Schulthess Spirit Eco WA 4750 User manual

1
Safety instructions
– The washing machine is heavy - take care when lifting.
– Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed
to frost or outdoors.
– The washing machine could be damaged. Do not lift the appliance by protruding
components (e.g. the washing machine door).
– In addition to the instructions provided in this document, special regulations from the
relevant water and electric utility companies may apply.
– If in doubt, have a technician connect the appliance.
– Lay hoses and cables in such a way that there is no risk of tripping.
Installation surface
– The machine must be stable so that it does not move around.
– The installation surface must be firm and level.
– Soft floors/floor coverings are not suitable.
Installation on a pedestal
– The feet of the washing machine must be secured with holding brackets*.
* order no. WMZ2200
Installation on a wood joist floor
– If possible, place the washing machine in a corner.
– Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
– The feet of the washing machine must be secured with holding brackets*.
* order no. see above
Installing the appliance
Install the appliance before connecting it to the power supply.
Installation in a kitchenette (underneath the worktop or fitted in a cabinet)
– Recess width of 60 cm required.
– Only install the washing machine underneath a continuous worktop that is securely
connected to adjacent cabinets.
Installation underneath the worktop
Risk of electric shock.
– Instead of the appliance covering plate, you must have a metal cover * fitted by an expert.
* order no. WMZ2420
– Recess width of 60 cm required.
2
Scope of delivery
Also required, depending on the connection:
– 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon
apage 4; water connection.
Useful tools
– Spirit level for installation.
– Spanner with
WAF13: for loosening the transport safety devices aPage 3 and
WAF17: for aligning the appliance feet aPage 5.
Hose and cable lengths
Left-hand connection or Right-hand connection
Available from specialist dealers/the after-sales service:
– Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m).
order no. WMZ2380
Mains cable
Water outlet
Water inlet
Covers
Elbow
for fixing the drainage
hose in place
~145 cm ~100 cm
~90 cm
~140 cm
~145 cm
min. 60 cm
~90 cm
max. 100 cm
Moisture inside the drum is
due to final testing.
a
ää

aaa
3
Removing the transport braces
– Before using the appliance for the first time, make sure that you
completely remove transport braces and keep them for subsequent
transportation.
– If you need to transport the appliance at a later date, always re-affix the
transport braces to prevent damage to the machine apage 6.
– Store the screw and sleeve screwed together.
1. Take the hoses and elbow out of the holders, depending on model.
2. Loosen the bolts ....
... until they move freely in the sleeves.
3. Completely remove all 4 transportation protection and take the main cable
out of the holder.
4. Insert covers.
4
Water connection
–Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leaks or water damage, observe the instructions in this
section.
–Caution: only operate the washing machine using cold drinking water.
– Do not connect to the mixer tap of an unpressurised hot-water boiler.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have a technician connect the appliance.
Water inlet
Water inlet hose:
Caution: do not bend, squash, modify or cut through
(otherwise its strength is no longer guaranteed).
Optimum water pressure in the supply network: 100ä1,000 kPa (1ä10 bar)
– When the tap is on, the water flow is at least 8 l/min.
– If the water pressure is higher than this, a pressure reducing valve must be installed.
1. Connect the water inlet hose to the tap.
Caution: only tighten the screw connections by hand.
2. Open the water tap carefully, checking the leak
tightness of the connection points.
Caution:the screw connection is under mains water
pressure.
Water outlet
Water outlet hose:
Caution: do not bend or pull lengthways.
Height difference between the installation surface and the drain:
min. 60 cm - max. 100 cm
Outlet in a sink
Caution: secure the drain hose from slipping out.
Caution: the plug must not block drainage from the sink. During
pumping, check whether the water is draining away quickly enough.
The end of the drain hose must not be immersed in the water pumped
out. This risks water being sucked back into the washing machine.
Drainage into a siphon:
Caution: the connection point must be secured with a hose clamp,
Ø 24-40 mm (exclusive dealers).
max.
90°
max.
90°
min.
10 mm
3/4”

5
1010 / 9000591188 *591188*
Alignment
Intense noise formation, vibrations and “wandering” may be the result of incorrect
alignment.
Aligning the washing machine with a spirit level
1. Loosen the lock nut using a wrench, by turning it in a clockwise direction.
2. Change the height by turning the appliance feet.
Caution: all four appliance feet must be firmly on the ground.
The washing machine must not wobble.
Check the alignment of the washing machine with a spirit level and adjust
if necessary.
3. Tighten the lock nut against the housing.
In doing so, hold the foot tight and do not adjust its height.
Caution: the lock nuts on all four appliance feet must be screwed tightly
against the housing.
Electrical connection
ʑThe washing machine must only be connected to an alternating current via a
properly installed earthed socket.
ʑThe power supply and voltage indicated on the washing machine (rating plate)
must be the same.
ʑThe connected load and fuse required are specified on the rating plate.
ʑMake sure that:
– the mains plug fits the socket,
– the cable cross-section is adequate,
– the earthing system is properly installed.
ʑ(If this is necessary), the mains cable may only be replaced by a qualified
electrician.
Replacement mains cables are available from the after-sales service.
ʑDo not use multiple plugs/couplings or extension cables.
ʑIf a residual current circuit breaker is used, only use a type which displays this
symbol: ‚.
Only this symbol guarantees compliance with the currently applicable regulations.
ʑDo not plug in or unplug the mains plug with wet hands.
Pull the appliance plug out of the socket at the plug only, not by the cable.
6
Transportation, e.g. when moving home
Before transporting the washing machine:
1. Turn off the tap.
2. Release the water pressure in the inlet hose aOperating instructions; Maintenance - filter
in water inlet.
3. Drain residual water aOperating instructions; Maintenance - drain pump.
4. Disconnect the washing machine from the power supply.
5. Dismantle the hoses.
Preparing and installing transport braces:
1. Remove the covers.
2. Insert all 4 transportation protection devices and clamp the mains cable
to the holders. Tighten the bolts.
After transportation, the transport braces must be removed apage 3.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour
1 litre of water into compartment II and start the <Drain programme.
Technical specifications
ʑDimensions (width x depth x height) 60 x 59 x 84.2 cm
ʑWeight 72 kg
ʑMains connection Nominal voltage 220-240 V, 50 Hz
Nominal current 10 A
Nominal power 2300 W
ʑWater pressure 100ä1000 kPa (1ä10 bar)
ʑTest programmes According to currently valid IEC 60 456
1.
2.
ʑaʑʑʑ>ʑʑ
ʋʋʋʋʋʋʋʋʋʋʋʋʋ

ʑʑʑʑʑʑʑʑaaa<ʑʑʑʑääʑ1.
2.
7
Customer service
ʑBefore you call the after-sales service, please make sure that you cannot remedy the fault
yourself aOperating instructions; What to do if...
ʑIf you require advice, even during the warranty period, you will incur costs for the call-out
of a technician.
ʑThis guarantee does not cover damages resulting from improper use as well as from choked
filters or foreign bodies.
ʑIs a fault cannot be rectified or a repair is required:
– Set programme selector to >Off and pull out the mains plug.
– Turn off the tap and call customer service.
ʑCentral customer service numbers for Switzerland:
Schulthess Maschinen AG
Tel. [phone] / FAX [phone]
Merker AG
Tel. [phone] / FAX [phone]
ʑPlease supply the after-sales service with the product number and model name of your
appliance.
Guarantee subscription
After the end of the normal 2 years guarantee period, this can be extended if required with a
guarantee subscription. We will be happy to send you the relevant documents. Please see
also the enclosed guarantee and customer services booklet.
Washing machine
Contents Page
ʋSafety instructions . . . . . . . . . . . . . . . . . . . . 1
ʋInstallation surface. . . . . . . . . . . . . . . . . . . . 1
ʋInstalling the appliance . . . . . . . . . . . . . . . . 1
ʋScope of delivery. . . . . . . . . . . . . . . . . . . . . 2
ʋHose and cable lengths . . . . . . . . . . . . . . . 2
ʋRemoving the transport braces . . . . . . . . . . 3
ʋWater connection . . . . . . . . . . . . . . . . . . . . 4
ʋAlignment . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋElectrical connection . . . . . . . . . . . . . . . . . . 5
ʋTransportation, e.g. when moving home . . . 6
ʋTechnical specifications. . . . . . . . . . . . . . . . 6
ʋCustomer service . . . . . . . . . . . . . . . . . . . . 7
ʋGuarantee subscription . . . . . . . . . . . . . . . . 7
Installation
instructions
Read these instructions before switching on the washing machine.
Also observe the separate Instruction manual.
Keep all documents for use in the future or for the subsequent owner.
en