Scott iDXS 10L User manual

MODEL NO.: iDXS 10L
WIRELESS DOCKING STATION FOR
iPod/iPhone
LED LIGHT WITH SPEAKER
Instruction Manual

GB-1
PRECAUTIONS
Follow the instructions below to ensure the product is used safely and correctly.
PLACEMENT
.Do not use the unit in places which are extremely hot, cold, dusty, or humid.
.Place the unit on a flat, even surface.
.Do not restrict the airflow around the unit by placing it in a place with poor ventilation,
by covering it with a cloth, or by placing it on a carpet.
.Do not place the unit close to heat sources.
.Use the apparatus only in moderate climates.
.Do not expose the unit to rain or splash with water.
.Do not place objects filled with liquids, such as vases on the unit.
SAFETY
.When connecting and disconnecting the AC power cord, take hold of the plug and not
the cord. Pulling the cord may damage it and may be dangerous.
.The mains plug is used as the disconnect device. The plug must be easily accessible.
.When you are not going to use the unit for a long period of time, disconnect the AC
power cord from the AC mains outlet.
AC VOLTAGE
.Before use, check that the rated voltage of your unit matches your local voltage.
CONDENSATION
.When there is condensation inside the unit, it may not function normally. Unplug the
unit for 1 to 2 hours before turning the power back on, or gradually heat the room up
and dry the unit before use.
.Ensure a minimum distance of 5 cm around the unit for sufficient ventilation.
.Do not cover the ventilation openings.
BATTERIES
.Pay attention to the environmental aspects of battery disposal.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with
an arrowhead symbol
within a triangle is a
warning sign alerting the
user to the presence of
“dangerous voltage”
inside the unit.
ATTENTION: To reduce the
risk of electric shock, do not
remove the cover. There are no
user serviceable parts inside
the unit. Refer all servicing to
qualified personnel.
The exclamation mark
within a triangle is a
warning sign alerting the
user to the presence of
important instructions
accompanying the
product.

GB-2
Congratulations on your purchase of this wireless sound system that we hope will fully
meet your requirements. You can build and improve on the system with additions such
as:
LSX 10 LED light with Speaker
SBX 10 wireless subwoofer
Notes:
1. you can have up to eight groups.
2. A group can consist of :
-1 LED light
-1 LED light and 1 subwoofer
-2 LED lights
-2 LED lights + 1 subwoofer
3. However, the maximum number of units is limited to 8. Here are three examples
of the many possible combinations.
Example 1
Group 1 : 2 LED lights + 1 subwoofer
Group 2 : 2 LED lights + 1 subwoofer
Group 3 : 2 LED lights
Example 2
Group 1 : 2 LED lights
Group 2 : 2 LED lights
Group 3 : 2 LED lights
Group 4 : 2 LED lights
Example 3
8 groups of 1 LED light
TABLE OF CONTENTS
PRECAUTIONS…………………………………………………………………… 1
TABLE OF CONTENTS………………………………………………………….. 2
BOX CONTENTS……..…………………………………………………………… 2
LOCATION OF CONTROLS……………………………………………………... 3
POWER SUPPLY AND INSTALLATION……………………………………….. 4
BASIC OPERATION.……………………………………………………………… 4
PLAYING AN iPod/iPhone AND CHARGING THE iPod/iPhone BATTERY 5
USB DEVICE AND SD/MMC CARD OPERATION………………………….. 6
AUX IN FUNCTION……………………………………………………………….. 6
MAINTENANCE…………………………………………………………………… 6
TROUBLESHOOTING GUIDE………………………………………………….. 6
TECHNICAL SPECIFICATIONS………………………………………………… 7
BOX CONTENTS
1. Unit
2. LED Light with speaker
3. AC/DC adapter
4. Remote control with batteries
5. AUX sound cables (3.5mm to 3.5mm,
3.5mm to RCA)
6. iPhone adapters (3x)
7. Instruction manual

GB-3
LOCATION OF CONTROLS
RF 2.4 GHz wireless docking station
1. Power
ON/OFF
switch
2. DC IN 7.5V 1.5A jack
3. VIDEO OUT jack
4. AUX IN jack
5. SD/MMC card slot
6. USB port
7. standby LED
8. SD/MMC LED
9.
USB
LED
10. AUX IN LED
11. iPod LED
12. SW BASS LED (SBX 10 option)
13. Infrared Receiver Window (IR)
14. Docking station for iPod/iPhone
15. PAIR button
LED light with speaker
1. E27 screw
2. LED light
3. Pair button
4. Standby LED
5. Speaker
Remote control
1. MUTE
2. Source: iPod,AUX IN,USB,SD/MMC
3. VOL +/- (volume)
4. (Speaker) ON/OFF
5. Group control 1,2…8, ALL speaker/light on/off
6. (Standby/On)
7. (Play/Pause)
8. (Light) ON/OFF,DIM (Dimmer)
9. /(Previous/Next), /(Fast backward/forward)
10. SW BASS (for subwoofer (SBX 10) only)
iPod
2 3 4
5
6
789

GB-4
POWER SUPPLY AND INSTALLATION
Docking station
Connect the AC/DC adapter power cord to the mains with AC 100-240V ~ 50/60Hz
power source and the other end to the DC IN 7.5V 1.5A jack at the back.
LED light with speaker
Make sure the power source is switched off before installation.
Screw the LED light with speaker to an E27 socket with an AC 100-240V ~ 50/60Hz
power source.
Note: Do not use your external dimmer control that may cause the unit malfunction. To
dim the light, press the button repeatedly (Two levels are available).
Installing the remote control batteries
Remove the battery cover from the remote control and insert 2x AAA size batteries
(provided), ensuring the correct polarity as shown on the diagram inside the
compartment.
Precautions when using batteries
1. Use only batteries recommended by the manufacturer.
2. Do not mix different types of batteries together (e.g. alkaline, rechargeable or standard
(carbon zinc) or old batteries with fresh ones.
3. Exhausted batteries must be removed as they might leak.
4. Dispose of batteries properly according to environmental regulations.
BASIC OPERATION
Standby/On mode
Device
Standby
On
LED light with
speaker Standby LED:
LED light: On Off Off On
Docking station
Standby LED: Red Blue
Operation: Slide the power ON/OFF switch and press the button to
go to standby or on mode.
Note: Make sure the power supply of the LED light with speaker
is switched on or otherwise, the docking station cannot be
switched on.
Press the button to turn on/off the light.
Press the button to turn on/off the sound.
When there is no input or it is in pause mode for 10 minutes, the docking station will
automatically go to standby mode.
PAIRING
The docking station and LED light with speaker are paired in the factory (the station’s red
LED is on standby). If this LED blinks they are not paired. When the docking station is in
standby mode, use a sharp object (e.g. a paper clip) briefly to press the PAIR button
(pairing) under the docking station first and then, within one minute, briefly press the
PAIR button at the level of the transparent LED light with speaker cover. Both the
standby LEDs will blink rapidly until the pairing is successful.
It is possible to add a second light or a subwoofer to this group 1. These items must be
paired at the same time so they are in the same group. If you want to add another light
to group 1 to get a stereo effect (or a subwoofer to improve the bass), pairing has to be
reinitialized first. Use a pointed object to press the PAIR button under the docking to
station for ten seconds to reset it. The various blue LED lights (on the docking station)
blink for a few seconds then stop.
Then begin the above pairing operation again. Once group one is complete, simply
repeat the pairing operation to form group 2, and so on.

GB-5
Notes:
When two LED lights belong to the same group, they restore a stereo sound.
A subwoofer by itself cannot constitute a group.
Control of the groups
You can control the groups individually or all together. Select a group with the numerical
keypad then press Mute or button to adjust the sound or brightness of the lamps in
this group.
Docking station
Source
select
Press the source (
iPod
,
AUX IN
,
USB
,
SD/MMC
) button to
select the source. The selected source LED will be on.
VOLUME control
Use the
VOL
+/
-
buttons to adjust the volume level. The standby
LED flashes when pressing the VOL +/- button. It will not flash
when reaching at maximum or minimum volume level.
MUTE
Press the
MUTE
button on the remote control to turn off the
sound. Press the VOL +/- buttons again to resume the sound.
Subwoofer
BASS
Use with SBX10 Press the
SW
BASS
button to enhance the bass effect of the
subwoofer (SBX 10). When the bass function is on, the SW
BASS LED is on.
PLAYING AN iPod/iPhone AND CHARGING THE iPod/iPhone
BATTERY
Installing an adapter on the iPod/iPhone docking station
1. Use the iPod adapter supplied with your iPod or iPhone adapter supplied with this
unit.
2. Place the adapter on the docking station at the top of
the unit with the two tabs facing forwards.
3. To remove the adapter, press the back of the adapter
and pull it up.
Note: Ensure that the iPod/iPhone adapter is correctly installed on the docking station.
Listening to your iPod/iPhone
1. With the iPod/iPhone adapter installed, gently dock the iPod/iPhone (without the
protective cover) in the docking station.
2. Press the iPod/iPhone button to select the iPod/iPhone mode.
3. It automatically starts playback. Press to pause playback. Press it again to
resume normal playback.
4. Press the / buttons repeatedly to skip to the previous or next track.
5. Hold down these buttons to move fast forward or back.
6. Alternatively, you can use the controls on your iPod/iPhone.
Watching video from your iPod/iPhone
Use an RCA video cable (not supplied) to connect the VIDEO OUT jack of the docking
station to the TV video input jack. Set the TV output on your iPod/IPhone to ON and set
the TV to correct video mode.
Note:
The iPod/iPhone’s internal battery charges until it is fully charged.
Adjust the volume using the volume control button on the unit.
To prevent sound distortion during iPod/iPhone playback on this unit, the EQ function
in your iPod/iPhone must be set to “Off”.
The unit is not designed for playing and charging an iPod shuffle, but it is possible to
connect the iPod’s headphones jack to the AUX IN jack on the unit.

GB-6
USB DEVICE AND SD/MMC CARD OPERATION
Insert a USB device into the USB port and/or an SD/MMC card into the SD/MMC card
slot on the main unit. Press the USB or SD/MMC button to select the source. Same as
playing iPod/iPhone, use the and / buttons to play MP3/ WMA audio files. The
USB/SD/MMC LED will flash during playback.
Note: Due to specific technical features, some models of USB storage devices or MP3
players may take longer to be read or even may not be read.
AUX IN FUNCTION
This unit has an AUX IN jack which allows you to connect an external audio device such
as an MP3 player or earlier iPod model and DVD player.
1. Connect external sound unit to the AUX IN input of the docking station using one of
the auxiliary connection cables (supplied).
2. Once the two units are on, press the AUX IN button to select “AUX IN” mode.
3. Operate your external audio device as usual to select and play music.
4. Adjust the volume controls on both your external audio device and this unit to the
desired volume level.
5. MAINTENANCE
Care and maintenance
To clean the casing, unplug the unit and wipe off dust and stains with a soft, damp cloth.
Do not use benzene, thinner or similar chemicals to clean the casing.
If at any time in the future you want to dispose of this product, please note
that electrical products should not be disposed of with household waste.
Find out where your nearest recycling centre is. Consult your local authority
or retailer for more details (Waste Electrical and Electronic Equipment
Directive).
TROUBLESHOOTING GUIDE
Problems
Recommendations
1. The player or LED
light with speaker
does not work properly
1.1 Slide the power
ON/OFF
switch of the docking station.
1.2 Press the button to go to standby mode and press it
again to turn the unit back on
1.3 Reset the unit by unplugging the AC power cord for
few seconds, then plugging it back in.
1.4 Do pairing.
1.5 Do not use your external dimmer control.
2. No sound, poor sound 2.1 Check the cable connections.
2.2 Use the corresponding mode button to select the
correct mode.
3. USB device / card is
not read 3.1 Some external hard disks may not be supported. Hard disks that have built-in power supply should be
favored.
3.2 Check with the USB disk file system and format it with
FAT or FAT32.
3.3 Due to different formats, some models of USB/Card
storage devices or MP3 players may not be read
4. No sound, poor sound
in iPod/iPhone mode 4.1 Use correct iPod/iPhone adapter. 4.2 The EQ function in your iPod/iPhone must be set to
“Off”.
4.3 Your iPod/iPhone model is not supported by the unit.
Connect your iPod/iPhone to the docking station via
the AUX IN jack.

GB-7
TECHNICAL SPECIFICATIONS
LED light with speaker
Power source AC 100-240V ~ 50/60Hz
Light type LED, E27 screw
Lighting power 5 W
Light life 30000 Hours
Speaker 2.25”, 4 Ohm
Output power – Speaker 10 W (r.m.s.)
Total power consumption 20 W (Light with speaker)
Standby power consumption < 1 W
Dimensions 85 (Diameter) x 139 (H) mm
Weight 0.4 Kg
Docking station
Power source: AC/DC adapter Input: AC 100-240V ~ 50/60Hz
Output: DC 7.5V 1.5A
Wireless transmission RF 2.4 GHz, range 30 m (no wall)
The range will depend on the environmental
factors such as the number/ thickness of the
walls, doors or windows.
USB port type 2.0
Maximum handling capacity 32 GB
Card slot type SD/MMC
Maximum handling capacity 32 GB
Max. power consumption 10 W
Standby power consumption < 1.5 W
Dimensions 33.5 (H) x 154 (W) x 106(D) mm
Weight 0.2 Kg
Note: Due to continuing improvements, the technical specifications are subject to
change without notice.