Scanivalve MPS4200 User manual

MPS4200 Quick Start Guide
Step 1: Unpack & Inventory
When you rst unpack the MPS4200, begin by inspecng
and inventorying the contents of the package. If any visible
damage is immediately noced or if any contents are miss-
ing, contact Scanivalve before proceeding. Modules ship
standard with:
1) MPS4200 Module in case
2) Cercate of calibraon
3) MPS Resource Disk (USB Drive)
5) Power Cable with ying leads
6) Ethernet Cable with female RJ45
There may be other cabling or accessories included with
your order.
Step 2: Connect Ethernet Cable
Connect the provided MPS Ethernet cable to the MPS Ether-
net port. The cable will latch into the connector.
The standard cable provides a female RJ45 connecon. This
allows for a standard RJ45 Cat5e or beer Ethernet cable to
connect the MPS to a Ethernet hub or switch, or directly to a
host computer or laptop.
Step 3: Connect Ethernet Cable
Connect the provided MPS ying leads power cable to the
MPS power port. The cable will latch into the connector. The
ying leads end can be connected to a compable DC power
supply (5 to 36VDC @ 3.5W). See the wiring diagram on the
right for lead connecons (Red and Black).
CAUTION! Do not make or
break the power connector
with power applied! Doing so
risks damage to the module.
If an AC to DC power supply is provided (PDM series), con-
nect the power cable before powering on the power supply.
Once all connecons are made, apply power to the MPS and
allow the module enough me to boot. The Power, Link and
LAN lights should all light.
Step 4: Setup the Host Computer
In order to communicate withe MPS modules, the host com-
puter must be congured to be compable with the MPS.
The default MPS4200 IP address is:
MPS4200 and Standard Accessories
MPS4200 Cable Connections
to DC Power
to Ethernet
.TF3
8
7
6
5
4
3
2
1
123
3
2
4
54
6
1
2
3
5
6
7
8
4
ROTACOLREBMUNTRAP
SNOISIVER
1
5
A526551
SDAELGNIYLF/W
ELBACREGGIRT/REWOPSPM
:VERLEDOMA
REENIGNE
DEKCEHC
NWARD
EMANETAD
1-NOITPIRCSED METI .ON 359-A
:ELTIT
EZIS .ON.GWD VER
:#ORE 1FO1TEEHS
:ELACS
GNIWARDYLBMESSA
HJC
HS
6102SKROWDILOS:DAC
HJC
-
evlavinacS
KLB
DER
NRG
THW
GIRT+
GIRT-
NIV63-5
NTR63-5
VERNOITPIRCSEDETADDEVORPPA
-ESAELERNOITCUDORP61-91-8HS
AW,E
KALYTREBIL
V.S.O122TIF"61/3KNIRHSTAEHKLB6
V.S.O122TIF"23/3KNIRHSTAEHRAELC5
V.S.O122TIF"01/9KLB,KNIRHSTAEH.AID"4/14
V.S.O1744ETITCOL3
1.S.O500LS3023.TF3,.DLHSGWA62DNOC4ELBAC2
1KTS2-360651KROWERLLEHSROTCENNOC1
61-31-7
61-31-7
61-31-7
A/N
:SETON
.ni3YLETAMIXORPPASDAELROTCENNOCMIRT.1
.YLBMESSAROTCENNOCELBACROF07-260651GNIWARDOTREFER.2
.S-54-86-THPLOOT
PMIRCESU.3
.ERIWDNUORGNOKNIRHSTAEHRAELC23/3ESU.4
.TEEF3=HTGNELLLA
REVO.5
1-526551
).TF3(SDAELGNIYLF/WELBACREGGIRT/REWOPSPM1-
MPS Flying Leads Cable Connections
GND NC

MPS4200 Quick Start Guide
191.30.yyy.xxx
Where yyy is the family code:
090 for MPS4264
095 for MPS4232
Where xxx is the last three digits of the serial number of the
module.
Congure the IP address of the host computer to be compat-
ible with this address. One example would be:
MPS4200: 191.30.95.234
Host Computer: 191.30.95.1
Subnet: 255.255.0.0
Please consult your computer or operang system for steps
on how to congure your computer’s IP address.
Step 5: Access the MPS’s Web Server
The MPS4200 has a single user web server which provides a
simple method for communicaon, conguraon and data
collecon from virtually any host computer.
The web server has been tested with several web browsers
to verify funconality and compability. Those that were
tested are (as of 4/2022):
Mozilla Firefox
Google Chrome
Microso Edge
To connect to the MPS4200’s web server, simply open one of
the supported browsers. In the address bar, enter:
xxx.xxx.xxx.xxx <ENTER>
(where xxx.xxx.xxx.xxx is the IP address of the MPS)
Once connected, the web server’s Scan page will be dis-
played.
Step 6: Scanning
There are mulple variables on this screen that the user may
modify to adjust scan conguraons. Congure a scan rate
(RATE) and select an Engineering Unit (UNITS). Default set-
ngs will be loaded. Then select a format (FORMATTED FOR).
The default selecon is to show scan data to the screen. The
user may also elect to scan to a .CSV, .TXT, or .DAT le.
Once congured, click the CALZ buon in the top right
corner and wait for 10 seconds. Click the SCAN buon to
start data collecon. If the format is set to “Screen”, data will
now be displayed in the bargraph area. For more opons or
detailed informaon on the web server, please see secon 3
in the MPS4200 User Manual.
Example: Setting Static IP address - Windows 10
MPS’s Web Server - Scan Page
MPS’s Web Server - Scanning