Savoy House M2009 Series User manual

FAN RATING AC 120V. 60Hz
UL LISTED MODEL : AC-552
READ AND SAVE THESE INSTRUCTIONS
CEILING FAN OWNER'S MANUAL
MODELS: M2009XX

2. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a. Set of blades assembly (5)
b. Hanger bracket
c. Canopy
d. Downrod
e. Fan motor assembly
f. Set of blades bracket (5)
g. Mounting plate
h. Switch housing
i. Light kit assembly
j. Glass shade
k. 7W LED bulb
l. Pull chains and fobs (2)
m. Package hardware
1) Mounting hardware :
screws(2), lock washers(2),
star washers(2), wire nuts(3)
wood screws(2), washers(2)
2) Blade attachment hardware:
screws (16), fiber washers (16)
3) Blade bracket hardware:
screws with lock washers (11)
4) Balance Kit
1
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
1. TOOLS AND MATERIALS
REQUIRED
a
j
m
k
b
c
d
e
f
g
h
l
i

2
3. SAFETY RULES
1. To reduce the risk of electric shock, insure
electricity has been turned off at the
circuit breaker or fuse box before
beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed
electrician.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To reduce the risk of fire, electric
shock, or personal injury, mount to outlet
box marked "acceptable for fan support of
15.8 kg (35 lbs.) or less" and use mounting
screws provided with the outlet box. Most
outlet boxes commonly used for the
support of light fixtures are not acceptable
for fan support and may need to be
replaced. Due to the complexity of the
installation of this fan, a qualified licensed
electrician is strongly recommended.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use only UL Listed outlet boxes
marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge
of the blades to the floor.
7. Do not operate reversing switch while fan
blades are in motion. Fan must be turned
off and blades stopped before reversing
blade direction.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After marking electrical connections,
spliced conductors should be turned
upward and pushed carefully up into
outlet box. The wires should be spread
apart with the grounded conductor and
the equipment-grounding conductor on
one side of the outlet box.
12. Electrical diagrams are reference only.
Light kit that are not packed with the fan
must be UL Listed and marked suitable for
use with the model fan you are installing.
Switches must be UL General Use
Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
TO OUTLET BOX MARKED "ACCEPTABLE
FOR FAN SUPPORT".
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE BRACKETS (ALSO
REFERRED TO AS FLANGES) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT
INSERT OBJECTS IN THE PATH OF THE BLADES.

4. MOUNTING OPTIONS
If there isn't an existing UL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1, 2 and 3 are examples of different
ways to mount the outlet box.
Note: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. (Fig. 3)
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4.
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Figure 1
Figure 3
Figure 4
Outlet box
Figure 2
3
ANGLED CEILING
MAXIMUM 25° ANGLE

REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Pass the 120-volt supply wires
through the center hole in the ceiling hanger
bracket as shown in Fig. 5.
Step 2. Secure the hanger bracket to the
ceiling outlet box with the screws and
washers provided with your outlet box. (Fig. 5)
Step 3. Remove the hanger pin, lock pin and
set screws from the top of the motor
assembly. (Fig. 6)
Step 4. Route the safety cable and wires
exiting from the top of the fan motor through
the decorative scroll assembly, canopy cover,
canopy and then through the ball / downrod.
(Fig. 6)
Step 5.Route wires exiting from the top of the
fan motor through the canopy and then
through the ball / downrod.
Step 6. Align the holes at the bottom of the
downrod with the holes in the collar on top of
the motor housing (Fig. 6). Carefully insert the
hanger pin through the holes in the collar and
downrod. Be careful not to jam the pin against
the wiring inside the downrod. Insert the
locking pin through the hole near the end of
the hanger pin until it snaps into its locked
position, as noted in the circle inset of Fig. 6.
Step 7. Tighten two set screws on top of the
fan motor firmly. (Fig. 6)
Step 8. Place the downrod ball into the
hanger bracket socket. (Fig. 7 )
5. HANGING THE FAN
4
Figure 5
Figure 6
Figure 7
Registration slot
Downrod
Canopy
Set screws
Hitch pin
Lock pin
120V Wires
CUL Listed
electrical box
Hanger
bracket
Hook
Mounting screws
(supplied with
electrical box)
Safety cable

5
6. MAKE THE ELECTRIC
CONNECTIONS
Remember to disconnect the power.
Follow the steps below to connect the fan to
your household wiring. Use the wire
connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or
connections.
Step 1. Connect the fan supply (black) wire
and light supply (blue) wire to the black
household supply wire as shown in Figure 8.
Step 2. Connect the neutral fan (white) wire to
the white neutral household wire.
Step 3. Connect the fan ground wire (green)
to the household ground wire.
Step 4. After connecting the wires, spread
them apart so that the green and white wires
are on one side of the outlet box and the black
and the blue wires are on the other side.
Step 5. Turn the connecting nuts upward and
push the wiring into the outlet box.
Figures 9 and 10 illustrate the wiring
connections for optional wall control. (The
wire color out of wall control may vary, see
wall control's installation manual for correct
wire connections.)
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR OTHER PERSONAL
INJURY. MOUNT FAN ONLY ON AN OUTLET
BOX OR SUPPORTING SYSTEM MARKED
ACCEPTABLE FOR FAN SUPPORT.
Figure 8
Figure 9
BLK
WH
BLUE
BLK
WH
GRN
WIRING
BOX
WIRING
BOX
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
BLUE
BLK WH
WH
FAN
LIGHT
POWER LINES 120V
POWER LINES 120V
BLK
WH
BLUE
BLK
WH
FAN
LIGHT
BLK
BLUE WH
WH
LIGHT
SWITCH
GREEN GROUND
GREEN GROUND
Figure 10
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
POWER LINES 120V
GREEN
GROUND
WIRING
BOX
BLK
WH
BLUE
BLK
WH
FAN
LIGHT
WH
WH
BLUE
BLK
LIGHT FAN

6
7. FINISHING THE
INSTALLATION
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Secure the canopy to the hanger
bracket with the four canopy mounting screw
provided. (Fig. 11)
WARNING: Make sure tab at bottom of
hanger bracket is properly seated in groove
of hanger ball before attaching canopy to
bracket. Failure to properly seat tab in groove
could cause damage to electrical wiring.
Figure 11
Figure 12
Outlet box
Hanger
bracket
Canopy
Screws
8. ATTACHING THE
FAN BLADES
CAUTION: Remove 5 rubber packing mounts
and discard before installation.
Step 1. Attach the blade to the blade bracket
using the screws and fiber washers as shown
in Figure 12. Start screw into bracket. Repeat
for the two remaining screws.
Step 2. Tighten each screw. Make sure the
blade is straight.
Step 3. Fasten blade assembly to motor using
the screws supplied. (Fig. 12)
Fiber
washers
Blade
Blade bracket
Screws

7
9. INSTALLATING
THE MOUNTING PLATE
1. Remove the 1 of 3 screws from the
mounting ring and loosen the other 2
screws. (Do not remove)
2. Place the key holes on the mounting plate
over the 2 screws previously loosened
from the mounting ring, turn mounting
plate until it locks in place at the narrow
section of the key holes. Secure by
tightening the 2 screws previously
loosened and the one previously
removed. (Fig. 13)
Figure 13
Figure 14
Mounting
plate
Mounting ring
Screws
10. INSTALLATING THE
LIGHT KIT TO THE
SWITCH HOUSING
1. Remove and discard the center plug from
the switch housing.
2. Attach the light kit to the switch housing
by feeding the light kit wires (black and
white) through the hole of switch housing
and then screw it onto the switch housing by
nut & lock washer. Be sure it is tight enough
to prevent light kit from vibrating loose.
3. Make sure the white wire from the light kit
connected to the white wire from switch
housing, and black wire from light kit
connected to the blue wire from switch
housing. (Fig. 14)
Switch housing
Plug Lock washer
Light kit
Wire nuts
Nut

8
Figure 16
12. INSTALLING THE LED
LIGHT BULBS AND
GLASS SHADE
1. Install 1x 7W LED bulb (included).
2. Install the glass shade to the light kit
assembly with 3 screws provided. (Fig. 16)
3. Restore power and your light kit is ready
for operation.
Figure 15
11. INSTALLING
THE LIGHT KIT
ASSEMBLY
NOTE: Before starting installation, disconnect
the power by turning off the circuit breaker or
removing the fuse at fuse box.
Step 1. Remove the 3 screws from the
mounting plate.
Step 2. While holding the Light kit assembly
under your fan, snap together the wire
connection plug. (Fig. 15)
Step 3. Install the Light kit assembly onto the
mountimg plate with 3 screws provided. Be
sure to tighten all screws. (Fig. 15)
Mounting plate
Wire connectors
Light kit
assembly
Light kit
assembly
Srews
Bulb
Screws
Glass shade

9
Figure 17
Figure 18
13. OPERATING YOUR FAN
Turn on the power and check the operation of
your fan. The pull chain controls the fan speed
as follows: 1 pull- High, 2 pulls-Medium, 3
pulls- Low, and 4 pulls-Off.
Light pull chain it controls the light in "ON" or
"OFF".
Speed settings for warm or cool weather
depend on factors such as the room size,
ceiling height, number of fans and so on.
The slide switch controls directions: forward
(switch down) or reverse (switch up).
NOTE: Wait for fan to stop before changing
the setting of the slide switch.
Warm weather - (Forward) A downward
airflow creates a cooling effect as shown in
Fig. 17. This allows you to set your air
conditioner on a warmer setting without
affecting your comfort.
Cool weather - (Reverse) An upward airflow
moves warm air off the ceiling area as shown
in Fig. 18. This allows you to set your heating
unit on a cooler setting without affecting your
comfort.