Scitec AEGIS- 8128 User manual

Explanation of Controls
1) 0-9, “*”,“#”:press to dial telephone numbers.
2) FLASH key: press to generate a 600ms (0.6 seconds)
“hook flash.”
3) REDIAL key: press to redial the last number dialed.
4) IN USE LED Indicator – lights when the telephone is
“off-hook.”
5) Ringer Volume Switch – set to Hor L to adjust the
ringer level to high or low volume as desired. This
switch is located on the rear of the telephone.
6) P/T Switch:set to select pulse/tone dialing mode. This
switch is located on the rear of the telephone.
7) VOL key:press to adjust volume level for handset
receiver.
Using your Aegis 8128 telephone
To place a call: Lift the handset, then dial the telephone
number.
To answer a call: Lift the handset.
Solutions for voice, data, and video
1212 E. University Ave. Urbana, IL 61802
Toll-Free 800-451-4035 | Phone [phone] | Fax [phone]
[email protected] | www.scitecinc.com
Aegis 8128
Telephone User Guide
Unpacking your Aegis 8128 telephone
This package contains the following items:
•Telephone base unit
•Handset
•Coiled handset cord
•Straight line cord
•This user guide
Installation
Insert one end of the coiled handset cord into the jack on
the LEFT SIDE of the base unit. Insert the other end of the
coiled handset cord into the jack on the bottom end of the
handset. Place the handset in its cradle to depress the hook
switch. Connect the straight line cord between the wall jack
and line jack located on the rear of the telephone base unit.
Lift the handset. A dial tone should be heard in the receiver.

Required FCC Notice
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
On the bottom of this equipment is a label that contains, among other information, a product identifier
in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone
company.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the local
telephone company. The REN for this telephone is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a
REN of 0.3).
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice isn't practical,
the Telephone Company will notify you as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of this telephone. If this happens, the Telephone Company will provide
advance notice in order for you to make the necessary modifications in order to maintain uninterrupted
service.
If you experience trouble with this telephone, please contact Scitec, Inc. at [phone] for repair or
warranty information. If the trouble is causing harm to the telephone network, the Telephone Company
may request that you remove this equipment from the network until the problem is resolved.
The customer can do the following repairs: replacement of cords or handset; replacement of window
for telephone number.
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
This telephone cannot be used on Telephone Company provided coin service.
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of the Aegis 8128 telephone does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
This equipment is hearing aid compatible.
If the Aegis 8128 is used with a leased system, permission of the owner of the equipment must be
obtained for connection of the telephone because modification of the host system is often required.
Jacks
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
The Aegis 8128 telephone uses RJ11C USOC standard modular jacks.
Warranty
Scitec, Inc. (“Scitec”) warrants your Aegis 8128 to be free from defects in material and workmanship for
a period of one (1) year from the date of purchase.
This warranty applies only to the original purchaser, and only to products employed in normal use and
service in standard commercial offices, schools/universities, hotel/motel guest rooms, healthcare
facilities, and/or residences.
This Warranty is only valid for merchandise purchased directly from Scitec or from an authorized Scitec
dealer or distributor.
If this product is found to be defective within the terms of this warranty, Scitec's only obligation -- and
your exclusive remedy -- is the repair or replacement of this product, at Scitec's discretion, provided
that the product has not been damaged through misuse, abuse, accident, modification, alteration,
neglect or mishandling.
This warranty shall not apply to any product found to have been improperly installed, configured, or
used in any way not in accordance with the instructions supplied with this product.
For repair or replacement, please call Scitec at [phone] to request a “ Return Authorization
Form.” A simple one-page form and complete instructions will be sent to you, to be filled out and
returned to Scitec. You will be asked to describe the failure symptoms of your telephone, provide the
date purchased (and proof of purchase date if requested), and provide the name of the Scitec dealer or
distributor from which the telephone was purchased. The completed form may then be faxed or mailed
back to Scitec. Then, when your return authorization request has been approved, Scitec will contact
you with a “Return Authorization Number” which must be clearly placed on the outside of the box that
you use to return your telephone. You, the customer, are responsible for paying all shipping costs to
return your defective product to Scitec. Scitec then pays for shipping the repaired or replaced product
back to you.
Please note that Scitec will not accept, repair, or replace any products returned without a “Return
Authorization Number.” Any such product sent to Scitec without a “Return Authorization Number” will
either be returned at the customer’s expense or be disposed of.
Scitec does not warrant and specifically disclaims any warranty, whether express or implied, of the
fitness for a particular purpose other than the warranty contained herein. No implied warranty on this
product, created by state law, shall extend beyond the term of this warranty unless such law otherwise
provides.
Scitec specifically disclaims any liability and shall not be liable for any consequential or incidental loss
or damage, including but not limited to damages to any equipment with which this product is used.
Some states do not allow the exclusion or limitation of incidental or consequential damages so the
above limitations or exclusions may not apply to you.
No agent, representative, dealer or employee of Scitec has the authority to increase or alter the
obligations or terms of this Warranty. This Warranty gives you specific legal rights and you may have
other rights, which vary from state to state.