Saturn 20HS1500-BK-SV Owner's manual

SATURN 20HS1500-BK-SV
20HS2000-BK-SV
HIGH SPEED
FLOOR MACHINE
OWNER’S/OPERATOR’S MANUAL
WWW.EDIC-USA.COM 2-25-19

2
RECEIVING YOUR EQUIPMENT...................................................................................
WARNINGS AND SAFETY..............................................................................................
ELECTRICAL INFORMATION.......................................................................................
GROUNDING INSTRUCTIONS......................................................................................
MAINTENANCE.................................................................................................................
CORD SAFETY AND STORAGE....................................................................................
CLEANUP AND STORAGE.............................................................................................
MAINTENANCE, CLEANUP, STORAGE.....................................................................
PAD INSTALLATION........................................................................................................
DRIVE BELT ADJUSTMENTS.........................................................................................
MACHINE OPERATION..................................................................................................
MANEUVERING THE MACHINE................................................................................
SERVICING.........................................................................................................................
FINAL ASSEMBLY PROCEDURE..................................................................................
EXPLODED VIEW: BOTH MODELS.............................................................................
1500 RPM MODEL PARTS LIST......................................................................................
2000 RPM MODEL PARTS LIST .....................................................................................
3
3-4
4
4
5
5
5
5
5
6
7
7
7
8-15
16-17
18-20
21-23
TABLE OF CONTENTS

3
RECEIVING YOUR NEW SATURN:
When your package is delivered, check all cartons care-
fully for signs of rough handling. If your SATURN is
damaged, notify the carrier immediately and request an
inspection. Be sure to keep all cartons, packing inserts,
packing lists and carrier’s receipt until the inspector has
veried your claim.
EDIC’s liability ceases when the carrier picks up the ship-
ment. However, our customer service sta will be happy
to furnish any information needed in connection with
the claim and will attempt to expedite a resolution.
PLEASE READ BEFORE OPERATING YOUR
NEW SATURN:
Read the manual carefully and completely before at-
tempting to operate the unit. is manual has important
information for the use and safe operation of the ma-
chine. Keep this manual handy at all times.
is equipment has been engineered and manufactured
to provide excellent performance and service. To ensure
that your equipment will continue to perform as intend-
ed:
• Maintain equipment regularly- following the suggest-
ed maintenance schedule provided.
• Use only original EDIC parts when servicing.
• Operate equipment with care.
If additional information is needed, please contact:
EDIC 800-338-3342
All information and specications printed in the man-
ual are current at the time of printing; however because
of EDIC’s policy of continual product development, we
reserve the right to make changes at any time without
notice.
FAILURE TO COMPLY WITH THE FOL-
LOWING WARNINGS AND INSTRUCTIONS
WILL VOID THE WARRANTY.
WARNING!
• Do not operate the machine unless trained and autho-
rized.
• Do not allow children or untrained adults to operate
this machine.
• Do not leave the machine when plugged in. Unplug
from the outlet when not in use, before servicing, and
when changing the brushes or pads.
• Use indoors only.
• Do not allow to be used as a toy. Close attention is nec-
essary when used by or near children.
• Do not bypass or defeat the safety “lock-out lever.”
• e machine was designed for use as per instruction
and recommendations written in this manual.
• Any deviation from its proper use or purpose and the
consequential damage that may occur is the sole re-
sponsibility of the end user.
• Do not use with damaged cord or plug. If the machine
is not working as it should, or it has been dropped,
damaged, le outdoors or dropped into water, return
it to an authorized service center.
• Do not pull or carry by cord, use cord as handle, close
a door on the cord or pull cord around sharp edges
or corners. Do not run machine over cord. Keep cord
away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Make sure the machine is plugged into an electrical
outlet with the same voltage and frequency rating as
shown on the nameplate of the machine. Do not at-
tempt to plug a 115- volt machine into a 230- volt out-
let.
• Do not immerse or use this machine in standing water.
Such use can cause electric shock.
• Keep the electrical supply cord from contacting the ro-
tating brush or drive block.
• Do not expose machine to freezing temperatures.
• To avoid electric shock, do not expose the unit to rain.
Store indoors only.

4
• Connect to a properly grounded outlet only. See
“Grounding Instructions.”
• Turn o all controls before unplugging.
• When using an extension cord, use a 3 conductor
grounding cord, 12 gauge wire or heavier.
• Do not put any object into openings. Do not use with
any opening blocked. Keep free of dust, lint,
• hair and anything that may reduce air ow.
• Do not operate machine in ammable or explosive ar-
eas.
• All servicing of EDIC’s equipment should be per-
formed by a EDIC authorized service center.
• Keep hair, loose clothing, ngers and all parts of body
away from openings and moving parts.
• Use extra care when cleaning near stairs.
• To reduce the risk of re use only commercially avail-
able oor cleaners and waxes intended for machine
application.
• Risk of explosion - Electrical motors and components
can cause an explosion when operated near volatile
materials and vapors. Do not use this machine near
ammable materials such as solvents, thinners, fuels,
grain dust, etc.
ELECTRICAL - 115 Volt
Model: ALL LISTED ON COVER WITHOUT “-220V”
is machine is designed to operate on a standard 15
amp, 120 volt, 60 Hz, AC circuit. Voltages below 105 volt
AC or above 125 volts AC could cause serious damage to
the motor.
ELECTRICAL - 240 Volt
Model: ANY MACHINES WITH A “-220V” AT THE
END OF MODEL NUMBER
is machine is designed to operate on a standard 8.3
amp type L fused 230 volt, 50 Hz, AC circuit. Voltages
below 200 volt AC or above 250 volts AC could cause
serious damage to the motor.
GROUNDING INSTRUCTIONS:
is piece of equipment must be grounded. Should an
electrical malfunction occur, grounding provides a path
of least resistance for electrical current- reducing the risk
of electric shock. is piece of equipment is furnished
with a cord that has a grounding conductor and ground-
ing plug. e grounded plug must only be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordi-
nances.
WARNING:
Connecting the equipment to an improperly grounded
outlet can result in an increased risk of electric shock. A
qualified electrician should be consulted if you are unsure
that the outlet is properly grounded. Do not modify the
plug provided with the equipment. If it will not fit the
outlet, have a proper outlet installed by a qualified electri-
cian.
is appliance is designed for use on a 120-volt circuit.
e grounding plug provided looks like the plug illustrat-
ed in Figure 1. Replace the power cord if the grounding
pin is damaged or broken.
Extension cords connected to this machine should be 12
gauge, three-wire cords with three-prong plugs and out-
lets. DO NOT use extension cords more than 25 feet
(7.6 m) long
.
Figure 1

5
CORD SAFETY
• Do not leave appliance when plugged in. Unplug
from outlet when not in use and before servicing
• Do not use with damaged cord or plug. If appliance is
not working as it should, has been dropped, damaged,
le outdoors, or dropped into water, return to service
center for inspection and repair.
• Do not pull or carry by cord, use cord as handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run this SATURN over the
cord. Keep cord away from heated surfaces.
• Do not unplug by pulling cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Always unplug the machine when removing brush.
• is equipment should be stored indoors and not
exposed to rain.
CORD STORAGE:
While not in use, storage can be accomplished by wind-
ing cord around handle assy. Cord should be
completely unwound during operation.
MAINTENANCE:
is SATURN has been engineered and built to require
minimum maintenance. But like any machine, it does
require some care to keep it in optimum working condi-
tion. Careful attention to these maintenance instructions
will give you maximum operating performance and life
expectancy of the machine.
CAUTION: Disconnect the power cord from the outlet
before doing any clean up or maintenance on the ma-
chine
1. Keep the machine clean. Do not allow dust to accu-
mulate on external surfaces, the motor, or near any
moving parts.
2. Aer every job, wipe down the surface of the ma-
chine with a clean damp cloth.
3. Inspect cord for damage. Do not use machine with a
damaged cord.
CLEAN UP & STORAGE
1. Unplug and wrap it under the cord hook and around
the le side handle grip. Clean the cord and inspect it
for cuts, gashes and loose prongs.
2. Wipe down the machine and store in clean dry place.
3. To prevent deformation of pad and pad driver, re-
move them before storing.
4.
WARNING: Do not store the machine with the drive
block, pad driver or brush on the machine.
PAD INSTALLATION:
1. To install pad, tilt the machine back on the rear
wheels until machine is resting on handle.
2. Center the pad on the pad holder and insert pad cen-
ter lock. Twist clockwise to lock. Make sure the center
lock is tight.
To remove: Twist the center lock counterclockwise
3. Use the appropriate pads for the oor condition and
surface. Lighter pads are less abrasive and darker pads
are more abrasive. e correct pad will give you the
best results. Consult your local distributor for recom-
mendations.
4. Do not use pads that are larger than 20” in diameter.
Center
lock

6
TO ADJUST A DRIVE BELT
1. Locate the motor pulley on the underside of
the machine. It will be the only pulley visi-
ble. ere will be 4 motor mounting bolts sur-
rounding it. ese bolts fasten the motor to the
frame and can move along the slotted open-
ing. Loosen, but do not remove, the 4 bolts.
2. Locate the two belt tensioner s at the rear of the ma-
chine
3.
4. On the belt tensioners, locate the two jam nuts. ere
is a front and a rear.
5.
FRONT
REAR
6. To reduce belt tension, loosen the front jam nut and
tighten the rear.
7. To increase tension, loosen the rear jam nut and
tighten the front.
8. Always adjust both tensioners exactly the same way.
9. Once the belt has reached appropriate tension, tight-
en the jam nuts.
10. Tighten the 4 motor mounting bolts, test and adjust
until the belt does not slip.
WARNING: DO NOT OVER-TIGHTEN THE BELT.
ALWAYS TIGHTEN OR LOOSEN IN SMALL INCRE-
MENTS.
SERVICING:
In the event that your SATURN requires service, please
contact EDIC:
800-338-3342
No user serviceable components are employed in this
equipment. Do not attempt repairs yourself. EDIC will
assist you in locating an indepedent service contractor.

7
MACHINE ON/OFF OPERATION:
is equipment is equipped with a safety “LOCK OUT”
lever. Refer to Diagram 1 for steps 5, 6, and 7.
1. Install the pad driver and pad or attachment.
2. Plug in machine.
3. Lean the machine back, with all four wheels on the
oor, so the pad is not making contact with the oor
when you turn the motor on.
4. Place both hands on the handle grips with your n-
gers around the ON/OFF lever (Refer to B on Dia-
gram 1) Which extends from one side to the other,
underneath the handle grips.
5. e safety “LOCK OUT” lever (Refer to A on Dia-
gram 1) is located underneath the right side handle
grip and switch lever. To unlock the “LOCK OUT”
lever, use your right hand fore nger to press the lever
toward the back of the switch box.
6. With “LOCK OUT” lever in the unlocked position,
pull up on either side of the ON/OFF lever (Refer to
B on Diagram 1) to power the motor. Pull up on only
one side of the ON/OFF lever.
7. Wait 5 seconds for the motor to reach full speed and
place pad on the oor.
TO MANEUVER THE MACHINE:
CAUTION:
THIS MACHINE CANNOT BE OPERATED WITH
THE HANDLE IN THE UPRIGHT POSITION.
DOING SO WILL CAUSE LOSS OF CONTROL AND
POSSIBLE INJURY.
1. Lower the handle to a comfortable height for the op-
erator. is machine should operate with the handle
unlocked at about waist level. Do not lock the handle
into a xed position.
2. It is best that the operator begin operation closest to
the power outlet and move outward as far as the pow-
er cord will permit, then, work back to the original
point.
3. Move the machine in forward and reverse. Do not
swing side to side.
4. To stop the machine, simply release ON/OFF levers.
5. Do not use on wet oors.
B
B
A
Diagram 1

8

9

10

11

12

13

14

15

16
74
81
5
58
75
26
22
83
72
28
15
85
67
39
49
41
20
89
17
44
45
68
71
23
1
18
77
78
56
95
70
50
43
82
57
32
17
45
79
16
44 93
20
20HS1500-BK-SV &
20HS2000-BK-SV
FLOOR MACHINE BASE
ASSEMBLY
EXPLODED
VIEW
77
46
38
37
69
42
80
40
34
62
35
21
33
76
53
29
52
53 51
94
1/17/2019 REV 04

17
9 10
86
61
87
88
90
8
12
13
3
4
31
63 64
55
61 1
25
54 66
24
59
7
30
91
2
19
36 60
65
92 27
14
40
32
1/17/2019 REV 04
20HS1500-BK-SV &
20HS2000-BK-SV
FLOOR MACHINE
HANDLE ASSEMBLY
EXPLODED VIEW
84
47
48

18
HS1500-BK-SV
HS FLOOR MACHINE
PARTS LIST
1/17/2019 REV 04
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 2400BR PAD HOLDER, HIGH SPEED, 20" 1
2
B00177 TERMINAL LUG, QD F 16-14AWG, F.INS 2
3
B00180-10-3 RING TERMINAL, 16-14AWG, P.INS 1
4
B00187 CABLE CLAMP, NYLON .43 1
5
B02196-1 INDICATOR LIGHT 1
6
B10734 STRAIN RELIEF, HANDLE 1
7
B11465 SWITCH, DPST PUSH BUTTON 1
8
B11465-NUT NUT, SWITCH 1
9
B11504 STRAIN RELIEF 1
10
B11505 LOCKNUT, STRAIN RELIEF 1
11
B11513 POWERCORD, 14GA 1
12
B11518 INSULATION PAPER 1
13
B11762 TERMINAL LUG, QD F, 12-10AWG, F.INS 2
14
B11900 POWERCORD, 12GA 1
15
C00233 WASHER, FLAT, USS 1/4 2
16
C00240 SHOULDER WASHER, NYLON 6
17
C00250 LOCK WASHER, 3/8 SPLIT 3
18
C00251 LOCK WASHER, 5/16, SPLIT 4
19
C00252 WASHER, 3/8 x 13/16 1
20
C00252-1 WASHER, 3/8 6
21
C00259 WASHER, SLOTTED 1
22
C00261 HEX NUT, 1/4-20 6
23
C00262 HEX NUT, 5/16 4
24
C00278 LOCKNUT, 10-32, NYLON, SS 1
25
C00284 SCREW, 10-32 x 3/8, GND 1
26
C00297 SCREW, #8 x 1/4 SMS, SS 2
27
C00306 ROLL PIN 2
28
C00319-1 HEX SCREW, 1/4-20 X 3 1/2", SS 2
29
C02305 PUSH NUT 2
30
C11491 SCREW, 10-32 X 1" SS 1
31
C11502 SCREW, 3/8-16, SHCS 1
32
C11529 SCREW, 10-32 x .375, PH BLK OX 9
33
C11536-1 SPADE BOLT 1
34
C11537 DOWEL PIN 1
35
C11538 PUSH NUT 1
36
C11541 LOCKWASHER, 3/8, EXT. STAR 1
37
C11555 KEY, 316 2
38
C11556 WAVE WASHER 2
39
C11558 LOCKNUT, 3/8-16 2

19
HS1500-BK-SV
HS FLOOR MACHINE
PARTS LIST
1/17/2019 REV 04
ITEM NO. PART NUMBER DESCRIPTION QTY.
40 C11558 LOCKNUT, 3/8-16 2
41
C11559-1 WASHER, 1/2 4
42
C11567 SET SCREW 3
43
C11568-1 HEX BOLT, 5/16 X 2.5, SS 4
44
C11569-1 SCREW, 3/8 X 1.25, HH, SS 4
45
C11571-1 SCREW, 3/8 X 3/4, HH, SS 3
46
C11574 RETAINING RING 2
47
C13100 NUT, M14 1
48
C13101 SCREW, M14 1
49
C14150 WASHER, 3/8 NYLON 2
50
C14724 SCREW, 1/2-13 x 3, HEX, ZINC PLATED 2
51
C14725 LOCKNUT, 1/2-13, ZINC PLATED 2
52
C14726 SCREW, 3/8-24 x 1 1/2 L, HEX 2
53
C14727 HEX NUT, 3/8-24, ZINC PLATED 4
54
C90007-1 SHOULDER SCREW, 10-32 1
55
D11479 HANDLE 1
56
D11486 PAD COVER, 20 1
57
D11490B-1 DRIP COVER 1
58
D11490B-1-H DRIP COVER W/ LIGHT 1
59
D11494 SAFETY LOCK BRACKET 1
60
D11495 TRIGGER 1
61
D11496 COVER, SWITCH BOX 1
62
D11497 HANDLE, LOCKING CLAMP 1
63
D11507 CORD HOOK, CLAMP 1
64
D11507-2 CORD HOOK, BODY 1
65
D11523-1 TRIGGER SPRING, 3/8" OD 2
66
D11524 SPRING, LOCKOUT 1
67
D11526-1 BASE 1
68
D11532 PULLEY, 2" W/ GROOVES 1
69
D11547 PULLEY, 1500 RPM
1
70
D11534 SHAFT 1
71
D11535 WASHER, 1.75 OD, STEEL 1
72
D11542 BRACKET, TENSION ADJUSTMENT 2
73
D11543 HANDLE BRACE, L BK HS 1
74
D11544 HANDLE BRACE, R BK HS 1
75
D11545 MOTOR SCREEN, HIGH SPEED 1
76
D11562 AXLE, WHEEL, HISPEED 1
77
D11565 HOUSING, BEARING 2
78
E11478 BUMPER 1
79
F11988 PAD, HIGH SPEED, 20" 1

20
HS1500-BK-SV
HS FLOOR MACHINE
PARTS LIST
1/17/2019 REV 04
ITEM NO. PART NUMBER DESCRIPTION QTY.
80 G11531 BEARING 2
81
G11557 MOTOR, HIGH SPEED 1
82
G11943 WHEEL, 5" 4
83
H00565-5 LABEL, SERIAL #, STANDARD 1
84
H02548-2 LABEL, CORD 1
85
H03545 COVER, SERIAL # LABEL 1
86
H11493 SAFETY LABEL 1
87
H11831 EDIC LABEL 1
88
H12070 LABEL, 1500RPM
1
89
K00662-500 SPACER 2
90
K11498 GRIP, HANDLE 2
91
K11519 CAP, LOCKOUT BRACKET 1
92
K11520 GRIP, LEVER 2
93
K14145 SPACER, 1.48L 2
94
K14709 PLUG, RATCHET, .281D x .891L 2
95
L11530 BELT 1