
09
10
11
13
14
12
08
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Part Name
Pusher
Handlebar
Hopper
Disc
Selective disc
Nut
Cam
Umbrella bolt
Rubber Gasket
On-off switch
Pin
Screw
Hopper lid spindle
Body
Proximity detectort

Bracket
Strapped wheel
Motor support
Motor
Bottom base
Cross member
Head screw set
Small feeder hopper
Spring
Spindle
Locking handle
Locking bolt
Hook
Lockpin
Ejector
Oil Seal
Bearing
Lid pivot ring set
Central spindle
Key set
Belt wheel
Gear cover
Support bracket
Electric box support
Locking nut
Screw
Electric box
Pad
Screw sets
Bearing
Pin
TT-F65