Schaefer Waycool WC-1HP-DHL User manual

Portable Evaporative Cooling Fans
Designated Hazardous Location WayCool®
Model WC-1HP-DHL
USER’S MANUAL
Class I: Hazardous location is one in which flammable gases or vapors may be present in the air in sufficient quantities to be explosive or
ignitable.
Class II: Are those areas made hazardous by the presence of combustible dust.
Class III: Are areas where there are easily-ignitable fibers or flyings present, due to the types of materials being handled, stored, or processed.
Division 2: Not normally present in an explosive concentration (but may accidentally exist).
Testing/Certifications Standards: Electrical Equipment for Use in Class I and Class II, Division 2 and Class III Hazardous (Classified) Locations.
[UL 1604, Third Edition, October 6, 1995, Including: Bulletins dated 3/22/95 & 5/17/96]
Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations [CSA C22.2 No. 213-M1987]
Electrical Fans [UL-507, Ninth Edition, 9/24/01 and Fans and Ventilators [CSA C22.2 No. 113-M1989. Sixth Edition]
Certified for Class I
,
Division 2
,
Grou
p
D Class II
,
Grou
p
s F & G & Class III Hazardous
(
Classified
)
Locations
ETL certified for United States
and Canada

2
INTRODUCTION---------------------------------------------------------------------------------------------------------3
Why use evaporative coolers in your work place?---------------------------------------------------- 3
How evaporative cooling works?-------------------------------------------------------------------------- 4
ABOUT THIS MANUAL------------------------------------------------------------------------------------------------ 5
SAFETY INFORMATION---------------------------------------------------------------------------------------------- 6
SAFETY RECOMMENDATIONS----------------------------------------------------------------------------------- 8
WC-1HP-DHL SPECIFICATIONS---------------------------------------------------------------------------------- 10
WC-1HP-DHL UNIT DESCRIPTION------------------------------------------------------------------------------- 11
WATER SUPPLY SYSTEM------------------------------------------------------------------------------------------ 11
COOLING PAD ASSEMBLY----------------------------------------------------------------------------------------- 14
BLOWER AND DUCTWORK-----------------------------------------------------------------------------------------15
CONTROL-----------------------------------------------------------------------------------------------------------------16
OPERATION AND MAINTENANCE-------------------------------------------------------------------------------- 17
Unit Placement and Other Considerations-------------------------------------------------------------- 17
Unpacking and Initial Setup--------------------------------------------------------------------------------- 18
Regular Cleaning---------------------------------------------------------------------------------------------- 19
Normal Startup------------------------------------------------------------------------------------------------- 20
Normal Shutdown----------------------------------------------------------------------------------------------20
TROUBLESHOOTING------------------------------------------------------------------------------------------------- 21
Cooling Pads not Wetting----------------------------------------------------------------------------------- 21
Foaming--------------------------------------------------------------------------------------------------------- 21
Line Clogs or Obstructions---------------------------------------------------------------------------------- 21
Splattering out Front------------------------------------------------------------------------------------------ 22
Leaking out Bottom------------------------------------------------------------------------------------------- 22
General-------------------------------------------------------------------------------------------------------------------- 23
Warranty------------------------------------------------------------------------------------------------------------------- 24
TABLE OF CONTENTS

3
WHY USE EVAPORATIVE COOLERS IN YOUR WORKPLACE?
• The WayCool®evaporative cooler requires little space, has a low initial cost, is
inexpensive and simple to operate and requires minimal scheduled maintenance.
• Due to the design and construction of the cooling pads, cooling efficiency is
normally maintained near optimum throughout the life of the pads, which can easily
last for about two seasons with proper care.
• In many cases, evaporative coolers are a better solution than mechanical
refrigeration systems because they are more economical to operate and maintain
and do not use environmentally sensitive and costly refrigerants.
INTRODUCTION

4
HOW EVAPORATIVE COOLING WORKS
Figure WC-1HP-DHL.02 - Evaporative Cooling Principle
Evaporative cooling is the same process your body uses to cool itself. When you perspire, and air moves
across your skin, a portion of the perspiration (water) evaporates. Evaporation requires heat to change liquid
water-to-water vapor and this heat is taken from your skin, producing the cooling effect.
In an evaporative cooler, the cellulose cooling pads take the place of your skin, water instead of perspiration
wets them and a fan moves the air. The air blows across the cooling pads and evaporates moisture. Heat is
drawn from the pads and the air, dropping the air temperature and producing the cooling effect. The cooled
air is then forced through a building or space and displaces the warm air out building openings, cooling the
surroundings. In addition, air velocity increases the cooling effect as it moves over the skin of people in the
airflow path.
WayCool®evaporative coolers are portable and use the latest technology to provide large volumes of cool
air, efficiently and inexpensively for cooling small to medium size areas. Simply adding more units can
accommodate larger areas. With proper sizing and application, a WayCool®portable evaporative cooler can
lower the effective air temperature by up to 20°. Even in high humidity, the efficiency of the WayCool®
evaporative cooler provides effective cooling.
INTRODUCTION

5
The intent of this manual is to help you in two ways: to provide you with step-by-step instructions for quick and
easy assembly of your product and to serve as a reference for simple maintenance and questions regarding
your product.
Important! Read ALL instructions carefully before starting your WayCool®.
Important! Pay particular attention to all SAFETY information.
All information, illustrations and specifications in this manual are based on the latest product information
available at the time of printing. We reserve the right to make changes at any time without notice.
ABOUT THIS MANUAL

6
Warning and Danger Decals have been placed on the equipment to warn of potentially dangerous situations.
Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged
safety decals immediately.
Using the equipment for purposes other than specified in this manual may cause personal injury and/or damage
to the equipment.
Safety-Alert Symbol
This is a safety-alert symbol. When you see this symbol on your equipment, be alert to the potential
for personal injury. This equipment is designed to be installed and operated as safely as possible…
however, hazards do exist.
Signal words are used in conjunction with the safety-alert symbol to identify the severity of the warning.
CAUTION indicates an imminently hazardous situation, which, if not avoided,
COULD cause damage to your equipment or equipment failure.
WARNING indicates a potentially hazardous situation, which, if not avoided, COULD
result in death or serious injury.
SAFETY INFORMATION

7
ETL LISTED
3019762 CONFORMS TO
UL STD 307
UL STD 1804
CERTIFIED TO
CSA C22.2 STD NO. 113
CAN/CSA C22.2 STD NO. 213
Follow Safety Instructions
Carefully read all safety messages in this manual and on your equipment safety decals. Follow
recommended precautions and safe operating practices.
Keep safety decals in good condition. Replace missing or damaged safety decals.
Decal Descriptions
This diagram shows the proper location of the safety decals as shipped from the factory. Replace
damaged or missing decals. Make sure the decals are easy to see at all times.
START UNIT WARRANTY WAR
Figure WC-1HP-DHL.03 - Decals
START UNIT - WARRANTY -
Turn water pump on 5-10 minutes before running blower VOID IF YOU RUN THE PUMP
to wet evaporative cooling pads. WITHOUT WATER.
SHUT DOWN -
Turn pump off and run only blower until evaporative
cooling pads are dry. This prolongs the life of the pads. CLEANING -
Clean pads a minimum of once every
CAUTION – ALWAYS TURN OFF AT SWITCH AND DIS- two weeks. Remove pads from unit
CONNECT POWER BEFORE REMOVING EVAPORA- and clean with garden hose only -DO
ORATIVE COOLING PADS FOR CLEANING OR INTERNAL NOT use chemicals or high pressure hose.
MAINTENANCE.
A
TTENTION!
The unit is suitable for
outdoor locations, but cannot be
used with an extension cord.
WARNING!
The motor in this unit is equipped
with automatic thermal protection.
The motor can start up or shut
down automatically. Ensure power
is removed before removing
protective grates and pads.
WARNING!
This unit can ONLY be use in the Hazardous Locations listed on this label.
The unit is certified for Not-Normally Hazardous Locations:
Class1, Division 2, Group D
Class 2, Division 2, Groups F & G
Class 3 Locations
As described by the “National Fire Protection Association”
Codes NFPA 597 and NFPA 599
Please review these codes to fully understand permitted applications
and locations prior to use of this product
SAFETY INFORMATION

8
READ AND SAVE THESE INSTRUCTIONS!
• This is an electric device with moving components. There is the possibility of
fire, electric shock, or injury to persons. Ensure all the safety recommendations
are adhered to in order to minimize this risk.
• Disconnect all power and unplug the unit before you inspect, clean or perform
maintenance on the components of the unit.
• Never reach into the unit when it is running; you could become entrapped by
the v-belt or injured by the rotating fan blades.
• Do not service the electrical components unless you are certified to do so.
• The metal frame edges are sharp; don't run your hand along them. Be careful
and wear gloves when you reach under the frame to inspect the PVC pipes and
mesh socks.
• A GFCI (Ground Fault Circuit Interrupter) is required for use with this unit.
• If pads and grates are removed for servicing, they must be replaced prior to
operating unit.
• Unit cannot be used with a solid-state control device.
• An extension cord can not be used with this unit.
• Units can only be used in an environment it has been certified for.
Table of Contents
SAFETY RECOMMENDATIONS

• Height and Width – 33” X 33” wide X 54” high (with casters and directional blower duct)
• Shipping Weight - 265 pounds
• Blower - Double-Inlet Centrifugal
• Motor - 1 HP, 115V, 60 HZ
• Pump - Submersible pump, Vane Type, 280 GPH (Gallons Per Hour)
• Pump Filter - Washable Polyethylene Filter
• Pump Discharge Filter - 480 Micron Stainless Steel
• Reservoir Capacity - 24 Gallons
• Optional Water Supply - Standard ¾" hose connection (garden hose size)
• Housing - High impact ABS plastic w/UV protection
• Evaporation Media - Chemically treated cellulose paper
Figure WC-1HP-DHL-04.Waycool Evaporative Cooler Overview
W
C-1HP-DHL SPECIFICATIONS
A
ctual WC-1HP-DHL
W
ayCool®
V
aries slightly from unit
shown here.

10
The WayCool®evaporative cooler is a completely self-contained, portable unit capable of delivering 40 MPH
velocity of air with a temperature drop of up to 20°. The unit is composed of:
• Level-controlled water supply system
• Cooling pad assembly
• Motor-driven blower and ductwork
• Controls
• Frame and housing
The bottom is made of high impact ABS plastic and holds approximately 24 gallons at normal operating level
(about 5" deep).
A float-operated valve automatically maintains proper water level when the unit is connected to a water
supply.
The bottom rests on, and is fixed to, an aluminum cradle. The bottom, in turn, is secured to the aluminum
frame. Four casters (2 locking, 2 regular) are attached to the underside of the aluminum cradle.
A pump draws water from the bottom and discharges it through the vinyl hose to the PVC pipes located
above the cooling pads. The PVC pipes distribute water onto the top of the cooling pads; saturating them.
Excess water drips back into the bottom through the holes in the cooling pad support channels.
The cellulose cooling pads sit in support channels and are held in place by plastic retaining grates. The
grates also help prevent damage to the cooling pads. Two pad sections fit in each side of the unit (total eight
sections) to totally enclose the unit.
The blower is hung from the top of the frame and powered by a belt driven 1HP electric motor. The blower
draws room air through the cooling pads where it picks up moisture and cools by evaporation. The blower
then discharges the cooled air.
Note: It is important the cooled space has sufficient air openings so the warmer air can flow out and
be replaced by the cooled air. A closed-in space or high humidity will reduce the cooling effect. See
Unit Placement and Other Considerations in the “Operations and Maintenance” section of this
manual.
A screen covers the discharge duct to prevent foreign objects from entering the blower. A threaded rod
screws through a threaded brace above the screen to hold the blower duct in position. A plastic knob
secures the blower duct to the rod. The blower duct is made of a tough, durable plastic and can be manually
rotated 360 degrees to provide cool air in any direction without moving the unit.
Note: Water weighs about eight pounds per gallon, so when the unit is full, it weighs over 375
pounds. During setup and before startup, place the unit in the desired location and then fill the
bottom. Do not attempt to lift the unit once it is filled and be careful to avoid spills when moving it;
even over smooth ground. Do not try to push it over rough or soft ground as you can overstress the
wheels and frame and cause structural and component damage, which is not covered by warranty.
W
C-1HP-DHL UNIT DESCRIPTION

11
The bottom can be supplied continuously with an ordinary garden hose by attaching the supplied hose adapter
(see Figure WC-1HP-DHL.08) to the fill connection, or it can be filled manually.
With a continuous water supply connected, the float valve in the bottom (like the one in your toilet tank) rises
and falls with the water level. A linkage attaches the float to the shutoff valve in the fill connection. As the water
level rises to normal operating level (about 5" deep), the float valve shuts off the water supply. When the water
level drops, the float valve reopens to maintain a normal operating level.
After unplugging the unit, the bottom can also be manually filled with a hose or bucket; if a hose connection is
impractical. Simply remove any of the plastic retaining grates and one of the cooling pad sections and place
the hose, or pour the water, directly into the bottom. When you fill the bottom manually it can be filled to a
higher level, but make sure someone monitors the filling operation to avoid overfilling and flooding.
Note: Water damage due to overfilling is not covered by the warranty.
Note: When you run the unit and manually fill it, check the water level frequently so it does not run dry.
Operating the pump without water will damage it or reduce its service life. This is not covered by the
warranty. The cooling effect also stops if the pads are dry.
Note: Pads and grates must be replaced before operating unit.
W
ATER SUPPLY SYSTEM
A
ctual WC-1HP-
DHL WayCool®
V
aries slightly from
unit shown here.
Figure WC-1HP-DHL.05 – Water Supply System

12
A drain in the bottom allows you to drain the unit for cleaning and maintenance. A drain cap on the underside
of the aluminum tray covers the drain during operation. Make sure the cap is in place before you fill the bottom.
The drain cap should be finger-tightened only.
The pump is attached to a bracket which in turn is fixed to the blower housing. The bracket holds the pump in
its proper position on top of the foam filter and slightly above the bottom; allowing sufficient space for water to
enter the pump suction.
The pump can be easily removed and replaced with the services of a qualified electrician.
Figure WC-1HP-DHL.06 – Pump
A small plastic screen covers the pump inlet to prevent foreign matter from entering and damaging the pump
impeller. The screen snaps in place and can be easily
removed for inspection or cleaning.
Water Supply System
The pump sits on a foam filter; somewhat like a sponge. The filter traps dirt that could enter the water
distribution system and build up on the cooling pads; reducing their effectiveness. Dirt could also accumulate in
the PVC pipes and plug up the spray holes.
The pump discharges through a fine, washable screen filter which decreases the contamination of the cooling
pads and water system. The discharge filter casing is a clear plastic so dirt buildup on the internal screen is
easily visible. As dirt builds up, water flow to the cooling pads is reduced and performance decreases. The
clear filter housing is threaded and screws into the filter body for easy removal to access the screen.
Note: A dirty water supply will quickly reduce the unit's performance and the unit will require more
frequent cleaning to maintain cooling effectiveness. Always try to use a filtered, treated water supply.
W
ATER SUPPLY SYSTEM
Plastic Screen
Pum
p
Im
p
eller

13
A clear vinyl hose connects the pump to the filter. From the filter, a "T" connector supplies two lines that run
along the bottom and up opposite frame corners to supply the PVC pipe with water. Each vinyl hose
connects to two PVC pipes, which run horizontally along the top of the frame above the cooling pads.
Water Supply System
The PVC pipes have a series of holes that run the full length of the pipe. Each PVC pipe is covered with a
plastic mesh sock which helps break up the water as it leaves the spray holes. This gives a more even
water distribution across the cooling pad and reduces splashing. The holes direct the water inward at a 90°
angle to continuously saturate the cooling pads from the top down. Excess water drains back to the bottom
through drainage holes in the bottom support channels which support the cooling pads.
Note: Water cleanliness has a major effect on the cooler's performance. Use a clean water supply
and consider a water softener if your water is hard. Dissolved solids in hard water deposit on the
cooling pad surfaces and reduce the airflow through the unit and therefore the amount of
evaporation.
W
ATER SUPPLY SYSTEM

14
The cooling pads are critical for proper, efficient cooler operation. They are made of laminated cellulose
(paper) fibers and arranged to give a large surface area for evaporation and to provide a rigid structure. The
shape of the cells allows high velocity airflow through the pad at a minimum pressure drop. At the same time,
the air passages between the cells force the incoming air to impinge on the wet cell surfaces and maximize
evaporation.
Note: The WayCool® evaporative cooler also acts as an air filter and removes dust and other particles
from the air. This dirt collects on the cooling pads and lowers cooler efficiency. The pads should be
cleaned at least weekly and more frequently in dusty conditions. See Regular Cleaning under
“Operation & Maintenance”.
The pump supplies a continuous flow of water over the pads causing a “sheet flow” which constantly replaces
the water lost to evaporation and keeps the pads saturated.
One cubic foot of the cooling pad material holds about a gallon of water during operation. One cubic meter
holds about 100 liters of water.
Note: The cooling pads are relatively strong but are subject to crushing, especially when wet. Always
run the unit with the plastic retaining grates in place and handle them carefully when you clean them.
Crushed cells reduce the total airflow through the unit and therefore lowers it’s cooling capacity.
The cooling pad sections, two sections for each side (eight sections total), sit in metal channels at the top and
bottom of the unit. The channels hold the cooling pads in position and form four sidewalls to completely
enclose the unit.
The top channels house the PVC pipe, which run horizontally along the channel directly above the cooling
pads. The bottom channels have a series of holes drilled through them to allow excess water flowing down
the cooling pads to return to the bottom.
The plastic retaining grates fit in front of the cooling pads and sit in the same channels as the pads; holding
them in place and protecting them from accidental damage. The plastic grates and cooling pads are easily
removed by placing a flat blade under the bottom and lifting upwards, then outwards. Once one pad is
removed, the others can be lifted up and out by hand without using a blade.
Note: Do not remove or handle the cooling pads when they are wet, as they damage easily. Run the
blower without the pump until pads are dry. With normal care, the pads should last at least two
seasons. Abuse or mishandling will reduce their effectiveness and shorten their life.
Cooling Pad Assembly
COOLING PAD ASSEMBLY

15
Figure WC-1HP-DHL.07 - Fan Blower
The WayCool®WC-1HP-DHL uses a belt-driven, 1 HP electric motor to drive a centrifugal blower. The blower
draws room air through the cooling pads and discharges the cooler air through the blower duct, displacing the
warmer air with cooler air and decreasing the temperature.
The blower is secured to the top of the frame and hangs upside down to direct the air out the top of the unit.
Brackets on each side of the blower casing secure the blower to the frame and hold it in position.
The electric motor is bolted to a metal bracket on the blower casing. A V-belt connects the pulley on the motor
shaft to the larger pulley on the blower shaft. Both shafts have sealed roller bearings, which do not require
lubrication.
Blower and Ductwork
A belt tensioner is connected to a bracket on the motor. A rubber foot at one end rests against the blower
casing. When the locking nut is backed off, the bolt can be turned in to tighten the V-belt or backed out to
loosen or remove the V-belt.
Note: Do not over tighten the V-belt as you can prematurely wear out the bearings.
The power cord runs down the frame leg that has the control switch on the outside. It exits the frame leg at the
bottom and has a male plug that must be plugged into a suitable hazardous location receptacle. The cord is
approximately fifteen feet long.
Note: The WC-1HP-DHL unit requires 120 volts and 20 amps of power. This is normally available on
most circuits. However, if you are running a number of other items on the same circuit, you may trip
the breaker.
Blower and
D
BLOWER AND DUCTWOR
K
A
ctual WC-1HP-DHL
W
ayCool® varies
slightly from unit shown
here.

16
Figure WC-1HP-DHL.08 - WayCool Control Switch
Both the manual Motor starter switch and the Pump switch function as ON/OFF only. The unit can run with
pump only ON, fan (motor) only ON or both ON.
CONTROLS
Manual Motor starter switch
ON
/
OFF
–
sin
g
le s
p
eed
Pum
p
Selector Switch

17
UNIT PLACEMENT AND OTHER CONSIDERATIONS
Figure WC-1HP-DHL.09 Typical WayCool® Unit Arrangement
The WayCool®unit(s) should be placed at one end of the building and an appropriate exhaust fan should be at
the opposite end to pull the cool air from the WayCool® unit and discharge the warm air out of the building.
Try to get all the air flowing in the same direction. Do not direct other fans against the WayCool®unit. It will
counter the WayCool®'s airflow and stop the cooling effect.
Obstructing the airflow from the WayCool®unit severely reduces the cooling effect.
Avoid using ceiling fans as they disrupt the airflow from the WayCool®unit.
Use as many exhaust fans as possible to create a natural draft through the building. This will enhance the
WayCool's ® performance.
OPERATION & MAINTENANCE

18
Operation and Maintenance
UNPACKING AND INITIAL SETUP
The WayCool®WC-1HP-DHL Evaporative Cooler is shipped upright in a corrugated container. The
WayCool®WC-1HP-DHL is fully assembled and ready for service except for thoroughly cleaning
manufacturing dust from the cooling pads before running it for the first time.
CAUTION: Be careful when you move the unit while it is in the shipping container and when moving
it around with the container removed. Avoid jarring or dropping the unit to prevent damage to the
bottom.
1. With the unit in the upright position as marked on the container, use a sharp knife or scissors to cut
the straps that wrap the shipping container.
Note: Do not discard the container until you have thoroughly inspected the unit.
2. Remove the shipping container.
3. Ensure the switch is OFF and the unit is unplugged.
4. Remove the grate bracket and the plastic retaining grates from all four sides of the unit. Use your
fingers to lift each upward, then outward from the bottom.
5. Remove the cooling pads from all four sides of the unit.
Place a putty knife or large, flat-bladed screwdriver
under the pad to lift it up, then outward. With one pad
out, the rest can be easily removed by placing one hand
on the pad's inside, your other hand on the outside and
lifting the pad up and out from the bottom (see figure
WC-1HP-DHL.10).
Figure WC-1HP-DHL.10
6. Inspect the entire unit for shipping damage.
7. Ensure the fan belt is attached to the motor and blower pulleys and that the belt tension is correct.
To ensure it is correct, press your finger on the belt about halfway between each pulley. It should
have about a half inch of play. Too loose and the v-belt will slap around while running. Too tight will
cause the pulley bearings to wear and fail prematurely.
8. Look for cracks in the bottom near the frame legs. This is also an indication of rough handling.
OPERATION & MAINTENANCE
A
ctual WC-1HP-
DHL WayCool®
v
aries slightly from
unit shown here.

19
9. Ensure the frame legs are straight and in alignment, and that the blower is sitting level and in proper
position.
Maintenance
Note: If you notice any damage to your unit, immediately contact the dealer where you purchased it.
10. Clean thoroughly all eight cooling pad sections using a garden hose.
Note: Do not use cleaning fluids or other chemicals to clean the pads or it can cause foaming during
operation. Use only clean water.
11. Remove the drain cap from the underside of the bottom and rinse with a hose to flush any
manufacturing dust, etc. from the unit. Replace the drain cap.
12. Replace the pads, the protective retaining grates, and the grate brackets.
13. Proceed to “Normal Setup”.
REGULAR CLEANING
The frequency with which the WayCool®is cleaned will depend on the environment in which it is used. The
more dirty the environment the more often it will need cleaning. In most cases the WayCool®will need to be
cleaned weekly.
Caution: The pads should be dry before you handle them, as they are stronger when dry than when
they are wet and less susceptible to damage. If they are wet, run the unit in the HIGH VENT position
until they are dry. After cleaning, let the pads air dry before you replace them.
1. Turn the switch to OFF and unplug the unit.
2. Remove the grate brackets and the plastic retaining grates and check the pads for cleanliness. If they
are dirty, remove and clean with a garden hose. If they are not dirty you will still need to remove the
cooling pads to clean the inside of the unit. Dirty cooling pads reduce the unit's effectiveness.
3. Use a garden hose to rinse out the bottom and the inside of the unit. The dirt that accumulates is
removed from the air during operation, as the Waycool unit also acts as an air filter.
4. Remove the drain cap from the underside of the unit and let the unit drain completely. Rinse out any
remaining dirt.
5. Replace the drain cap (finger tighten only).
6. Remove the pump discharge filter by unscrewing the top, removing the screen and rinsing it with a
hose or under a tap. Replace the filter screen and screw the top back on.
7. Remove the pump filter from underneath the pump. Wash thoroughly with a hose. Compress filter
and place back under the pump.
8. Replace the cooling pads once they are dry and reinstall the plastic retaining grates and the grate
brackets.
Note: With proper use and regular cleaning, the cooling pads will last about two seasons. If you
handle them wet and are abusive, however, they will be easily damaged.
OPERATION & MAINTENANCE

20
NORMAL STARTUP
1. Place the unit in the position where it will be run. Do not attempt to lift or move the unit once it is filled.
Damage to the unit or a large spill may occur.
Note: When you decide where to place the unit, make sure there are no obstructions in the way that
will disrupt or block the airflow. Make sure the unit is level at all times. Keep the unit at least three
feet away from walls or other obstructions that will interfere with airflow into the unit.
2. Check to ensure the drain cap is in place and secure.
3. Connect the garden hose to the brass hose adapter. Check that there is a washer in the hose
connection's female end.
4. Open the water supply valve and check that water enters the bottom through the float valve by
removing one cooling pad on the side with the water connection. Allow the unit to fill and check that
the float valve completely shuts off the water.
5. If you are manually filling, remove one or more cooling pads and fill the bottom with a bucket or hose.
6. Visually monitor the filling operation to avoid overflowing and causing spill damage.
7. Plug the unit into an outlet.
8. Adjust the blower duct to discharge the cool air in the desired direction and tighten the knob on the end
of the threaded rod.
9. Turn the pump switch to the on position and let it run for 5 - 10 minutes to saturate the cooling pads.
Check that the pads are saturated completely and there are no dry spots.
CAUTION: Do not run the pump without water in the bottom or you will damage the pump. Running the
pump dry will void the warranty on the pump.
10. Turn the motor switch to the start position to begin normal cooling operation.
NORMAL SHUTDOWN
1. Turn the pump switch to the OFF position.
2. Leave the motor switch in the START position and let the unit run until the cooling pads are dry. This
will maximize the life of the pads.
3. Turn the motor switch to the OFF position. Unplug the unit if you are going to clean the pads or inspect
the components.
4. Shut off the water supply.
5. Drain the bottom if you are going to clean it or store it.
6. If the unit will be stored for the season, ensure the cooling pads are completely dry, and then remove
them. Wrap them in plastic bags or store them in a clean place where they will not be damaged or get
dirty. The unit should be cleaned thoroughly before storing.
OPERATION & MAINTENANCE