SC2000 PZ0060 User manual

1
─4/8/16 CH DVR ─
User Manual
PZ0060 / PZ0061 /PZ00
62v0.01
This document contains preliminary information and subject to change without notice.
\

2
This symbol is intended to
alert the user to the presence
of unprotected “Dangerous
voltage" within the product's
enclosure that may be strong
enough to cause a risk of
electric shock.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
NOTE: This equipment has been tested
and found to comply with the limits for a
class digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference
in which case the user will be required to
correct the interference at his own expense.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.

3
Table of Contents
CHAPTER 1 PACKING DETAIL AND INSTALLATION_____________________ 5
1-1 PACKING__________________________________________________ 5
1-2 Hard Disk Installation_______________________________________ 5
1-3 DVD-RW Installation ________________________________________ 7
CHAPTER 2 PANEL LOCATION_______________________________________ 9
2-1 FRONT PANEL CONTROLS __________________________________ 9
2-2 16CH REAR PANEL CONNECTORS _____Error! Bookmark not defined.
2-3 8CH REAR PANEL CONNECTORS ____________________________11
2-4 4CH REAR PANEL CONNECTORS ___________________________ 12
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS_________________ 13
3-1 LIVE Mode _______________________________________________ 13
3-2 PLAYBACK Mode _________________________________________ 15
3-3 PTZ Mode________________________________________________ 17
CHAPTER 4 MAIN MENU SETUP___________________________________ 19
4-1 RECORD SETUP __________________________________________ 21
4-1.1 Quality & Frame Rate Setup ___________________________ 22
4-2 EVENT SETUP ____________________________________________ 23
4-2.1 MOTION SETUP ______________________________________ 23
4-2.1.1 MOTION AREA SETUP____________________________ 24
4-2.2 SENSOR SETUP______________________________________ 24
4-3 SCHEDULE SETUP ________________________________________ 26
4-3.1 Schedule Record Setup _______________________________ 26
4-3.2 Holiday Setup________________________________________ 26
4-4 CAMERA SETUP __________________________________________ 28
4-5 ACCOUNT SETUP _________________________________________ 29
4-5.1 Permission Setup_____________________________________ 29
4-5.2 User Picture Setup ___________________________________ 30
4-6 NETWORKING SETUP______________________________________ 31
4-6.1 NETWORKING SETUP_________________________________ 31
4-6.1.1 DHCP __________________________________________ 31
4-6.1.2 LAN____________________________________________ 31
4-6.1.3 ADSL _________________________________________ 32
4-6.2 HTTP Setup_________________________________________ 33
4-6.3 DDNS Setup ________________________________________ 33
4-6.4 Mail Setup__________________________________________ 34
4-7 PTZ & RS485 SETUP ______________________________________ 35
4-8 SYSTEM SETUP___________________________________________ 36
4-8.1 DISPLAY SETUP______________________________________ 37
4-8.2 DATE/TIME SETUP____________________________________ 38
4-8.2.1 CHANGE DATE & TIME___________________________ 38
4-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP ___ 39
4-8.2.3 INTERNET TIME SETUP __________________________ 39
4-8.3 BUZZER & RELAY SETUP _____________________________ 39
4-8.4 SPOT SETUP ________________________________________ 40
4-9 UTILITY SETUP ___________________________________________ 41
4-10 DIAGNOSTIC ____________________________________________ 42
CHAPTER 5 BACKUP & SEARCH___________________________________ 43
5-1 BACKUP SETUP __________________________________________ 43
5-2 SEARCH SETUP __________________________________________ 44
5-2.1 EVENT SEARCH______________________________________ 46

4
5-2.1.1 CRITERIA SETUP FOR EVENT SEARCH_____________ 46
5-2.2 TIME SEARCH _______________________________________ 48
5-3 AP Software Installation and Setup __________________________ 48
5-4 AP Software Operation_____________________________________ 50
CHAPTER 6 SPECIFICAITONS _____________________________________ 52
CHAPTER 7 MOBILE APPLICATION INSTALLATION AND USAGE _________ 55
7-1 Mobile Application Installation and Operation for Symbian System. 5
57-1.1 Mobile Application Installation__________________________ 55
7-1.2 Mobile Application Operation___________________________ 56
7-1.2.1 Add New Login DVR _____________________________ 56
7-1.2.2 Logging Onto the DVR ___________________________ 56
7-1.2.3 Modify the Login Information of DVR_______________ 57
7-1.2.4 Delete the Login Information of DVR _______________ 57
7-1.3 Live Monitoring Operation _____________________________ 58
7-1.3.1 Scroll the Image_________________________________ 58
7-1.3.2 Image Quality Setup _____________________________ 58
7-1.3.3 Channel Display _________________________________ 59
7-1.3.4 Size of Image ___________________________________ 59
7-1.3.5 Rotate the image ________________________________ 59
7-1.3.6 Alarm __________________________________________ 59
7-2 Mobile Application Installation and Operation for Windows Mobile S
ystem_______________________________________________________ 60
7-2.1 Mobile Application Installation__________________________ 60
7-2.2 Mobile Application Operation___________________________ 61
7-2.3 Operation under the LIVE monitoring. ___________________ 62
7-2.3.1 Operation uner the LIVE monitoring for Jrviewer ____ 62
7-2.3.2 Operation under the LIVE monitoring for H264 Pocket 63
CHAPTER 8 CMS INSTALLATION AND USAGE GUIDE__________________ 64
8-1 CMS Installation __________________________________________ 64
8-2 CMS LOGIN AND ENVIRONMENT____________________________ 66
8-3 DVRs, Groups & Events ___________________________________ 67
8-3.1 View DVR ／ Group List ________________________________ 67
8-3.2 View Event Logs _____________________________________ 68
8-4 Local PC Information and Control ___________________________ 69
8-5 Main Display _____________________________________________ 69
8-5.1 Audio Control________________________________________ 70
8-5.2 eMAP Display________________________________________ 70
8-5.3 PTZ Control _________________________________________ 72
8-6 Operation Bar ____________________________________________ 73
8-6.1 User administration ___________________________________ 73
8-6.2 DVR Administration___________________________________ 75
8-6.3 Group Administration _________________________________ 75
8-6.4 eMap Administration __________________________________ 76
8-6.5 Remote Play_________________________________________ 77
8-6.6 HDD Playback________________________________________ 78
8-6.7 File Playback ________________________________________ 78
8-6.8 Event Playback_______________________________________ 79
8-6.9 Snapshot Data _______________________________________ 81
8-6.10 Recording Data _____________________________________ 81
APPENDIX I I-DVR.NRT REGISTRATION ____________________________ 82
APPENDIX II DB 26 Definition (For 16CH DVR only) ____________________ 83
APPENDIX III Record Mode Comparison_______________________________ 84

5
CHAPTER 1 PACKING DETAIL AND INSTALLATION
1-1 PACKING
1. DVR
2. Quick Start 3. IR Remote Control 4.Batteries x2
5. CD 6. Hard Disk Mount x2 7. Screws x20
8. Power Adaptor 9. Power Cord 10. SATA Cord 2pcs
11.IDE to SATA Cable 12. DB 26 Flat Cables
(16ch only) (16ch only)
1-2 Hard Disk Installation
Step 1) Fix the HDD to rack mount with the screws as indicated.

6
Step 2) Place the HDD on the HDD plate and screw it as indicated.

7
Step 3) Connect the power and the SATA cables as indicated.
Note: After installation, please initialize Hard Disk before starting to record. For more detailed
information, please check out User Manual 4-9 System Tools for reference.
1-3 DVD-RW Installation
Step 1) Remove the front cover from DVR.

8
Step 2) Put the DVD-RW into the DVR as indicated by the arrow.
Step 3) Screw the bottom of the DVR as indicated to fix the DVD-RW.
Step 4) Connect the power and the SATA cables.

9
CHAPTER 2 PANEL LOCATION
2-1 FRONT PANEL CONTROLS
Control Keys
Description
○
1REC
Start or stop recording.
○
2PLAY
Play back in normal speed.
○
3PAUSE
Press , to pause playback.
○
4T-SRH
Display the search menu.
○
5STATUS
HDD status
⑥PTZ
PTZ setting(like direction arrow ,camera zoom and focus control)
○
7BACK UP
In LIVE mode, press to display menu. In PLAYBACK mode, press to pause
playback.
○
8ZOOM
In LIVE or PLAYBACK mode, enlarge the display of a channel.

10
○
9PIP
In LIVE mode, display with picture in picture format.
○
10 MENU
In LIVEmode, press to display menu. In PLAYBACK mode,
○
11 ／
In SETUP mode, press to reduce value. In PLAYBACK mode, press to play
rewind.
○
12 /SLOW
In SETUP mode, press to move cursor up. In PLAYBACK mode, press to
slow down.
○
13 /
In SETUP mode, press to increase value. In PLAYBACK mode press to
play forwards.
○
14 /
In SETUP mode, press to reduce value. In PLAYBACK mode, press to play
rewind.
○
15 OK
Mode switch ,pitch on or cancel check box
○
16 USB 2.0 Port
Port for USB external devices
○
17 USB 1.1 Port
Port for USB external devices.
2-2 16CH REAR PANEL CONNECTOR
○
1MAIN monitor
BNC port for the main monitor.
○
2SPOT monitor
BNC port to display full screen image of all installed cameras
in sequence.
○
3VIDEO IN
BNC input ports for cameras, 16 in total.
○
4AUDIO IN
RCA input port for audio signal. There are 4 ports available.
(corresponding to channel 1 to 4)
○
5VGA
VGA port.
○
6Fan
DC 12V 40mm X 40mm fan.
○
7DC 12V
Socket for a DC 12V input.
○
8POWER
Power switch.
○
9EXTERNAL I/O
EXTERNAL I/O port for DB 26 flat cables. (Please refer to
the APPENDIX Error! Reference source not found. for pin
definition.)
○
10 NTSC／PAL Switch
Switch between NTSC and PAL format.
○
11 LAN
Network port.
○
12 E-SATA
External SATA hard disks port.
⑬AUDIO OUT
RCA output for audio signal.
○
2
○
4
○
5
○
6
○
7
○
8
○
9
○
10
○
11
○
12
○
1
③
⑬
16

11
2-3 8CH REAR PANEL CONNECTORS
○
1SPOT monitor
BNC port to display full screen image of all installed cameras in
sequence.
○
2MAIN monitor
BNC port for the main monitor.
○
3VIDEO IN
BNC input ports for cameras, 8 in total.
○
4AUDIO IN
RCA input port for audio signal. There are 4 ports available.
(corresponding to channel 1 to 4)
○
5AUDIO OUT
RCA output port for audio signal.
○
6VGA
VGA port
○
7Fan
DC 12V 40mm X 40mm fan
○
8EXTERNAL I/O
EXTERNAL I/O port (see below for pin definition)
○
9LAN
Network port
○
10 DC 12V
Socket for a DC 12V input.

12
2-4 4CH REAR PANEL CONNECTORS
○
1SPOT monitor
BNC port to display full screen image of all installed cameras
in sequence.
○
2MAIN monitor
BNC port for the main monitor.
○
3VIDEO IN
BNC input ports for cameras, 4 in total.
○
4AUDIO IN
RCA input port for audio signal. There are 4 ports available.
(corresponding to channel 1 to 4)
○
5VGA
VGA port
○
6Fan
DC 12V 40mm X 40mm fan
○
7EXTERNAL I/O
EXTERNAL I/O port (see below for pin definition)
○
8LAN
Network port
○
9NTSC／PAL Switch
Switch between NTSC and PAL format.
○
10 DC 12V
Socket for a DC 12V input.

13
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS
The IR remote control and mouse operate differently under each mode; this chapter describes
the functions of them under three different modes: LIVE, PLAYBACK and PTZ.
3-1 LIVE Mode
You can monitor all the channels, listen to audio signal and have some related operations
under LIVE mode. This paragraph describes the IR remote control, mouse operation and on
screen graphical icons under LIVE mode.
Table 3-1.1 Functions of remote control under LIVE mode
Note：4CH will show quad display; 8 CH will show quad and 9-channel display.
Table 3-1.2Graphical icons that will display after right-clicking your mouse under LIVE
mode.
Icon
Description
Resting the cursor on this icon will bring up the following four menu icons.
Button
Description
REC
Start/Stop recording.
PLAY
Start playing back the most recently recorded segment.
LOCK
Enable/Disable the Keypad function
1,2,3,4
Select the channel to monitor in full screen
FREEZE
Turn on/off screen freeze function.
Switch to quad display.
Switch to 9-channel display. 4ch DVR doesn‟t feature this function.
Switch to 13-channel display. 4ch DVR doesn‟t feature this function.
Switch to 16-channel display. 4ch DVR doesn‟t feature this function.
ENTER/MODE
Switch to full screen, quad display.
MENU/
Enable/ Disable setup Menu.
BK-UP/ESC
Enable/ Disable backup menu.
SRH
Enable/ Disable search menu.
MUTE
Switch channel 1 output audio / turn off LIVE audio
STATUS
Enable/ Disable Status.
OSD
Turn on/off the screen display
Zoom/Zoom -
Enable/ Disable double screen size display. You can click on the channel
name for choosing a specific channel.
PIP/Zoom +
Turn on picture-in-picture format. Click on the channel name can switch to
other channels.
PTZ
Enable PTZ control.
AUTO
In AUTO mode, all available channels will be cycled through in full screen.
DVR1,2,3,4
Switch DVR ID1~4

14
Main menu.
Search menu.
Backup menu.
PTZ mode.
Turn on/off recording.
Playback.
Resting the cursor on this icon will bring up the following five display icons.
FREEZE.
PIP, picture in picture
ZOOM, double the screen size
AUTO-sequence
LOCK, activate the key lock.
Full screen display.
Quad display.
9-channel display.
Note：4CH will show quad display; 8 CH will show quad display and 9-channel display.
Table 3-1.3Description of on screen graphical icons in LIVE mode
Icon
Description
Recording is on
1~4
Live Audio is on
Live Audio is off
Motion detected on the channel
Sensor triggered on the channel

15
Video loss detected on the channel
USB device detected
DVD burner is detected
Connected to the LAN cable.
Timer recording is on
Red：Timer is set and recording has been started
White：Timer is set but recording has not yet been started
AUTO-seq is on
2X
2X zoom in is on
Freeze is on, screen is frozen
LOCK is on
PTZ control is on
1~8
IR remote signal has been set to 1-8 to correspond to your 1-to-8
remote control. Meanwhile, the standard remote control can‟t
control DVR under this situation. It can only be controlled
by1-to-4 or 1-to-8 remote controls (optional device).
Icon
Description
/
Image quality (High/Low)
/
Full screen
Record
Snap shot
Record and snap shot file saving path setup
3-2 PLAYBACK Mode
Switch to PLAYBACK mode by pressing “PLAY”under the LIVE mode, the graphical icon
will show up on the upper center of the screen and the operation panel ( see below picture)
will show up at right lower corner of the screen. You can drag the panel by mouse to place it
on any location of your screen.

16
Table 3-2.1 Remote control functions under the PLAYBACK mode
Button
Description
ENTER / MODE
Switch to full screen, quad, 9-channel or 16-channel display.
MENU /
Turn on/off PAUSE.
PLAY
Play back at normal speed.
/ SLOW
Play back at slower speed. The speed will be slowed to 1/2, 1/4, 1/8,
1/16 by each pressing of the button till the slowest limitation of 1/16 of
the normal speed. Current playback speed is shown in the upper
center of the screen.
/
Fast rewind. Each press increases the speed to the next level. There
are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.
/
Fast forward. Each press increases the speed to the next level. There
are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.
/
Stop playback.
Table 3-2.2 The mouse operation under the PLAYBACK mode.
Icon
Description
「/ 」Fast rewind
「/ 」Fast forward
／
Play/pause
「▢/ SLOW」， slow playback

17
「▼/ ■」stop playback
Playback channel by channel with snap shot display
Full screen display
Quad display
9-channel display
Zoom-in display
Note：4CH will show quad display; 8 CH will show quad display and 9-channel display.
3-3 PTZ Mode
Switch to the PTZ mode by pressing “PTZ”button under the LIVE mode. The PTZ icon
will appear on upper left side of screen and the control panel will appear on the down right side
of screen.
Table 3-3.1 Remote Control functions under the PTZ mode
Button
Description
/ SLOW
Move PTZ up.
/
Move PTZ down.
/
Move PTZ to the left.
/
Move PTZ to the right.
ZOOM +
PTZ zoom-in.
ZOOM -
PTZ zoom-out.
FOCUS +
PTZ focus-in.

18
FOCUS -
PTZ focus-out.
IRIS +
PTZ iris-open.
IRIS -
PTZ iris-close.
TOUR
Activate PTZ pre-set tour. ＊
PRESET+
Number
Setup the Preset location
Press “PRESET”key first then two-digit number; DVR will set the current
PTZ location at entered preset number.
PLAY+
Number
Go to Preset location
Press “PLAY”key first then two-digit number, PTZ will go to the
correspondent preset number location.
PIP
Set current PTZ location as the start of line-scan. ＊
FREEZE
Activate auto line-scan. ＊
ZOOM
Set current PTZ location as the end of line-scan.＊
＊PTZ communication protocols from different brands aren‟t compatible 100% sometimes.
Therefore, some of these functions may be unavailable.
Table 3-3.2 Mouse operation under the PTZ mode
Icon
Description
Leave PTZ Mode，back to the LIVE mode
Pre-set number N. (1~64)
Go to pre-set number N.
Set current PTZ location at pre-set number N.
「TOUR」， press to activate pre-set tour＊
「PIP」， Set current PTZ location as the start
of line-scan. ＊
「FREEZE」， Activate line-scan. ＊
「ZOOM」， Set current PTZ location as the end
of line-scan. ＊
To move PTZ in 360°
PTZ zoom in; PTZ zoom out
PTZ focus in; PTZ focus out.
PTZ IRIS open, PTZ IRIS close.

19
Below functions need support from specific PTZ manufacturer.
Please check user manual of your PTZ for more detail.
AUX 1,「AUTO」Key ＋Number key「1」
AUX 2,「AUTO」Key ＋Number key「2」
AUX 3,「AUTO」Key ＋Number key「3」
AUX 4,「AUTO」Key ＋Number key「4」
AUX 5,「AUTO」Key ＋Number key「5」
AUX 6,「AUTO」Key ＋Number key「6」
AUX 7,「AUTO」Key ＋Number key「7」
AUX 8,「AUTO」Key ＋Number key「8」
「Backup」, Customized function。
＊PTZ communication protocols from different brands aren‟t compatible 100%
sometimes. Therefore, some of these functions may be unavailable.
CHAPTER 4 MAIN MENU SETUP
To enter the main menu and set up DVR, log-in account and user password are required.
The default password of the administrator is “123456”. Please check the “Account Setup”for
related setup of other log-in users.
Table 4-0.1 Some definition of virtual keyboard.
Item
Description
Switch between capital and small letters.
/
Switch between numbers and letters.
Press to cancel the setup, and re-choose the login
account.

20
Delete the last character.
Enter to identify the password. It will enter the set
up menu, If the password is verified.
Space key
Table 4-0.2 The operation of remote control under the setting menu
Item
Description
Switch to different options under one item
Switch to different items
MENU
Save setup and back to LIVE mode
ESC
Back to Upper level of menu without saving
ENTER
Enter the menu, or display virtual keyboard
PS. The initialization of new-installed HD is required before recording, please refer to “4-9
UTILITY SETUP”for detail.