Scion-Tech SC08.CTL100H User manual

SC08.CTL100H
AV over IP
Network Controller
User Manual
Version 4.0
Scion Tech Limited
Unit 10, Thatcham Business Village, Colthrop Way,
Thatcham, Berkshire, RG19 4LW, United Kingdom
www.scion-tech.co.uk
Tel: [phone] www.scion-tech.co.uk [email protected]
User ManualSC08.CTL100HScion Tech

Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before connecting, operating
or adjusting this product. Please keep this manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, elec-
tric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect
and extend the life of your equipment.
Table of Contents
Tel: [phone] www.scion-tech.co.uk [email protected]
User ManualSC08.CTL100HScion Tech
1.0 Introduction......................................................................................................................... 1
2.0 Features............................................................................................................................... 1
3.0 Package Contents................................................................................................................ 1
4.0 Specifications...................................................................................................................... 1
5.0 Operation, Controls and Functions...................................................................................... 2
5.1 Front Panel................................................................................................................. 2
5.2 Rear Panel................................................................................................................... 2
5.3 Infrared Pin Connections............................................................................................ 3
6.0 Web GUI............................................................................................................................. 3
6.1 Preparation.................................................................................................................. 3
6.2 Network Settings - Mode 1, Automatically managed by controller........................... 5
6.3 Network Settings - Mode 2, DHCP............................................................................ 8
6.4 Network Settings - Static IP....................................................................................... 9
7.0 System Control.................................................................................................................... 11
7.1 Preview....................................................................................................................... 11
7.2 Matrix Control............................................................................................................ 12
7.3 Project......................................................................................................................... 13
7.4 Encoders..................................................................................................................... 14
7.5 Decoders..................................................................................................................... 16
7.6 Locked Signal Routing............................................................................................... 18
7.7 Video Wall Management............................................................................................ 18
7.8 Users........................................................................................................................... 22
7.9 Controller Settings...................................................................................................... 22
7.10 Firmware Update........................................................................................................ 23
7.11 Password..................................................................................................................... 23
8.0 Maintenance and Warranty.................................................................................................. 24

Page 1
Tel: [phone] www.scion-tech.co.uk [email protected]
1.0 Introduction
This AV over IP Controller is used to control and manage SC08.MX200/600 Encoders and Decoders. Dual
LAN ports provide network isolation of Control and Multicast video distribution. Built-in Web GUI, TCP and
RS-232 control are supported. The controller has POE and wide band 12V IR signal receiving.
2.0 Features
●Easy to create, control and manage the system
●Supports Auto, DHCP and Manual IP configurations
●HTTPS, SSH, SFTP security compatible
●Built-in Web GUI control interface, supporting Drag & Drop operations
●Video image preview
●Dual network ports for video and control to isolate controls and multicast network.
●Support LAN/RS-232 port control and third-party central control
●Support IR signal receiving (3.5mm audio jack, 12V level)
●4 channel GPIO control ports (5V/12V optional level)
●Multiple circuit protection, lightning protection and ESD design
3.0 Package Contents
1. 1 Video over IP Controller
2. 1 20kHz-60kHz 12V IR Receiver Cable (1.5 meters)
3. 1 3-pin 3.81mm Phoenix Connector (Male)
4. 1 6-pin 3.81mm Phoenix Connector (Male)
5. 2 Mounting Ears
6. 4 Machine Screws (M3*6)
7. 1 12V/1A Locking Power Adaptor
8. 1 User Manual
4.0 Specification
Control Ports
Ethernet (Control)
Ethernet (Multicast) with PoE
Infrared
Digital I/O
RS232
ESD Protection Human Body Model | +/-8kV (air gap discharge) and +/-4kV
(contact discharge)
Housing Metal Enclosure
Colour Black
Dimensions (W) 204 x (D) 98 x (H) 21mm
Weight 509g
Power Supply Input: AC 100 ~ 240V 50/60Hz, Output DC 12V/1A
Power Consumption 4.5 watt
Operating Temperature 32 to 104°F / 0 to 40°C
Storage Temperature -4 to 140°F / -20 to 60°C
Relative Humidity 20 to 90% RH (no condensation)
User ManualSC08.CTL100HScion Tech

Page 2
Tel: [phone] www.scion-tech.co.uk [email protected]
5.0 Operation, Controls and Functions
5.1 Front Panel
Reset
Power
1 2
Status
3
1. Reset Button - Press and hold for approximately 10 seconds until the status LED starts to
flash, the controller will automatically reset.
2. Power LED - Illuminates red when power in applied.
3. Status LED - Flashes amber during initialisation and turns solid green when the unit is con-
nected to the control LAN.
4. Firmware update.
5.2 Rear Panel
1. 12 Volt Power Jack.
2. 1G Ethernet for multicast video with PoE.
3. 1G Ethernet for system control.
4. Normal: Use for RS232 Control. MCU: Use for MCU Upgrade.
5. RS232 communication port.
6. I/O Connections - 4 channel I/O level outputs, ground and 12 Volts.
7. I/O Level Switch between +5 and +12 Volt
8. IR In - 12V infrared input port.
1 2 345678
User ManualSC08.CTL100HScion Tech
Video LAN (PoE)
TX GND RX
RS232
DC 12V Control LAN
IO1
IO2 IO3
IO4 GND
Volt Out
5 Volt 12 Volt
I/O Level
IR In
Update
4
Normal
MCU

5.3 IR Pin Connections
Page 3
Tel: [phone] www.scion-tech.co.uk [email protected]
6.0 Web GUI
6.1 Preparation
The controllers Web GUI gives you complete control of encoders and decoders within your LAN/Project.
Step 1: Enter controllers URL or IP address in to your Web Browser address bar.
URL: http://controller.local
Or
IP Address: 192.168.0.225
Subnet: 255.255.0.0
Enter the username (admin) and password (1234).
For first time setup you need to create a project as shown below.
Welcome to the AV over IP setup guide. It leads you to create the
system easily by following steps.
You can click the “close” button to load an existing project in web
page directly.
Close Next
User ManualSC08.CTL100HScion Tech

Stage 2: Click the “close” button to load an existing project directly in to the web page or click the “next” but-
ton to create a new project.
Page 4
Tel: [phone] www.scion-tech.co.uk [email protected]
To setup AV over IP system, you need to set the IP management mode of the video LAN domain. The IP
management modes are:
●Automatically managed by the controller box.
This is the mode as factory default. The IP address assignments to controller box video LAN, encoders
and decoders will be managed by the controller box firmware automatically. In this mode there is no need
to add router in the system on video LAN domain.
○DHCP Mode
This is the mode for system in which there is a DHCP router on video LAN domain to assign IP addresses
for controller box video LAN, Encoders and Decoders. The router acts as a DHCP server . It’s recom-
mended to set the net mask of router to 255.255.0.0.
○Static IP Mode by Manual setting
This is the mode for system in case IP address resources can be assigned manually for controller box vid-
eo LAN, Encoders and Decoders.
Reminders as below.
a. The network settings of controller box video LAN, Encoders and Decoders must be on the same subnet.
b. It’s recommended to set net mask of controller box video LAN, Encoders and Decoders to 255.255.0.0.
Back Next
User ManualSC08.CTL100HScion Tech
Notes:
1. Currently only mode (1) is available, modes 2 & 3 will be available soon.
2. Default setting for LAN Control Port is DHCP.
3. If there is no DHCP server in your LAN, you can access the controller using (IP Address
192.168.0.225 and subnet 255.255.0.0).

Page 5
Tel: [phone] www.scion-tech.co.uk [email protected]
6.2 Mode 1: Automatically managed by the controller box.
Click the “Next” button and wait for the controller to complete a search
Now you can select to automatically add all discovered Encoders and Decoders to the project or just them in the
web page where you can add them manually.
●Automatically managed by the controller box.
○List all discovered Encoders and Decoders
Back Scan
User ManualSC08.CTL100HScion Tech
Video LAN (PoE)
TX GND RX
RS232
DC 12V Control LAN
IO1
IO2 IO3 IO4 GND
Volt Out
5 Volt 12 Volt
I/O Level
IR Out
TX GND RX
RS232
IR In
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
AV over IP Controller
1G Ethernet Switch
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
Decoder
Decoder
Decoder
Decoder Video Wall
PC
Encoder
Encoder
Encoder

Page 6
Tel: [phone] www.scion-tech.co.uk [email protected]
If you select “Automatically add Encoders and Decoders to project” and click the “Scan” button to enter the
project page. All discovered devices will be listed in the current devices page.
Click “Stop Scan & Auto Assign” to stop search.
If you select “List all discovered Encoders and Decoders”, and click the “Scan” button to enter the Project
page. All the connected devices will be listed in the Unassigned Devices list.
User ManualSC08.CTL100HScion Tech
AVoIP Project
Current Devices Save ProjectDisplay ID Clear Project
Encoders
ID
1
2
3
4
Name
Encoder 001
Encoder 002
Encoder 003
Encoder 004
IP Address
169.254.3.6
169.254.3.1
169.254.3.7
169.254.3.4
Status
Offline
Offline
Offline
Offline
Encoders
ID
1
2
3
4
Name
Decoder 001
Decoder 002
Decoder 003
Decoder 004
IP Address
169.254.6.8
169.254.6.5
169.254.6.2
169.254.6.6
Status
Offline
Offline
Offline
Online
Unassigned Devices
Unassigned Encoders Unassigned Decoders
Stop Scan & Auto Assign Scan
AVoIP
Project
Unassigned Devices
Unassigned Encoders Unassigned Decoders
Configuration & Scan Stop Scan
IP Addresses
169.254.3.1
169.254.3.6
169.254.3.4
169.254.3.7
MAC Addresses
6C:DF:FB:00:00:94
6C:DF:FB:00:03:71
6C:DF:FB:00:00:91
6C:DF:FB:00:03:70
Add All
Edit Add
Edit Add
Edit Add
Edit Add
IP Addresses
169.254.6.8
169.254.6.5
169.254.6.2
169.254.6.6
MAC Addresses
6C:DF:FB:00:00:A2
6C:DF:FB:00:03:A4
6C:DF:FB:00:00:A3
6C:DF:FB:00:03:A0
Add All
Edit Add
Edit Add
Edit Add
Edit Add

Page 7
Tel: [phone] www.scion-tech.co.uk [email protected]
Click “Stop Scan” to stop search. Then the “Add All” buttons and “Add” buttons behind Unassigned Encoders
and Unassigned Decoders in the figure below will become operable.
At this time, you can click the “Add” button behind each unregistered Encoder or Decoder to add the device to
the project one by one, or click the “Add All” button to add all Encoders or Decoders to the project.
Encoders and Decoders that have been added to the project will appear in the Current Devices list, as shown in
the figure below.
User ManualSC08.CTL100HScion Tech
AVoIP Project
Unassigned Devices
Unassigned Encoders Unassigned Decoders
Configuration & Scan Stop Scan
IP Addresses
169.254.3.1
169.254.3.6
169.254.3.4
169.254.3.7
MAC Addresses
6C:DF:FB:00:00:94
6C:DF:FB:00:03:71
6C:DF:FB:00:00:91
6C:DF:FB:00:03:70
Add All
Edit Add
Edit Add
Edit Add
Edit Add
IP Addresses
169.254.6.8
169.254.6.5
169.254.6.2
169.254.6.6
MAC Addresses
6C:DF:FB:00:00:A2
6C:DF:FB:00:03:A4
6C:DF:FB:00:00:A3
6C:DF:FB:00:03:A0
Add All
Edit Add
Edit Add
Edit Add
Edit Add
AVoIP Project
Current Devices Save ProjectDisplay ID Clear Project
Encoders
ID
1
2
3
4
Name
Encoder 001
Encoder 002
Encoder 003
Encoder 004
IP Address
169.254.3.6
169.254.3.1
169.254.3.7
169.254.3.4
Status
Offline
Offline
Offline
Offline
Encoders
ID
1
2
3
4
Name
Decoder 001
Decoder 002
Decoder 003
Decoder 004
IP Address
169.254.6.8
169.254.6.5
169.254.6.2
169.254.6.6
Status
Offline
Offline
Offline
Online
Unassigned Devices
Unassigned Encoders Unassigned Decoders
Configuration & Scan Scan

Page 8
Tel: [phone] www.scion-tech.co.uk [email protected]
6.3 Mode 2: DHCP Mode - Please connect all devices according to the diagram below.
To setup AV over IP system, you need to set the IP management mode of the video LAN domain. The IP management modes are:
○Automatically managed by the controller box.
This is the mode as factory default. The IP address assignments to controller box video LAN, encoders and decoders will be man-
aged by the controller box firmware automatically. In this mode there is no need to add router in the system on video LAN domain.
●DHCP Mode
This is the mode for system in which there is a DHCP router on video LAN domain to assign IP addresses for controller box video
LAN, Encoders and Decoders. The router acts as a DHCP server . It’s recommended to set the net mask of router to 255.255.0.0.
○Static IP Mode by Manual setting
This is the mode for system in case IP address resources can be assigned manually for controller box video LAN, Encoders and De-
coders.
Reminders as below.
a. The network settings of controller box video LAN, Encoders and Decoders must be on the same subnet.
b. It’s recommended to set net mask of controller box video LAN, Encoders and Decoders to 255.255.0.0.
Back Next
Select “DHCP” Mode on the interface as shown below, then follow the steps is “Mode 1”.
User ManualSC08.CTL100HScion Tech
Video LAN (PoE)
DC 12V Control LAN
IO1
IO2 IO3 IO4 GND
Volt Out
5 Volt 12 Volt
I/O Level
IR Out
TX GND RX
RS232
IR In
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
AV over IP Controller
1G Ethernet Switch
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
Decoder
DecoderDecoder
Decoder Video Wall
PC
Router

Page 9
Tel: [phone] www.scion-tech.co.uk [email protected]
6.4 Mode 3: Static IP mode
To setup AV over IP system, you need to set the IP management mode of the video LAN domain. The IP management modes are:
○Automatically managed by the controller box.
This is the mode as factory default. The IP address assignments to controller box video LAN, encoders and decoders will be man-
aged by the controller box firmware automatically. In this mode there is no need to add router in the system on video LAN domain.
○DHCP Mode
This is the mode for system in which there is a DHCP router on video LAN domain to assign IP addresses for controller box video
LAN, Encoders and Decoders. The router acts as a DHCP server . It’s recommended to set the net mask of router to 255.255.0.0.
●Static IP Mode by Manual setting
This is the mode for system in case IP address resources can be assigned manually for controller box video LAN, Encoders and De-
coders.
Reminders as below.
a. The network settings of controller box video LAN, Encoders and Decoders must be on the same subnet.
b. It’s recommended to set net mask of controller box video LAN, Encoders and Decoders to 255.255.0.0.
Back Next
Select “Static IP” Mode on the interface as shown below, then follow the steps is “Mode 1”.
User ManualSC08.CTL100HScion Tech
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
DVD Player
DVD
Encoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
Video LAN (PoE)
DC 12V IR OutIR In
TX GND RX
RS232
TX GND RX
RS232
TX GND RX
RS232 HDMI IN HDMI OUT
TV
Decoder
AV over IP Controller
1G Ethernet Switch
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)DC12V IROutIRIn TXGND RXRS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
VideoLAN (PoE)
DC12V IROutIRIn
TXGND RX
RS232
TXGND RX
RS232
TXGND RX
RS232 HDMIIN HDMIOUT
Decoder
DecoderDecoder
Decoder Video Wall
PC

Page 10
Tel: [phone] www.scion-tech.co.uk [email protected]
After entering the interface as shown in the dialogue box below, manually set the IP address, subnet mask and
gateway for the video LAN.
Controller Box Video LAN Port Settings
Back Next
IP Address 169.254.2.225
Subnet Mask 255.255.0.0
Gateway 169.254.2.1
Remember:
Once the Controller Box Video LAN network is set, the IP addresses of following discovered Encoders and De-
coders will be assigned to the same domain with Controller Box Video LAN. Please click the “Next” button to set
the IP address range of the Encoders and Decoders.
Note:
It’s highly recommended to use a different IP network domain from the Control domain.
After the progress reaches 100%, the following dialogue box will appear.
Encoders and Decoders IP Address Range Settings.
Back Next
Encoders IP Address Range 169.254.0.1
Decoders IP Address Range 168.254.0.1
Remember:
To easily manage the IP addresses of Encoders and Decoders, it’s strongly recommended that you set the IP ad-
dress of the Encoders and Decoders to different segments. For Example.
Encoders IP address from 169.254.3.1 to 169.254.3.254
Decoders IP address from 169.254.6.1 to 169.254.6.254
169.254.255.224
255.254.255.254
To
To
User ManualSC08.CTL100HScion Tech

Page 11
Tel: [phone] www.scion-tech.co.uk [email protected]
On this interface, you can set the IP address range of Encoders and Decoders. After the setting is complete,
click the “Next” button to enter the interface as shown in the figure below.
Now you can select to automatically add all discovered Encoders and Decoders to the project or just them in the
web page where you can add them manually.
●Automatically managed by the controller box.
○List all discovered Encoders and Decoders
Back Scan
Follow Step 1 to complete setup.
7.0 System Control
7.1 Preview
●Preview Page
●On this page, you can preview the Encoder/Decoder by clicking the drop down list on the right side.
User ManualSC08.CTL100HScion Tech
AVoIP Preview
Encoder 001 Decoder 001

Page 12
Tel: [phone] www.scion-tech.co.uk [email protected]
7.2 Matrix Control
Encoders: Display all the current Encoders. The text in the figure is the name of the device.
Decoders: Display all the current Decoders. The text on the first line is the name of the Decoder, and the text
on the second line refers to the Encoder where the signal resource is from.
Operating Instructions:
(1) If an Encoder shows “No Signal”, it means that the Encoder cannot be dragged.
(2) If there is an image on an Encoder, it means that the Encoder can be dragged. As shown in the figure
above, if an Encoder is dragged to the place where the red arrow points to, all Decoders will share the same
signal resource from this Encoder; if an Encoder is dragged to the place where the blue arrow points to, only
the indicated Decoder can receive signals from this Encoder.
User ManualSC08.CTL100HScion Tech
AVoIP Matrix Control
Encoders
Encoder 001 Encoder 002
Decoders
Decoder 001
TX: Encoder 001
Decoder 001
TX: Encoder 002
Decoder 001
TX: Encoder 003
Decoder 001
TX: Encoder 004

Page 13
Tel: [phone] www.scion-tech.co.uk [email protected]
7.3 Project Page
Current Devices: Devices that have been added to the current project.
Unassigned Devices: Devices not added to the current project.
Operating Instructions:
(1) Click “Display ID” to display the ID or PATTERN of the Decoders.
(2) Click “Save Project” to save the project file (config_file.json), so that you can use the saved project next
time without scanning devices again.
(3) Click “Clear Project” to clear the current project, then you will need to setup devices again.
(4) Click “Scan” to search devices that do not appear in the current project; Click “Stop Scan”, then it will stop
searching.
(5) Click “Configuration & Scan” to search new devices automatically and add to the current project.
User ManualSC08.CTL100HScion Tech
AVoIP Project
Current Devices Save ProjectDisplay ID Clear Project
Encoders
ID
1
2
3
4
Name
Encoder 001
Encoder 002
Encoder 003
Encoder 004
IP Address
169.254.3.6
169.254.3.1
169.254.3.7
169.254.3.4
Status
Offline
Offline
Offline
Offline
Encoders
ID
1
2
3
4
Name
Decoder 001
Decoder 002
Decoder 003
Decoder 004
IP Address
169.254.6.8
169.254.6.5
169.254.6.2
169.254.6.6
Status
Offline
Offline
Offline
Online
Unassigned Devices
Unassigned Encoders Unassigned Decoders
Configuration & Scan Scan

Page 14
Tel: [phone] www.scion-tech.co.uk [email protected]
7.4 Encoders
1.ID: The ID of the current device. (Note: ID is not duplicated.)
2.Name: The name of the current device. (Note: Name is not duplicated.)
3.MAC Address: The MAC Address of the current device.
4.IP Address: The IP Address of the current device.
5.Firmware: The Firmware version No. of the current device.
6.Status: The status (online or offline) of the current device.
7.EDID: The EDID of the current device.
8.Audio Selection: The Audio Selection of the current device.
Operating Instructions
Click “Refresh” to refresh the data of the current Encoders.
Click the drop-down list of EDID to set the current Encoder’s EDID.
Click the drop-down list of Audio Selection to set the current Encoder’s audio output.
Click the icon on the left of ID to check the detail information about the as shown in below:
User ManualSC08.CTL100HScion Tech
AVoIP Encoders
Refresh
ID
1
2
3
4
5
6
>
>
>
>
>
>
Name
Encoder 001
Encoder 002
Encoder 003
Encoder 004
Encoder 005
Encoder 006
MAC Address
6C:DF:FB:00:09:71
6C:DF:FB:00:09:72
6C:DF:FB:00:09:70
6C:DF:FB:00:09:73
6C:DF:FB:00:09:74
6C:DF:FB:00:09:75
IP Address
169.254.3.5
169.254.3.1
169.254.3.2
169.254.3.6
169.254.3.4
169.254.3.3
Firmware
1.00.21
1.00.21
1.00.21
1.00.21
1.00.21
1.00.21
Status
Online
Online
Online
Online
Online
Online
EDID
Default EDID
Default EDID
Default EDID
Default EDID
Default EDID
Default EDID
Audio Selection
HDMI
HDMI
HDMI
HDMI
HDMI
HDMI

Page 15
Tel: [phone] www.scion-tech.co.uk [email protected]
User ManualSC08.CTL100HScion Tech
AVoIP Encoders
Refresh
ID
1>
Name
Encoder 001
MAC Address
6C:DF:FB:00:09:71
IP Address
169.254.3.5
Firmware
1.00.21
Status
Online
EDID
Default EDID
Audio Selection
HDMI
Encoder 001
Name
Update ID
CEC Pass-Through
Power LED
Copy EDID
Serial Settings
Network Settings
Preview
Reboot
Replace (Must be offline)
Remove from Project
Factory Default Reset
Select
On
Off
Select a Decoder
Apply
Apply
Reboot
Replace
Remove
Reset

Page 16
Tel: [phone] www.scion-tech.co.uk [email protected]
7.5 Decoders
1.ID: The ID of the current device. (Note: ID is not duplicated.)
2.Name: The name of the current device. (Note: Name is not duplicated.)
3.MAC Address: The MAC Address of the current device.
4.IP Address: The IP Address of the current device.
5.Firmware: The Firmware version No. of the current device.
6.Status: The status (online or offline) of the current device.
7.Source: The signal source (Encoder) of the current device.
8.Scaler Resolution: The resolution of the current device.
9.HDR: The HDR status of the current device.
10.Function: The mode of the current device.
Operating Instructions:
1.Click “Refresh” to refresh the data of the current Decoders.
2.Click the drop-down list of Source to select the current Decoder‘s signal source.
3.Click the drop-down list of Scaler Resolution to select the current Decoder‘s resolution.
4.Click the drop-down list of HDR to turn on/off HDR.
5.Click the drop-down list of Function to select the current Decoder‘s mode.
6.Click the icon on the left of ID to check the detail information about the current Decoder, as shown in below:
User ManualSC08.CTL100HScion Tech
AVoIP
Decoders
Refresh
ID
1
2
3
4
5
6
>
>
>
>
>
>
Name
Decoder 001
Decoder 002
Decoder 003
Decoder 004
Decoder 005
Decoder 006
MAC Address
6C:DF:FB:00:09:97
6C:DF:FB:00:09:92
6C:DF:FB:00:09:94
6C:DF:FB:00:09:95
6C:DF:FB:00:09:93
6C:DF:FB:00:09:90
IP Address
169.254.6.6
169.254.6.7
169.254.6.2
169.254.6.3
169.254.6.1
169.254.6.8
Firmware
1.00.21
1.00.21
1.00.21
1.00.21
1.00.21
1.00.21
Status
Online
Online
Online
Online
Online
Online
Source
Encoder 005
Scaler Resolution
Encoder 005
Encoder 005
Encoder 005
Encoder 005
Encoder 005
Pass Through
Pass Through
Pass Through
Pass Through
Pass Through
Pass Through
HDR
On
On
On
On
On
On
Function
Matrix
Matrix
Matrix
Matrix
Matrix
Matrix

Page 17
Tel: [phone] www.scion-tech.co.uk [email protected]
User ManualSC08.CTL100HScion Tech
AVoIP Decoders
Decoder 001
Name
Update ID
CEC Pass-Through
Power LED
Copy EDID
Serial Settings
Network Settings
Preview
Reboot
Replace (Must be offline)
Remove from Project
Factory Default Reset
Select
On
Off
Select a Decoder
Apply
Apply
Reboot
Replace
Remove
Reset
Refresh
ID
1
>
>
>
>
>
>
Name
Decoder 001
MAC Address
6C:DF:FB:00:09:97
IP Address
169.254.6.6
Firmware
1.00.21
Status
Online
Source
Encoder 005
Scaler Resolution
Pass Through
HDR
On
Function
Matrix

Page 18
Tel: [phone] www.scion-tech.co.uk [email protected]
7.6 Locked Signal Routing
On this page, you can independently route the different signals between Encoder & Decoder devices. Please click
“Locked Routing Help” for details.
7.7 Video Wall Management
User ManualSC08.CTL100HScion Tech
Refresh
ID
1
2
3
4
5
Name
Decoder 001
Decoder 002
Decoder 003
Decoder 004
Decoder 005
IP Address
169.254.6.25
169.254.6.35
169.254.6.30
169.254.6.15
169.254.6.20
Video
Help
Audio IR Serial USB CEC
Follow Follow Follow Follow Follow Follow
Follow Follow Follow Follow Follow Follow
Follow Follow Follow Follow Follow Follow
Follow Follow Follow Follow Follow Follow
Follow Follow Follow Follow Follow Follow
AVoIP Locked Signal Routing
AVoIP Video Wall Management
Refresh
ID Name
Vertical Horizontal
Help
Video Wall List
Create
Remove
There are no video walls in your current project There are no video walls in your current project
Video Wall Name Configuration Name Class Name Config Source