SBE 39Plus User manual

SEA-BIRD ELECTRONICS, INC.
13431 NE 20th Street, Bellevue, WA 98005 USA
Telephone: [phone] Fax: [phone] email: [e-mail]
Sea-Bird Electronics Procedure
PROCEDURE NUMBER: 67228
TITLE: SBE PN 60070 SBE 39Plus Spares Kit (Internal
Connector)
REVISION: A
EFFECTIVE DATE: 20 MAY 2014
SBE P/N 60070
SBE 39Plus Spares Kit (Internal Connector)
Kit Contents
SBE P/N Part Description Primary SBE Application QTY
31018 O-RING, PARKER 2-029 N674-70 End cap O-Rings 4
60039 SBE39 Desiccant Packs, 1gm- 25 ea Replace Desiccant bag every time you open the sensor 1 can
P
Pr ro oc ce ed du ur re e f fo or r S SB BE E 3 39 9P Pl lu us s
A. REPLACING THE BATTERY Follow the instructions below to replace the AA cells
1) Removethetitaniumendcapandelectronicsfromthehousingasfollows:
a) Wipetheoutsideoftheendcapandhousingdry,beingcarefultoremoveanywateratthe
seambetweenthem.
b) Usingawrenchontheendcap’swrenchflats,unscrewtheendcap.
c) Pulltheendcapandattachedelectronicsoutofthehousing.
d) RemoveanywaterfromtheendcapO‐ringsandmatingsurfacesinsidethehousingwitha
lint‐freeclothortissue.
2) ReplacetheAAcells:Pusheachcelloutofthebatteryholder,andinstallthenewcells.
3) (39pluswithexternalconnector)Installtwonewdesiccantcapsulesintheslotsontopofthe
batterypack.
4) (39pluswithnoexternalconnector)Installanewdesiccantbag
5) Reinstalltheendcap:
a) RemoveanywaterfromtheO‐ringsandmatingsurfacesinthehousingwithalint‐freecloth
ortissue.InspecttheO‐ringsandmatingsurfacesfordirt,nicks,andcuts.Cleanas
necessary.ApplyalightcoatofO‐ringlubricant(ParkerSuperOLube)toO‐ringandmating
surfaces.
b) Carefullyfittheendcapintothehousing,pushinginuntilthefirstO‐ringisseated.
c) Usingawrench,screwtheendcapintothehousing.
DATE RE
V
REVISION RECORD
A
UTH DR CHK
10/14
A
CHANGE O-RING FROM 31274 CB CB

SEA-BIRD ELECTRONICS, INC.
13431 NE 20th Street, Bellevue, WA 98005 USA
Telephone: [phone] Fax: [phone] email: [e-mail]
Sea-Bird Electronics Procedure
PROCEDURE NUMBER: 67228
TITLE: SBE PN 60070 SBE 39Plus Spares Kit (Internal
Connector)
REVISION: A
EFFECTIVE DATE: 20 MAY 2014
B. REPLACING THE O-RINGS
1. Remove the old O-Ring
a. Use a plastic spatula, or other NON-ABRASIVE, soft material to pry in underneath O-Ring.
b. Pull back so O-Ring stretches out of its groove, and cut it. Make sure not to scratch the O-
Ring seating surface.
c. Discard of old O-Ring immediately to insure they do not get accidentally reused.
2. Installing the new O-Ring
a. Make sure O-Ring is free of all dust and debris before applying any lubricant. Never clean
with any abrasive material.
b. Lubricate O-Ring with O-Ring lubricant. This should be a silicone-based lubricant. Never use
petroleum based lubricants on any SBE O-Rings.
c. Slip O-Ring over end cap and into the O-Ring groove..
d. Always close and seal the sensor as soon as possible after replacing an O-Ring.
e. Always clean and lubricate an O-Ring before installing it.
3. Install a new desiccant bag, and reseal the can.