Savoy House M2012 Series User manual

FAN RATING AC 120V. 60Hz
UL LISTED MODEL : AC-552DL
MODEL: M2012XX
READ AND SAVE THESE INSTRUCTIONS
OWNER'S MANUAL
52” CEILING FAN

2. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a. Set of blades assembly (3)
b. Blade support plates (3)
c. Hanger bracket assembly
d. Downrod
e. Coupling cover
f. Fan motor assembly
g. Mounting plate
h. Light kit
i. Glass shade
j. Receiver+6 wire nuts
k. Transmitter+holder+2 mounting
screws+3voltbattery(CR2032)
l. Package hardware
1)Mountinghardware:
screws(2),lockwashers(2),
starwashers(2),wirenuts(3),
wood screws (2)
2)Bladeattachmenthardware:
screws with lock washers (7)
3)BalanceKit
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
1
1. TOOLS AND MATERIALS
REQUIRED
a
cj
k
e
f
g
h
i
d
b
l

2
3. SAFETY RULES
1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performedbyaqualifiedlicensedelectrician.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To reduce the risk of fire, electric
shock, or personal injury, mount to outlet box
marked "acceptable for fan support of 15.8 kg
(35 lbs.) or less" and use mounting screws
provided with the outlet box. Most outlet
boxes commonly used for the support of light
fixtures are not acceptable for fan support
and may need to be replaced. Due to the
complexity of the installation of this fan,
a qualified licensed electrician is strongly
recommended.
5. The outlet box and support structure must
be securely mounted and capable of reliably
supporting a minimum of 50 pounds. Use
only UL Listed outlet boxes marked "FOR
FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
thebladestothefloor.
7. Wait for fan to stop before changing the
setting of the slide switch.
8. Avoid placing objects in the path of the
blades.
9. Toavoidpersonalinjuryordamagetothefan
and other items, be cautious when working
aroundorcleaningthefan.
10. Donot usewaterordetergentswhencleaning
thefan or fanblades. A drydust cloth orlightly
dampened cloth will be suitable for most
cleaning.
11. After marking electrical connections, spliced
conductors should be turned upward and
pushed carefully up into outlet box. The wires
should be spread apart with the grounded
conductor and the equipment-grounding
conductor on one side of the outlet box.
12. Electrical diagrams are reference only. Light
kit that are not packed with the fan must be
UL Listed and marked suitable for use with
the model fan you are installing. Switches
must be UL General Use Switches. Refer to
the Instructions packaged with the light kits
and switches for proper assembly.
13. WARNING: Chemical Burn Hazard. Keep
batteries away from children.
14. Thisproduct containsalithium button/ coin
cell battery. If a new or used lithium button /
coin cell battery is swallowed or enters the
body, it can cause severe internal burns and
can lead to death in as little as 2 hours. Always
completely secure the battery compartment.
If the battery compartment does not close
securely, stop using the product, remove the
batteries, and keep it away from children.
IF you think batteries might have been
swallowed or placed inside any part of the
body, seek immediate medical attention.
15. The batteries shall be disposed of properly,
including keeping them away from children;
Even used cells may cause injury.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
TO OUTLET BOX MARKED "ACCEPTABLE
FOR FAN SUPPORT".
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS
IN THE PATH OF THE BLADES.

4. MOUNTING OPTIONS
If there isn't an existing UL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses
or turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 35 lbs). Do
not use plastic outlet boxes.
Figures 1,2 and 3 are examples of different
ways to mount the outlet box.
NOTE: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. (Fig. 3)
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4.
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Figure 1
Figure 3
Figure 4
Outlet box
Figure 2
3
Angled ceiling
maximum
18 angle

REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Remove the decorative canopy bottom
cover from the canopy by turning the cover
counter clockwise. (Fig. 5)
Step 2. Remove the hanger bracket from the
canopy by removing the 1 of 2 screws from the
bottomofthehangerbracketandlooseningthe
other one a half turn from the screw head. Next,
turn the canopy counter clockwise to removing
thehangerbracketfromthecanopy.(Fig.5)
Step 3. Pass the 120-volt supply wires through
the center hole in the ceiling hanger bracket as
shown in Fig. 6.
Step 4. Secure thehangerbracket to theceiling
outlet box with the screws and washers
provided with your outlet box.
Step 5. Removethehangerpin,lockpinandset
screws from the top of the motor assembly.
Step 6. Route wires exiting from the top of
the fan motor through the collar cover, canopy
cover, canopy and then through the ball /
downrod. (Fig. 7)
Step 7. Align the holes at the bottom of the
downrod with the holes in the collar on top
of the motor housing (Fig.7). Carefully insert
the hanger pin through the holes in the collar
and downrod. Be careful not to jam the pin
against the wiring inside the downrod. Insert
the locking pin through the hole near the end
of the hanger pin until it snaps into its locked
position, as noted in the circle inset of Fig. 7.
Step 8. Tighten two set screws on top of the
fan motor firmly. (Fig. 7)
Step 9. Place the downrod ball into the hanger
bracket socket. (Fig. 8)
5. HANGING THE FAN
4
Figure 6
Figure 5
Figure 7
Figure 8
Registration
slot
Hanger
bracket
Ceiling
canopy
Canopy
cover
120V Wires
Ceiling
hanger
bracket
Mounting screws
(supplied with
electrical box)
UL Listed
electrial box
Washers
Downrod
Canopy
Set screws
Hitch pin
Lock pin
Canopy cover
Coupling cover

5
6. MAKE THE ELECTRIC
CONNECTIONS
WARNING: To avoid possible electrical shock,
be sure electricity is turned off at the main
fuse box before wiring.
NOTE: This remote control unit is equipped
with 16 code combinations to prevent possible
interference from or to other remote units.
The frequency switches on your receiver and
transmitter have been preset at the factory.
Please recheck to make sure the switches on
transmitter and receiver are set to the same
position,any combinationof settingswill operate
the fan as long as the transmitter and receiver
are set to the same position. (Figure 9)
Step 1. (Figure 10) Insert the receiver into the
mountingbracketwith the flat sideofthe receiver
facing the ceiling.
Step 2. (Figure 11) Motor to Receiver Electrical
Connections: Connect the black wire from the
fan to black wire marked "TO MOTOR L". Connect
the white wire from the fan to the white wire
marked "TO MOTOR N" from the receiver.
Connect the blue wire from the fan to the blue
wiremarked "For Light"from the receiver.Secure
the wire connections with the plastic wire nuts
provided.
Step 3. (Figure 11) Receiver to House Supply
Wires Electrical Connections: Connect the black
(hot) wire from the ceiling to the black wire
marked "AC in L" from the receiver. Connect the
white (neutral) wire from the ceiling to the
white wire marked "AC in N" from the Receiver.
Secure the wire connections with the plastic
wire nuts provided.
Step 4. (Figure 11) If your outlet box has a
ground wire (green or bare copper) connect it to
the fan ground wires; otherwise connect the
hanging bracket ground wire to the mounting
bracket. Secure the wire connection with a
plastic nut provided. After connecting the wires,
spread them apart so that the green and white
wires are on one side of the outlet box and black
and blue wires are on the other side. Carefully
tuckthewireconnectionsupintotheoutletbox.
NOTE: Fan must be installed at a maximum
distance of 30 feet from the transmitting unit
for proper signal transmission between the
transmitting unit and the fan's receiving unit.
Figure 9
Figure 10
Receiver
Hanger
bracket
Code switch
ON
ON
ON ECE
1234
Figure 11
White (neutral)
White (neutral)
Green or bare
copper (ground)
White ("AC IN N")
White ("to motor N")
Ground
(green) (Connect to
ground wire on
hanger bracket
if no house
ground wire
exists.)
Outlet box
Black (hot)
Black ("AC IN L")
Black ("to motor L")
Receiver
Blue (for light)
Blue (for light)
Black (motor)

6
Figure 12
7. FINISHING THE
INSTALLATION
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Slide the canopy up to hanger bracket
and place the key hole on the canopy over the
screwonthehangerbracket,turncanopyuntilit
locks in place at the narrow section of the key
holes.
Step 3. Align the circular hole on canopy with
the remaining hole on the hanger bracket,
secure by tightening the two set screws.
NOTE: Adjust the canopy screws as necessary
until the canopy and canopy cover are snug.
(Fig. 12)
WARNING: Make sure tab at bottom of hanger
bracket is properly seated in groove of hanger
ball before attaching canopy to bracket. Failure
toproperlyseattabingroovecouldcausedamage
to electrical wiring.
8. ATTACHING THE FAN
BLADES
Step 1. Align the holes in the blade, the blade
support plate, and the fan motor assembly and
secure with a blade attachment screws with
lockwashers. (Fig.13)
Outlet box
Hanger
bracket
Canopy
Canopy cover
Screws
Figure 13
Blade
Screws with lock washers
Blade support plate

7
Figure 15
Mounting ring
Mounting
plate
Screws
Figure 14
9. INSTALLATING THE
MOUNTING PLATE
Step 1. Remove the 1 of 3 screws from the
mounting ring and loosen the other 2 screws.
(Do not remove)
Step 2. Place the key holes on the mounting
plate over the 2 screws previously loosened
from the mounting ring, turn mounting plate
until it locks in place at the narrow section of
thekey holes.Secure bytightening the2 screws
previously loosened and the one previously
removed. (Fig. 14)
10. INSTALLING THE LED
LIGHT KIT & LIGHT
SHADE
NOTE: Before starting installation, disconect
the power by turning off the circuit breaker
or removing the fuse at fuse box. Turning
power off using the fan switch is not sufficient
to prevent electric shock.
Step 1. Remove the 1 of 3 screws from the
posts of the mounting plate and keep it for
future use. Loosen the other 2 screws. (Do not
remove) (Fig. 15)
Step 2. While holding the LED light kit under
yourfan,makethepolarizedplugconnections:
- Red to white
- Black to black
Step 3. Place the key holes in the LED light kit
over the two screws previously loosened from
the mounting plate. Turn the LED light kit until
the LED light kit locks in place at the narrow
section of the key holes. (Fig. 15)
Step 4. Securely tighten the two light kit
mounting screws previously loosened and
the one previously removed. (Fig. 15)
Step 5. Raise glass shade up against the LED
light kit, and secure it to fan by turning glass
shadeclockwise untilsnug.DO NOT OVERTIGHTEN.
(Fig. 15)
LED Light kit
Screws
Mounting
Plate
Connection
plugs
Glass shade

12. OPERATING
INSTRUCTIONS
Restore power to ceiling fan and test for
properoperation.
A. , ,and buttons:
Thesethreebuttonsareusedtosetthefan
speedasfollows:
=highspeed
=mediumspeed
=lowspeed
B. button:
Thisbuttonturnsthefanoff.
C. button:
Thisbuttoncontrolsthelight.Press and
release the button to turn the light ON
or OFF. Press and hold the button to set
the desired brightness. The light key has
an auto-resume, it will stay at the same
brightness as the last time it was turned
off.
8
Figure 17
Figure 16
11. INSTALLING THE
BATTERY
Insert the 3 volt battery (included) and make
sure they are seated correctly in each recess
with the Positive + sign facing up. (Fig. 16)
ON ECE
1234

9
Here are some suggestions to help you maintain your fan
1. Because of the fan's natural movement, some connections may become loose. Check the
support connections, brackets, and blade attachments twice a year. Make sure they are
secure. (It is not necessary to remove fan from ceiling.)
2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft
brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to
minimize discoloration or tarnishing. Do not use water when cleaning. This could damage the
motor, or the wood, or possibly cause an electrical shock.
3. You can apply a light coat of furniture polish to the wood blades for additional protection and
enhanced beauty. Cover small scratches with a light application of shoe polish.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
13. CARE OF YOUR FAN
IMPORTANT
MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY
REPAIRS. REFER TO THE SECTION "MAKING ELECTRICAL CONNECTIONS".
Figure 18
Figure 19
TheReverseswitchislocatedonthemotor
housing.SlidetheswitchtotheLeftforwarm
weather operation. Slide the switch to the
Rightforcoolweatheroperation.
Speed settings for warm or cool weather
depend on factors such as the room size.
Ceilingheight,numberoffansandsoon.
NOTE: Wait for fan to stop before changing
thesettingoftheslideswitch.
Warmweather- (Forward) A downwardairflow
creates a cooling effect as shown in Fig. 18.
Thisallowsyoutosetyourairconditioneron
a
warmersettingwithout affectingyourcomfort.
Cool weather - (Reverse) An upward airflow
moveswarmairofftheceilingareaasshownin
Fig.19.Thisallowsyoutosetyourheatingunit
on a cooler setting without affecting your
comfort.

10
14. TROUBLESHOOTING
Problem
Fan will not start.
Fan sounds noisy.
Remote control
malfunction.
Fan wobble.
Solution
1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the
switch housing. CAUTION: Make sure main power is off.
3. Check to make sure the dip switches from the transmitter and receiver are
set to the same frequency.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub is
tight.
3. Make sure wire nut connections are not rubbing against each other or the
interior wall of the switch housing. CAUTION: Make sure main power is
off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new
fan disappear during this time.
5. If using an optional light kit, make sure the screws securing the glassware
are tight. Check that light bulb is also secure.
6. Do not connect the fan with wall mounted variable speed control (s).
7. Make sure the upper canopy is a short distance from the ceiling. It should
not touch the ceiling.
1. Do not connect the fan with wall mounted variable speed control (s).
2. Make sure the dip switches are set correctly.
1. Checkthat allbladeandbladearm screwsaresecure.
2. Most fan wobbling problems are caused when blade levels are unequal.
Check this level by selecting a point on the ceiling above the tip of one of
the blades. Measure this distance. Rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. The distance deviation
shouldbe equalwithin1/8".
3. Usethe enclosedBladeBalancingKitif thebladewobbleisstill noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by
side) blades can redistribute the weight and possibly result in smoother
operation.
WARNING: To reduce the risk of personal injury, do not bend the blade arm
while installing, balancing the blades, or cleaning the fan. Do not insert foreign
objects between rotating fan blades.