Scanivalve DSA3217-PTP Series Operation manual

DSA3217-PTP/3218-PTP





iv
DSA3200-PTP
iv
Product
Preface
PREFACE

The WARNING! symbol indicates that danger of injury for persons and the environment and/or
considerable damage (mortal danger, danger of injury) will occur if the respecve safety precau-
ons are not taken.
The CAUTION ! symbol indicates danger for the system and material if the respecve safety precau-
ons are not taken.
The ESD note symbol indicates that proper precauons for handling Electrostac Sensive Devices
needs to be taken when performing the related operaon. This includes the use of grounded work
surfaces and personal wrist straps to prevent damage to sensive electronic components.

Scanivalve Corporaon, Liberty Lake, Washing-
ton, hereaer referred to as Seller, warrants to the Buyer
and the rst end user that its products will be free from
defects in workmanship and materi al for a period of twelve
(12) months from date of delivery. Wrien noce of any
claimed defect must be received by Seller within thirty
(30) days aer such defect is rst discovered. The claimed
defecve product must be returned by prepaid transporta-
on to Seller within ninety (90) days aer the defect is rst
discovered. Seller’s obligaons under this Warranty are
limited to repairing or replacing, at its opon, any product
or component part thereof that is proven to be other than
as herein warranted.
Surface transportaon charges covering any
repaired or replacement product or component part shall
be at Seller’s expense; however, inspecon, tesng and
return transportaon charges covering any product or com-
ponent part returned and redelivered, which proves
not to be defecve, shall be at the expense of Buyer or the
end user, whichever has returned such product or compo-
nent part.
This Warranty does not extend to any Seller product
or component part thereof which has been subjected to
misuse, accident or improper installaon, maintenance or
applicaon; or to any product or component part thereof
which has been repaired or altered outside of Seller’s facili-
es unless authorized in wri ng by Seller, or unless such
installaon, repair or alteraon is performed by Seller; or
to any labor charges whatsoever, whether for removal and/
or reinstallaon of the defecve pro duct or component
part or otherwise, except for Seller’s labor charges for
repair or replacement in accordance with the Warran ty.
Any repaired or replacement product or component part
thereof provided by Seller under this Warranty shall, upon
redelivery to Buyer, be warranted for the unexpired poron
of the original product warranty.

v
DSA3200-PTP
v
Product Preface
v
THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, ARISING BY
OPERATION OF LAW OR OTHERWISE, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, AND IN NO EVENT SHALL
SELLER BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
In the event of a failure:
1) Nofy Scanivalve Corporaon, Customer Service
De partment. Include model number and serial number.
On receipt of this informaon, service data or shipping
instrucons will be forwarded. This may be transacted by
telephone or e-mail.
2) On receipt of shipping instrucons, forward the
pro duct, transportaon prepaid. Repairs will be made and
the product returned.
3) All shipments should be made via “Best Way”.
The product should be shipped in the original packing con-
tainer or wrapped in protecve material and surrounded by
a minimum of four (4) inches of a shock absorbing material.

Scanivalve is a registered trademark of Scanivalve Corpora-
on.
All other brand and product names are trademarks or regis-
tered trademarks of their respecve companies.

If the product must be shipped, whether being returned
to Scanivalve or relocated to another locaon it must be
packaged properly to minimize the risk of damage. The
recommended method of packing is to place the instru-
ment in a container, surrounded on all sides with at lease
four inches of shock aenuang material such as Styrofoam
peanuts.

Please note that the product specicaons and other
informaon contained in this manual are subject to change
without noce. Scanivalve Corporaon makes an eort and
strives to provide complete and current informaon for the
proper use of the equipment. If there are any quesons
regarding this manual or the proper use of the equipment,
contact Scanivalve Corporaon.

If there are any quesons or concerns regarding any Sca-
nivalve product please do not hesitate to contact us at the
following:
Scanivalve Corp.
1722 N. Madson Street
Liberty Lake, WA 99019
Telephone: [phone] [phone]
Fax: [phone]
[e-mail]
www.scanivalve.com
Scanivalve Corporaon is an ISO9001:2015 cered
company.

vi
DSA3200-PTP
vi
Table of Contents
[INTENTIONALLY LEFT BLANK]

vii
DSA3200-PTP
vii
Table of Contents

 
Warnings, Cauons and Notes iv
Warranty iv
Trademarks ® and Copyrights © v
Packaging for Shipment v
Important Noce v
Contact Informaon v
 
DSA3217-PTP 1
DSA3218-PTP 2
 
General Descripon 5
Module Overview 5
DAS3217-PTP Conguraons 5
DSA3217-PTP/16Px 5
DSA3217-PTP/16Px - Dual Range 6
DSA3217-PTP/8DPx - Dierenal 6
DSA3217-PTP/16Px - Absolute 6
DSA3217-PTP/16Px - Individual Reference 7
DSA3218-PTP Conguraons 8
DSA3218-PTP/16Px 8
DSA3218-PTP/16Px - Dual Range 8
DSA3218-PTP/8DPx - Dierenal 8
DSA3218-PTP/16Px - Absolute 9
DSA3218-PTP Heater Opon 9
DSA3218-PTP Cooling Kit Opon 9
Environmental Consideraons 10
 
Unpack & Inventory 11
Mounng 11
Warm-up 11
Communicaons 11
Serial Communicaons 11
Ethernet Communicaons 12
Client/Host Opons 12
PC - TCP/IP 12
PC - UDP 13
PC - ScanTel 13
PC - LabVIEW Conguraon Ulity 13
PC - LabVIEW Development Kit 13
PC - HyperTerminal 13
Zero Oset Calibraon 13

viii
DSA3200-PTP
viii
Table of Contents
Quick Zero Jumper 14
Scanning 14
Scanning With An External Trigger 14
Hardware Trigger 14
Soware Trigger 14
Freon Applicaon Operaons 15
 
Pneumac Connecons 16
Making 1/16” Tubulaon Connecons 16
Pressure Measurement (Px) Ports 17
Calibraon (CAL) Port 17
Reference (REF) Port 17
Control 1 (CLT1) Port 17
Control 2 (CTL2) Port 17
Control Supply (CTL SUPPLY or CTL) 17
Return (RTN) Port 17
Purge Control (PRGCTL) Port 18
Purge Supply (PRG) Port 18
Power Requirements 18
Calibraon Valve 18
 
DSA-PTP Control and Conguraon 20
DSA-PTP Commands 20
Command List 21
Calibrate Barometric Pressure 21
Clear 21
Calibrate Zero 22
Delete 23
Digital Out 23
Error 23
Insert 24
List All 25
List All Ranges 26
List Calibrate 27
List Delta 27
LIST FTP Sengs (LIST FTP) 28
List Gain 28
List Idencaon 29
LIST IP Sengs (LIST IP) 29
List Master 30
List MAXn Pressures 31
List MINn Pressures 31
List Negave Points 32
List Oset 32
List PTP Variables 33
List Scan 33
List Temperature 34
List Zero 34
Save 34

ix
DSA3200-PTP
ix
Table of Contents
Scan 35
Scan Trigger 36
Set 36
Status 36
Stop 37
Version 37
Set PTP Time 37
Get PTP Time 38
Get UTC Oset 38
Conguraon Variables 39
Scan Variables (LIST S) 39
Average (AVG) 39
Binary Data (BIN) 39
Unit Conversion Factor (CVTUNIT) 39
Engineering Units (EU) 40
Data Format (FORMAT) 40
Frames Per Scan (FPS) 40
Page (PAGE) 41
Period (PERIOD) 41
QPKTS 41
Data Sample Source (SIM) 41
Time Stamp (TIME) 42
Scan Unit (UNITSCAN) 42
Enable External Trigger (XSCANTRIG) 42
Zero Correcon (ZC) 43
IP Variables (LIST IP) 44
IP Address (IPADD) 44
Subnet Mask (SUBNET) 44
MAC Address (MAC) 44
LOGIN (LOGIN) 44
Password (PASSWORD) 45
Login 1(LOGIN1) 45
Password 1(PASSWORD1) 45
Anonymous Logon (ALLOWANON) 45
Applicaon (APP) 45
Set Gateway (GW) 46
PTP Variables (LIST PTP) 47
PTP Enable (PTPEN) 47
PTP Stascs (STAT) 47
Scan Start Time (SST) 47
Scan Start Date (SSD) 48
UTC Oset (UTCOFFSET) 48
FTP Variables (LIST FTP) 49
FTP User Name (UESRFTP) 49
FTP Password (PASSFTP) 49
Enable FTP (ENFTP) 49
FTP File Path (PATHFTP) 49
FTP IP Address(IPFTP) 49
FTP File Name(FILEFTP) 50
Pressure Variables (LIST B, LIST H, LIST L and LIST N) 51
Absolute Enable (ABSn) 51
Maximum Pressure (MAXn) 51
Minimum Pressure (MINn) 51

x
DSA3200-PTP
x
Table of Contents
Negave Calibraon Points (NEGPTSn) 51
Calibraon Variables (LIST C) 52
Channel 1-8 Number of Negave Calibraon Points (NEGPTSL) 52
Channel 9-16 Number of Negave Calibraon Points (NEGTPSH) 52
Channel 1-8 Maximum Pressure (PMAXL) 52
Channel 9-16 Maximum Pressure (PMAXH) 52
Channel 1-8 Minimum Pressure (PMINL) 53
Channel 9-16 Minimum Pressure (PMINH) 53
Error Limit Variables (LIST LIMIT) 54
High Temperature Error Limit (THI) 54
Low Temperature Error Limit (TLOW) 54
High Pressure Error Limit (PHI) 54
Low Pressure Error Limit (PLOW) 54
Idencaon Variables (LIST I) 55
Serial Echo (ECHO) 55
Model (MODEL) 55
Ethernet Port (PORT) 55
Ethernet Host (HOST) 56
Pressure Deltas (LIST D) 56
Deltas (DELTAn) 56
Zero Osets (LIST Z) 56
Zero Oset (ZEROn) 56
DSA-PTP Packet Denions 57
Packet Types 57
Host to DSA-PTP Command Packet 57
Status Packet 57
Scan Raw Packet 57
Scan EU Packet 58
Scan Raw with Time Packet 58
Scan EU with Time Packet 58
Scan EU Packet with FPT - Floang Point Temperature (SET EU 2) 58
Scan RAW/EU with PTP Time (SET TIME 3) 59
ASCII Packet 59
ASCII Packet Examples 60
Network Protocols Supported 60
DSA3200-PTP Boot Parameters 60
Changing Boot Parameters (including IP address) 60
DSA3200-PTP Buer Descripon 61
DSA-PTP Network Conguraons 61
Isolated Network 61
Integrated with System Network 61
Sub-Network with Gateway 61
DSA-PTP Network Addressing 61
 
Calibraon 62
Full Calibraons 62
Field Calibraons 62
Zero Oset Calibraon 62
Special Procedures 63
Internet Explorer Setup 63

xi
DSA3200-PTP
xi
Table of Contents
DSA-PTP Firmware Installaon (Windows 7 & 10) 63
DSA-PTP Coecient Upload 64
DSA3200-PTP Sensor Replacement 65
DSA3200-PTP General Checkout Procedure 68
 
Appendix A: Temperature Compensated Pressure Conversion 71
Appendix B: Engineering Unit Conversion Constants 72
Appendix C: DSA3200-PTP Error List 73
Boot/Inializaon Errors 73
Set Conguraon Variable Errors 73
Command Errors 75
Communicaon Errors 76
Appendix D: Soware Change Log 78

xii
DSA3200-PTP
xii
Section 1: Specifications
[INTENTIONALLY LEFT BLANK]

1
DSA3200-PTP
1
Section 1: Specifications
DSA3200

DSA3217-PTP
Size (WxHxD) 2.86” x 3.40” x 7.08”
(7.26cm x 8.64cm x 17.98cm)
Weight 6.4lbs
(2.91kg)
Pressure Inputs: 16 (Standard)
8 (True Dierenal)
Input Fings:
Pressure Inputs .063” tubulaons
Control Inputs .063” tubulaons
Full Scale Ranges (standard)
Dierenal ±5”WC, ±10”WC,
±20”WC, 1 , 2.5, 5, 15,
30, 50, 100, 250, 500,
750 psid
(1.25, 2.5, 5, 7, 17, 35,
100, 210, 345, 700, 1725,
3500, 5170 kPa)
Absolute 15, 30, 50, 100 and
250 psia
(100, 210, 345, 700 and
1725 kPa)
Accuracy (aer calibraon)*
Dierenal
5 inH2O ±0.40% FS
10 inH2O ±0.20% FS
20 inH2O ±0.20% FS
1.0 psid ±0.12% FS
2.5 psid ±0.08% FS
5 to 500 psid ±0.05% FS
501 to 750 psid ±0.08% FS
Absolute (With CALB performed)
15 psia ±0.05% FS
30 psia ±0.05% FS
50 psia ±0.05% FS
100 psia ±0.05% FS
250 psia ±0.05% FS
*Some combinaons of pressure ranges in dual-range
modules may dictate a reducon in accuracy
Overpressure Capacity (No damage)
5 inH2O 2 psi
10 inH2O 2 psi
20 inH2O 2 psi
1 psid 5 psi
2.5 to 499 psid 200%
500 psid 150%
750 psid 113%
Maximum Reference Pressure 250 psid (1750 kPa) or
sensor overpressure,
which ever is less
Power Requirements 20 to 36 Vdc at 8 W
I/O and mang connectors
Ethernet 100Base-T RJ45
Trigger (bulkhead) PT02A-8-2P
Trigger (mang) PT06A-8-2S-SR
Trigger (bulkhead) JTP02RE8-6P
Trigger (mang) JTO1RE8-6S-SR
Power (bulkhead) PTO2A-8-3P
Power (mang) PTO6A-8-3S-SR
Communicaons Protocol Ethernet IEEE802.3
Typical Data Acquision Rate*
TCP/IP ASCII 50 samples/chan/sec
UDP Binary 850 samples/chan/sec
*Maximum data output depends on network
Typical Communicaons Rate
Ethernet 100 Mbits/sec
RS232 9600 BAUD
(Conguraon only)
Operang Temperature 0 to 60 °C
Compensated Range 0 to 72 °C
Total Thermal Error Less than ±0.001% FS
Humidity
Operaon 5 to 95% RH, Non-Condensing
Storage 5 to 95% RH, Non-Condensing
Shock & Vibraon MIL-STD-810D Curve H
Shock 10G
Vibraon 10G
Acceleraon 10G
Media Gasses compable with
Silicon, Silicone,
Aluminum and Stainless
Steel
Precision Time Protocol IEEE-1588 PTPv2

2
DSA3200-PTP
2
Section 1: Specifications
DSA3218-PTP
Size (WxHxD) 4.08” x 6.97” x 9.0”
(10.36 cm x 17.70 cm x 22.86 cm)
Weight 9.78 lbs
(4.45 kg)
Pressure Inputs: 16 (Standard)
8 (True Dierenal)
Input Fings:
Pressure Inputs 1/8” SwageLok®
(1/16” and 1/4” oponal)
Control Inputs 1/8” SwageLok®
(1/16” and 1/4” oponal)
Full Scale Ranges
Dierenal ±5”WC, ±10”WC,
±20”WC, 1 , 2.5, 5, 15,
30, 50, 100, 250, 500,
750 psid
(1.25, 2.5, 5, 7, 17, 35,
100, 210, 345, 700, 1725,
3500, 5170 kPa)
Absolute 15, 30, 50, 100 and
250 psia
(100, 210, 345, 700 and
1725 kPa)
Accuracy (aer calibraon)*
Dierenal
5 inH2O ±0.40% FS
10 inH2O ±0.20% FS
20 inH2O ±0.20% FS
1.0 psid ±0.12% FS
2.5 psid ±0.08% FS
5 to 500 psid ±0.05% FS
501 to 750 psid ±0.08% FS
Absolute (With CALB performed)
15 psia ±0.05% FS
30 psia ±0.05% FS
50 psia ±0.05% FS
100 psia ±0.05% FS
250 psia ±0.05% FS
*Some combinaons of pressure ranges in dual-range modules
may dictate a reducon in accuracy
Overpressure Capacity (No damage)
5 inH2O 2psi
10 inH2O 2psi
20 inH2O 2psi
1.0 psid 5psi
2.5 to 499 psid 200%
500 psid 150%
750 psid 113%
Maximum Reference Pressure 250 psid (1750 kPa) or
sensor overpressure,
which ever is less
Power Requirements
No Heater 20 to 36 Vdc at 8 W
With Heater 20 to 36 Vdc at 40 W
(Drops to 8 W aer
module has reached
temperature)
I/O and mang connectors
Ethernet 100Base-T D-Code M12
Trigger (bulkhead) PT02A-8-2P
Trigger (mang) PT06A-8-2S-SR
Trigger (bulkhead) JTP02RE8-6P
Trigger (mang) JTO1RE8-6S-SR
Power (bulkhead) PTO2A-8-3P
Power (mang) PTO6A-8-3S-SR
Communicaons Protocol Ethernet IEEE802.3
Typical Data Acquision Rate*
TCP/IP ASCII 50 samples/chan/sec
UDP Binary 850 samples/chan/sec
*Maximum data output depends on network
Typical Communicaons Rate
Ethernet 100 Mbits/sec
RS232 9600 BAUD
(Conguraon only
Operang Temperature
Without Heater 0 to 60 °C
With Heater -55 to 60 °C
(Cooling kit recommended above 55 °C)
Compensated Range 0 to 72 °C
Total Thermal Error Less than ±0.001% FS
Humidity
Operaon 5 to 95% RH, Non-Condensing
Storage 5 to 95% RH, Non-Condensing
Shock & Vibraon MIL-STD-810D Curve H
Shock 10G
Vibraon 10G
Acceleraon 10G
Media Gasses compable with Silicon,
Silicone, Aluminum and Stainless
Steel
Precision Time Protocol IEEE-1588PTP v2

3
3
Section 1: Specifications
DSA3200-PTP


4
DSA3200-PTP
4
Section 1: Specifications


5
DSA3200-PTP
5
Section 2: Introduction


The Digital Sensor Array (DSA) is a stand-alone electronic
pressure scanner which can accept up to 16 pneumac
inputs. The module is specically designed for use in appli-
caons where long calibraon intervals, simple operaon
and high accuracy are required. Each DSA-PTP incorporates
16 individual, temperature compensated, piezoresisve
pressure sensors, an A/D converter and a microproces-
sor. Each pressure sensor is characterized over pressure
and temperature. This informaon is stored in EEPROM
memory and enables the module to directly output cor-
rected data in engineering units.
The sensors within each DSA3200-PTP series module are
arranged in groups of eight (8). Each block of eight (8)
sensors has its own calibraon valve. This calibraon valve
has four (4) modes of operaon and allows the DSA-PTP
module to perform measurement, calibraon and purge
funcons. The four (4) modes are:
• Measure
• Calibrate
• Isolate
• Purge
The calibraon valve mode is selected by applying 90-120
psi control pressure conguraons unique for each
operaon mode. The DSA-PTP calibraon valve ulizes
“Normally Px” valve logic where the valve defaults to
the measurement mode when no control pressures are
applied.

The DSA3200-PTP series is available in two basic congu-
raons; the DSA3217-PTP and the DSA3218-PTP. Both
conguraons oer 16 pressure inputs, both operate using
the same soware commands and both oer corrected
data output directly in engineering units. The dierence
between the modules is the packaging and the intended
applicaons. The DSA3217-PTP is enclosed in a stain-
less steel, splash resistant enclosure intended for most
laboratory, educaonal or controlled environments. The
DSA3218-PTP however, is enclosed in a stainless steel,
splash resistant, shock mounted enclosure with Swagelok®
ngs on all pneumac connecons. It is intended for
applicaons such as gas turbine tesng, ight tesng,
industrial applicaons and other more rugged environ-
ments.
In addion to the more rugged casing on the DSA3218-PTP
modules, addional opons of a heater or a cooling kit are
oered. The heater opon allows the module to be oper-
ated below the 0 °C temperature compensaon range of
the standard DSA3218-PTP or DSA3217-PTP modules. The
cooling kit is recommended for applicaons where the
ambient environment temperatures are likely to exceed 55
°C.
Both DSA3217-PTP and DSA3218-PTP modules are avail-
able with a variety of sensor conguraons. The standard
conguraon is 16 channels of the same pressure range,
however modules can be congured as dual-range units
with 8 channels of one pressure range and 8 channels of
another pressure range, ‘True-Dierenal’ measurement
modules which provide 8 channels of dierenal pressure
measurement, absolute pressure measurement modules
or units with individual reference ports for each sensor
(DSA3217-PTP only).

The DSA3217-PTP is available in 5 basic conguraons.

The basic DSA3217-PTP/16Px module provides 16 chan-
nels of the same ‘gauge’ pressure range sensors. These 16
pressure transducers are congured into two (2) groups of
eight (8) each. Each group of eight (8) transducers shares a
common calibraon valve and a common reference mani-
fold. Single range modules e the two reference manifolds
together and the two calibraon valves to provide the
user with a single reference and a single calibraon port to
connect to. Figure 2.1 depicts the top panel of a standard
DSA3217-PTP/16Px.


6
DSA3200-PTP
6
Section 2: Introduction

The DSA3217-PTP/16Px module is available as a dual-range
module, oering eight (8) channels of one pressure range
and eight (8) channels of a dierent pressure range. Like a
standard DSA3217-PTP, each group of eight (8) transducers
share a common calibraon valve and a common reference
manifold. However, in dual range modules the reference
manifolds and the calibraon valves are not ed together
and separate reference and calibraon ports are provided
on the top of the module. They are labeled CAL, CAL B, REF
and REF B. Figure 2.2 depicts the top panel of a dual range
DSA3217-PTP/16Px module.



For dierenal pressure measurement applicaons, the
DSA3217-PTP can be congured with eight (8) dieren-
al pressure transducers. They are arranged into two (2)
groups of four (4) transducers. Like the DSA3217-PTP/16Px,
each group of transducers has a dedicated calibraon valve
that allows the input pressures to be blocked o during any
calibraon, including a zero oset calibraon (CALZ). Figure
2.3 depicts the top panel of a DSA3217-PTP/8DPx module.

The DSA3217-PTP/16Px module can be used for absolute
pressure measurement when equipped with absolute pres-
sure transducers. A calibraon valve is provided for each
group of eight (8) sensors. All sixteen (16) transducers are
ed a single calibraon port, except in the cases of dual-
range absolute modules. Figure 2.4 depicts the top panel
of a DSA3217-PTP/16Px absolute pressure module.





7
DSA3200-PTP
7
Section 2: Introduction

Both the standard DSA3217-PTP/16Px and Dual Range
DSA3217-PTP/16Px are available with individual reference
ports for each sensor. A calibraon valve is provided for
each group of eight (8) sensors, however unlike the stan-
dard DSA3217-PTP/16Px modules a separate reference port
is provided for all sixteen (16) transducers. These indi-
vidual reference ports are not controlled by the calibraon
valve.

This means that any calibraon, including a zero oset
calibraon (CALZ) will have to be done with no pressure
applied to the module. The individual reference modica-
on is depicted in Figure 2.5 below.

8
DSA3200-PTP
8
Section 2: Introduction

The DSA3218-PTP is available in 4 basic pressure congura-
ons and has 2 oponal hardware conguraons.

The basic DSA3218-PTP/16Px module provides 16 chan-
nels of the same ‘gauge’ pressure range sensors. These 16
pressure transducers are congured into two (2) groups of
eight (8) each. Each group of eight (8) transducers shares a
common calibraon valve and a common reference mani-
fold. Single range modules e the two reference manifolds
together and the two calibraon valves to provide the
user with a single reference and a single calibraon port to
connect to. Figure 2.8 depicts the top panel of a standard
DSA3217-PTP/16Px.


The DSA3218-PTP/16Px module is available as a dual-range
module, oering eight (8) channels of one pressure range
and eight (8) channels of a dierent pressure range. Like a
standard DSA3218-PTP, each group of eight (8) transducers
share a common calibraon valve and a common reference
manifold. However, in dual range modules the reference
manifolds and the calibraon valves are not ed together
and separate reference and calibraon ports are provided
on the top of the module. They are labeled CAL A, CAL B,
REF A and REF B. Figure 2.9 depicts the top panel of a dual
range DSA3218-PTP/16Px module.



For dierenal pressure measurement applicaons, the
DSA3218-PTP can be congured with eight (8) dieren-
al pressure transducers. They are arranged into two (2)
groups of four (4) transducers. Like the DSA3218-PTP/16Px,
each group of transducers has a dedicated calibraon valve.
Figure 2.10 depicts the top panel of a DSA3218-PTP/8DPx
module.
 -
