SCALE-PARKFLYER Beriev Be200 Instructions for use

Scale-parkflyer.de
Beriev
Be200
Construction manual
Part 1

.
Beriev Be 200
Beriev Be 200Beriev Be 200
Beriev Be 200
by Scale-Parkflyer.de
Material List
Part No. Title piece Material
Rumpf:
R1 / R2 Frame side front / back each 2
X 6 mm Depron
R3 / R4 Frame up front / back each 1 X 6 mm Depron
R5 / R6 Frame low front / back each 1 X 6 mm Depron
S1 Frame Hull 1 X 3 mm Depron
S2 - S10 Frames Hull each 1 X 6 mm Depron
S10b Frame Hull 1 X 1,5 mm wood
S10c Half - Frame Hull 2 X 6 mm Depron
S11 / S12 Frame Hull each 1 X 6 mm Depron
S12 a Reinforcement 4 X 6 mm Depron
S12 b Reinforcement 2 X 6 mm Depron
S13 Frame Hull 1 X 6 mm Depron
S13b Frame Hull 1 X 1,5 mm wood
S13c Half - Frame Hull 2 X 6 mm Depron
S14 - R19 Frame Hull each 1 X 6 mm Depron
R7a-d Hull Nose each 1 X 6 mm Depron

R8 Border reinforcement 2 X 6 mm Depron
R9 Overlay for Wing 1 X 6 mm Depron
R10 Overlay for Wing Wood 1 X 0,8 mm wood
R11 Landing Gear box low 2 X 6 mm Depron
R12 Landing Gear box side 2 X 6 mm Depron
R13 Landing Gear box back 2 X 6 mm Depron
R14 Landing Gear box front 2 X 6 mm Depron
R15 Border reinforcement 2 X 6 mm Depron
R16 Support for Power Unit 2 X 6 mm Depron
R17 Support for Power Unit Reinforcement 2 X 0,8 mm wood
R18 Support for Power Unit Reinforcement 2 X 10X2X262 mm wood
R19 Support for Power Unit low 2 X 3 mm Depron
R20 Support for Power Unit side 4 X 6 mm Depron
R21 Cover Support for Power Unit 4 X 6 mm Depron
R22 Cover Support for Power Unit 1 X 0,8 mm wood
R23 Cover Support for Power Unit Front 1 X 6 mm Depron
R24 Bridge Hull Cover front 1 X 6 mm Depron
R25 front Hull Cover up 1 X 3 mm Depron
R26 front Hull Cover side 2 X 6 mm Depron
R27 Reforcement Rail for R26 2 X 6 mm Depron
R28 front Hull Cover low 2 X 6 mm Depron
R29 Hull Cover Material 5 X 1000x250x3 mm wood
R30 Step 1 X 3 mm Depron
Power Unit:
R29 Turbine Pipe inside 2 X 3 mm Depron
R30 Turbine Pipe outside 2 X 6 mm Depron
R31 Template inside pipe 2 X 6 mm Depron
R32 Template inside pipe 2 X 6 mm Depron
R33 Turbine outlet 2 X 3 mm Depron
R34 Engine Support 6 X 6 mm Depron
R35 Engine Support Reinforcement 2 X 1,5 mm wood
Tail:
L1 Tail 2 X 3 mm Depron two Parts
L2 Reinforcement Elevation 2 X 1,5 mm wood
L3 Tail Reinforcement 2 X 10X2 mm Pine X 350 mm
L4 Tail front 2 X 6 mm Depron
L5 Rudder box cover 1 X 3 mm Depron
L6 Tail Cover 1 X 6 mm Depron
L7 Tail Cover up 1 X 6 mm Depron
L8 Molding Tail front 2 X 6 mm Depron
L9 Rib 1 X 3 mm Depron
L10 Ribs 4 X 3 mm Depron
L11 Ribs 5 X 3 mm Depron
L12 Elevator part inside 2 X 6 mm Depron
L13 Elevator part outside 4 X 3 mm Depron
L14 Stream sheet 2 X 6 mm Depron
ing:
T1 Wing ground 2 X 3 mm Depron
T2 Main support 2 X 6 mm Depron
T3 Reforcement Main Support 2 X 1,5 mm wood
T4 Reforcement second Support 1 X 1,5 mm wood
T5 Second Support 1 X 6 mm Depron
T6 / T7 Reforcement Aileron each 2
X 6 mm Depron
T8 Nose strip inside 4 X 6 mm Depron

T9 Nose strip outside 2 X 6 mm Depron
T10 Wingtip 4 X 6 mm Depron
R1 Rib 1 X 6 mm Depron
R2 - R7 Ribs each 2 X 6 mm Depron
R8 / R9 Ribs each 2 X 3 mm Depron
R10 Rib each 2 X 6 mm Depron
R10a Reforcement for Rib 4 X 1,5 mm Depron
R11 / R12 Rib each 2 X 3 mm Depron
T13 Flap Casing each 2 X 3 + 6 mm Depron
T14 Flap Casing each 4
X 3 + 6 mm Depron
T15 Flap Casing each 2 X 3 + 6 mm Depron
T16 Flap Casing each 2 X 3 + 6 mm Depron
T17 Reforcement for Floats 2 X 1,5 mm wood
T18 shank for floats 4 X 6 mm Depron
T19 Float segment 4 X 6 mm Depron
T20 Float segment 4 X 6 mm Depron
T21 Float segment 4 X 6 mm Depron
T22 Wing Cover front 1 X 3 mm Depron
T23 Wing Cover front 1 X 0,8 mm wood
T24 Rib Cover outside 2 X 6 mm Depron
T25 Rib Cover inside 3 X 6 mm Depron
T26 Rb Cover back 1 X 6 mm Depron
T27 Cover back 1 X 3 mm Depron
T28 Wing cover up 2 X 3 mm Depron
RC Equipments:
Glue Recommendation: Epoxy / solvent free glues
glas fiber roof for any reinforces ca. 150x150 mm
Two-side Tape for fixing Hull on Heling
Elevation Angle 2 X 6/5 x 65mm Alu-pipe
Elevation Angle 1 X 6/5 x 25mm Alu-pipe
Elevation Angle 1 X 5 mm x 160mm Carbon Pipe
Rudder bar 2 X 4/3 x 10mm Alu-pipe
Rudder bar 1 X 3 mm x 36mm Carbon full
Rudder bar 1 X 6x3x220 mm pine
Fan Recommendation:
EDF Fan Brushless ADF64-300 XL 2 X 5250kv / 400 W, 8-Blades

Construction manual, Part 1
1. Frame R5 and R6 stick together.
2. Check for a perfect fit all Rib / Frame parts. ( without any glue )

3. Put together Frames S2-S9 and S14-S19.
4. Put together wood Parts each on the wing side on the FrameR10 and R13
S10b and S13b. S10 until S13 Frame put together in Hull.

5. Side Frame R1 and R2 put in the Hull without twist..

6. For a perfect Hull without any twists, please take a Heeling in wood or see
here in 6 mm Depron ( its easy ) You can fix all bars with two-sides tapes.

8. The Spacer have got follows lenght: Rear Part: 120,5 mm, in the Front: 88,5
mm.

9. Half-Frames S10c and S13c put in..
10. S 12a/b parts put together for one Part.

11. Frame S1 put in the front of the Hull.

12. Planking the Hull:
The Hull please cover with 3 mm Depron. For a perfect finish, please follow
next steps: Please flex the Depron Material in the right direction before. Its
going easy with a commercial Hairdryer ( min. 1000 Watt ). Take only one
Segment from Frame to Frame. I like to glue with Epoxy, because the 5
minutes is enough to fix it by Hand. Tape to fix isn’t good for any bumps.
Please wait for planking by Frame: S3/4 and S7/8, S15/16 and from S17
until all Frames behind them:

A bent Segment

13. Please take a cut between R13 and R13b for pine wood R17/R18
( 10x2x262 mm ).

14. Please cut out space for pine wood.