Screen Innovations LinkPro Z User manual

LinkPro Z
Installation Instructions
Copyright 2019 US SHADE CORPORATION v. 1.0 4 December 2019
Screen Innovations
9715-B Burnet Rd, Suite 400 Austin, TX 78758
512.832.6939
www.screeninnovations.com

INITIAL CONSIDERATIONS
Thank you for your purchase of LinkPro Z.
This is a Zigbee Mesh Controller which operates at
2.4GHz. Minimize or eliminate any sources of RF
interference and shielding. Any metal, wire, or foliage
near the product can reduce or block the signal -
reducing the operating range of the device. Other
nearby transmitters may also cause interference.
Initial Considerations 1
Thank you for purchasing an SI product. If you have
any questions or need any assistance with your
LinkPro Z, we would love to help you.
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
[email protected]
LinkPro Z
Please use this QR Code to access more documents
and Video Tutorials related to the product.

PARTS IN THE BOX
LinkPro Z - Parts in the Box
LinkPro Z - Parts in the Box 32
(2) Mounting
Screws (PH2)
(2) Original Mounting
Ring Screws (PH2)
(1) Magnetic Mounting
Ring - Pre-installed
(1) LinkPro Z Unit
(1) 48v Passive PoE
Injector - Wall Wart
(1) 48v Passive PoE
Injector - Brick
(1) Injector Power Cable (1) 5 Meter CAT5e
(1) 2 Meter CAT5e
(2) Drywall
Anchors
(1) Original
Mounting Ring

LinkPro Z - Installation 5
3/4" hole for
CAT5e/6
properly spaced for a standard 4/0 ceiling junction
box if one is available). Drill holes using a 7/32" drill.
3. Drill a 3/4” hole in the center of the space illustrated
for the CAT5e/6 cable.
1. Position the Wall/ Magnetic mounting bracket in the
desired location in the orientation illustrated.
NOTE: Original Mounting Ring installation process is
similar to Magnetic Mount. For more details
contact support.
2. Mark the mounting hole locations (these holes are
Original Mounting RingMagnetic Mounting Ring
(preferred)
LinkPro Z - Installation 4
INSTALLATION - CEILING/WALL
MOUNT or MAGNETIC MOUNT
up
(cont. to next page)

6. Plug in the LinkPro Z and align the magnets on the
back of the device with two of the recessed areas
illustrated below. The magnets should fit snug in the
recessed areas, and the device should be flush
against the bracket.
LinkPro Z - Installation 7
4. Gently drive the drywall anchors into the 7/32" holes.
Locate your CAT5e/6 cable and pass it through the
hole drilled.
5. Mount the bracket to the ceiling using the provided
Phillips screws in the orientation illustrated.
LinkPro Z - Installation 6
(cont. to next page)

7. There should be an audible click.
LinkPro Z - Installation 9LinkPro Z - Installation 8
(cont. to next page)

8. Now connect the other end of your CAT5e/6 to a PoE
switch (sold seperately)/ PoE injector (incl.)
Plug it into PoE/
Power Output
Note: A valid LAN connection is highly recommended to connect to
the LAN port of these injectors, otherwise LinkPro Z will use WIFI.
10LinkPro Z - Installation

5. Click “+” to add an RTS product, then select the
appropriate product type (eg. “Roller Shade”).
6. Press “Next” to skip until at the pairing page.
7. Hold the "Program" button on the installation remote
until the shade jogs.
8. Press “Program” in the myLink app. The shade will
jog again.
9. Press “Create Group” and repeat steps 6 - 8 for all of
the shades in the room.
10. Name the group (this will be used for Amazon
Alexa).
For more details download the Programming Guide
pdf under resources at screeninnovations.com/
connectivity/linkpro-z/.
LinkPro Z - Set Up 13
NOTE: Before proceeding, ensure all Nano shades are
installed.
1. Download Somfy’s TaHoma application from the App
Store or Google Play.
2. Power your LinkPro Z using a PoE switch or the
provided PoE injector, and wait until the LED on the
LinkPro Z turns solid red.
3. Follow the in-app instructions to connect your
LinkPro Z (referred to as TaHoma in the application)
to the wireless network.
4. Once connected to WiFi, name the LinkPro Z and
select an icon.
SET UP
LinkPro Z - Set Up 12

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different
from that to which receiver is connected. Consult the dealer
or experienced radio technician for help.
NOTE: Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm
between the radiator & your body.
Changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate the equipment.
FCC INFORMATION
This device complies with Part 15 of the FCC Results.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including that which may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for CLASS B digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
www.screeninnovations.com/accessories/linkpro