Savoy House Circulaire User manual

OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Circulaire
CEILING FAN

1. TOOLS AND MATERIALS REQUIRED
● Philips screw driver
● Blade screw driver
● Step Ladder
● Wire Cutters
● Carpenter’s Level
2. PACKAGE CONTENTS
The following items should be contain within the
package;
Hanger Bracket Assembly
Downrod
Fan Head Assembly
Light Kit
Package Hardware:
Screws
Washers
Spring Washers
Tooth Washers
Wire Nuts
1

3. SAFETY RULES
1. To reduce the risk of electrical shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualied licensed electrician.
3. WARNING: To reduce the risk of electrical
shock and re, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes
commonly used for the support of lighting
xtures are not acceptable for fan support and
may need to be replaced, consult a qualied
electrician if in doubt.
_______________________________________
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRICAL SHOCK OR PERSONAL INJURY,
MOUNT FAN TO OUTLET BOX MARKET
“ACCEPTABLE FOR FAN SUPPORT”.
_______________________________________
5. The outlet box and support structure must
be securely mounted and capable of reliably
supporting a minimum of 50 pounds. Use only
CUL Listed outlet boxes marked “FOR FAN
SUPPORT”.
6. The fan must be mounted with a minimum of 6
feet clearance.
7. Do not adjust fan heads while fan blades are
in motion. Fan must be turned off and blades
stopped before adjusting fan heads or reversing
direction.
8. Avoid placing objects in the path of the fan
heads.
9. To avoid personal injury or damage to the fan
and other items, be cautious when working
around or cleaning the fan.
10. Do not use water or detergents when cleaning
the fan or fan blades. A dry dust cloth or
lightly dampened cloth will be suitable for most
cleaning.
11. After making electrical connections, spliced
conductors should be turned upward and
pushed carefully up into the outlet box. The
wires should be spread apart with the grounded
conductor and the equipment-grounding
conductor on one side of the outlet box.
12. Electrical diagrams are reference only. Light
kit that are not packed with the fan must be
CUL Listed and marked suitable for use with
the model fan being installed. Switches must
be CUL General Use Switches. Refer to the
Instructions packaged with the light kits and
switches for proper assembly.
_______________________________________
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT INSERT OBJECTS IN THE
PATH OF THE BLADES.
_______________________________________
NOTE: The important safety precautions and
instructions appearing in the manual are not meant to
cover all possible conditions and situations that may
occur. It must be understood that common sense and
caution are necessary factors in the installation and
operation of this fan.
2

4. MOUNTING OPTIONS
If there isn’t an existing CUL listed mounting box,
then read the following instructions. Disconnect
the power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
(at least 50 lbs.). Do not use plastic outlet boxes.
Figures 4.1, 4.2 and 4.3 are examples of different
ways to mount the outlet box.
NOTE: A longer downrod maybe need to maintain
proper clearance when installing on a steep,
sloped ceiling. (Fig. 4.3)
To hang a fan where there is an existing xture, but
no ceiling joist, an installation hanger bar should
be used as shown in Figure 4.4.
Figure 4.1
Figure 4.2
Figure 4.3
Figure 4.4
Outlet box
Outlet box
Provide strong
support
Ceiling
mounting
plate
Recessed
outlet box
Outlet box
3

5. HANGING THE FAN
Remember to turn off the power. Follow the steps
below to properly hang the fan.
Step 1. Pass the 120-volt supply wires through
the center hole in the Hanger Bracket and secure
the Hanger Bracket to the CUL Listed Electrical
Box with the screw and washers provided. Tighten
the mounting screws securely. (Fig. 5.1)
Step 2. Connect the Receiving Unit to the black
and white 120-volt supply wires. (Fig. 5.2)
Step 3. Prepare the fan to be hung. Locate the
Ball/Downrod. Remove the Lock pin (1) and
Washer, then slide the Hanger pin (2) out. (Fig. 5.3)
CUL Listed Electrical Box
Hanger Bracket
Washer
Tooth Washer
Spring Washer
Screw
Figure 5.1
White Wires
Black Wires
Receiving Unit
Figure 5.2
Ball/Downrod
Washer
Lock Pin
Hanger Pin
Figure 5.3
4

Step 4. Route wires exiting the top of the Collar
through the Decorative Housing, the Canopy and
the Ball/Downrod. Align the holes at the bottom of
the Downrod with the holes in the Collar. Carefully
insert the Hanger Pin through the holes in the
Collar and the Downrod. Be careful not to jam
the pin against the wiring inside the Downrod.
Slide the Washer over the end of the Hanger Pin.
Next, insert the Lock Pin through the hole near
the end of the Hanger Pin until it snaps into its
locked position. Tighten the set screw and slide
the Decorative Housing into place. (Fig. 5.4)
Step 5. Place the Downrod Ball into the
Hanger Bracket socket. Align the Downrod Ball
Registration Slot with the ridge inside the Bracket
socket to secure the ball. (Fig. 5.5)
Step 6. An additional safety support is provided
to prevent the fan from falling. Secure the Safety
Cable to the ceiling joist with screw and washers.
(Fig. 5.6)
Figure 5.5
Registration Slot
Figure 5.6
Safety Cable
Washer
Screw
Spring Washer
5
Figure 5.4
Canopy
Decorative
Housing
Lock Pin
Hanger Pin
Washer
Set Screw
Collar
Ball/Downrod
Horizontal
Support Bar

Step 7. Securely connect each of the Receiver Unit
wires to its corresponding color wire exposed from
the top of the Downrod Ball with a connecting wire
nut. Also, connect all Ground wires (green) with the
main Ground wire from the Electrical Box. (Fig. 5.7)
Step 8. Carefully turn the connecting nuts upward
and push the wiring into the electrical outlet box.
There should be space to allow the Receiver Unit to
slide in above the Downrod Ball. (Fig. 5.8)
Step 9. Loosen the left Canopy Screw and
remove the right Canopy Screw on the bottom of
the Hanger Bracket. (Fig. 5.9)
Step 10. Slide the Canopy over the Hanger
Bracket and align the larger screw hole over the
left Canopy Screw. Give the Canopy a slight twist
to the left, which should align the right Canopy
Screw hole. Insert and secure the right Canopy
Screw, then secure the left Canopy Screw. (Fig. 5.10)
Use a level to test that the Horizontal Support
Bar is hanging parallel to the oor. Rotate the
fan slowly one full revolution. If the fan is not
hanging parallel, the level will conrm it. Recheck
the Electrical Box, Hanger Bracket and/or Ball/
Downrod. Caution: Do not operate fan if the level
shows the Horizontal Support Bar is not hanging
parallel to the oor.
Figure 5.7
Ground Wires
Corresponding
Color Wires
from Receiver
Unit and
Downrod Ball
Receiver Unit
Figure 5.8
Canopy
Screw (left) Canopy
Screw (right)
Hanger
Bracket
Figure 5.9
Hanger
Bracket
Canopy
Canopy
Screw (right)
Figure 5.10
6

6. INSTALLING THE LIGHT KIT
Remember to turn off the power. Follow the steps
below to properly install the light.
Step 1. Remove the three Screws that hold the
Decorative Center Hub in place.
Step 2. Plug the Upper Housing Electrical
Connectors into the Light Housing Electrical
Connectors.
Step 3. Slide the Light Housing into the Upper
Housing and align the screw holes. Reinstall the
three Screws in the Upper Housing to secure the
Light Housing. Next, Install the Bulb in the Socket,
using a clockwise rotation.
NOTE: DO NOT TOUCH the halogen bulb with
bare ngers!. Oils on your skin will shorten the life
of the bulb. Use a tissue to remove the bulb from
the packaging and when installing the bulb into the
light xture.
Screw
Decorative
Center Hub
Figure 6.1
Figure 6.2
Upper
Housing
Upper Housing
Electrical
Connectors
Light
Housing
Light Housing
Electrical
Connectors
Light
Housing
Upper
Housing
Bulb
Screws
Socket
Figure 6.3
7

Figure 6.4
Light
Cover
Light
Housing
Pin
Channel
Step 4. Align the channels on the Light Cover to
align with the Pins inside the Light Housing and
slide the cover in. Carefully twist the Light Cover
clockwise to secure it in place. The Light Cover
should t snug against the Light Housing. (Fig. 6.4)

7. ADJUSTING SPREAD AND ROTATION SPEED
Remember to turn off the power when adjusting
the Spread and Rotation Speed.
Fan Heads adjust individually.
SPREAD
Adjusting the Fan Head angle up expands
the spread of the air movement in the space.
Adjusting the Fan Head angle down contains the
air movement.
To adjust the angle, grasp the Fan Head and slightly
loosen the Tilt Adjustment Knob. Tilt the Fan Head
to the desired position. Hold the position while re-
tightening the Tilt Adjustment Knob. (Fig.7.1)
ROTATION SPEED
To reduce the risk of injury to persons or possible
damage to fan, DO NOT over adjust the fan to spin
at an unreasonable rate.
Only one Fan Head need be adjusted to create
rotation.
The greater the angle (left or right) of the Fan
Head to the horizontal support rod, the faster the
speed of rotation. The less the angle of the Fan
Head, the slower the speed of rotation.
To adjust the rotation speed, loosen the Friction
Knob and turn the Fan Head to the desired angle,
left or right. Re-tighten the Friction Knob. (Fig. 7.2)
In addition, the rotation of the fan can be sped up
or slowed down by increasing or decreasing the
motor speed of the fan.
8
Tilt Adjustment
Knob
Friction
Knob
Left / Right
Horizontal
Support Rod
Horizontal
Support Bar
Down
Tilt Adjustment
Knob
Up
Figure 7.1
Figure 7.2

CLEANING
• Remember to turn off the power when
cleaning the fan.
• Clean the Motor Housings, Decorative
Housing and Horizontal Support Bar using
a clean, soft cloth, slightly dampened, if
necessary.
• DO NOT allow water to drip on or into the fan
motor housings.
• NEVER use abrasive cleaning agents
or solvents. This may cause damage or
deterioration to the surface of the unit.
To Clean the Grills and Blades
• Remove the small Safety Screws and Nuts at
the bottom of the grills.
• Unlock the metal clips around the fan grills
and remove the front grills by lifting slightly to
detach the top alignment tab from the back
grills.
• The fan blades and grills may be cleaned with
a soft cloth, slightly dampened, if necessary.
A small, soft, clean brush, (a small paintbrush
will do), may also be used to remove dust in
hard-to-reach places.
• NEVER use abrasive cleaning agents or
solvents on the blades or grills. This may
cause damage or deterioration to the
surfaces.
• Reattach the front grills to the fans after all
parts have dried completely. To do so, secure
the top alignment tabs to the back grills. Align
the front grills against the rear grills and snap
the grill clips closed.
• Reinsert the small Safety Screws at the
bottom of the grills and secure in place with
Nuts.
• DO NOT turn the fan on until it is fully
reassembled.

Exclusively Distributed by
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS