Scrib3D P1 User manual

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS”or“PLA”will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS” or “PLA”will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS” or “PLA” will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS” or “PLA” will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS”or “PLA” will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS”or “PLA” will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

User Manual
Scrib3D P1
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Features and Controls of
your Scrib3D P1 3D Pen
FILAMENT
LOADER
TEMPERATURE
ADJUSTER
+
SPEED
ADJUSTER
+
FORWARD
REVERSE
LCD
SCREEN
LED:
TEMPERATURE
INDICATOR
LED:
POWER
INDICATOR
POWER
WARNI N G S
The Scrib3d P1 should only be used with
ABS, PLA filament approved by Scrib3d.
Misuse of your Scrib3d P1, setting your pen
to the wrong heating temperature, and/or
iuse of non-approved plastics or other
materials may result in damage to your pen
or injury to you, and will void your warranty.
Injuries to the user may include, but are not
limited to, harm sustained from inhaling
substances that are not suitable for heating;
or burns from flammable materials used in
the Scrib3d P1.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
DO NOT use the Scrib3D P1 near
bathtubs, showers, basins or other
vessels containing water. This could
result in death due to electric shock.
Allow the Nozzle to cool completely before
storing.
Unplug and set the Control Switch to OFF
when not in use or before storing.
- The Nozzle of the Scrib3D P1 can
become hot. DO NOT touch the Nozzle, or
you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the Pen is
hot and should not be touched.
This 3D Printing Device - when used
with a styrene filament (ABS / HIPS /
or PC-ABS) - can expose you and
others in the same room to styrene,
which is a chemical known to the State
of California to cause cancer. For more
information, go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A
WELL-VENTILATED AREA.
Getting Started
Product Overview
1. Connect the AC Adapter to an outlet. Plug
the AC Adapter Plug into the Power Socket of
the pen. The power indicator light should
become yellow. (Note: this 3D pen can be
used with a 3rd party power bank with at least
2 Amps output)
2. “ABS”or “PLA” will show on the Display, you
can use the Temperature Up/Down Buttons to
select a mode. Choose a mode that
corresponds to the type of plastic you are
using. (Note: using the wrong mode with the
wrong plastic will make for a poor experience
and possibly damage your pen)
3. Press the Forward Button to activate the
selected mode. You can use the Temperature
Up/Down Buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
200~230°C and PLA: 160-210°C. The
Temperature Indicator Light will be red while
heating up and will turn green when the pen
is ready.
4. Once the Temperature Indicator Light has
turned to Green, you can double click or hold
down the ForwardButton (Note: best to have
the speed at max). Straighten the end of the
lament you wish to use and load it into the
Filament Loader while the pen is running.
Once plastic starts extruding you are ready to
start creating in 3D!
P1 3D pen Power Adapter
(5V 2A)
Filament
The Display will ash either
ABS or PLA until the Forward
Button is pressed to chose a
mode. Then the screen will
Show desired temperature and
current temperature. The temp
LED will remain red while the
pen is heating up. Once it has
reached temp it will change to
Green. Then you can draw. You
Can ajust the temperature at any
time but to change from ABS to
PLA un-plug the pen and plug
it back in.
Wall outlet
DC 5V/2A
Once the temperature
indicator Light has changed
from red to green you can
load lament into the 3D
pen. Straighten the lament
at the end. Press and hold
the Feed Button or double
click for continuous mode.
Push the lament into the
pen until you can feel it
pulling it into the pen.

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[e-mail]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[e-mail] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[e-mail]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [e-mail]
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[e-mail]

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[e-mail]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[e-mail] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[e-mail]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [e-mail]
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[e-mail]

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[e-mail]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[e-mail] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[e-mail]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [e-mail]
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[e-mail]

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[e-mail]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[email protected] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[email protected]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [email protected]
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[email protected]

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[e-mail]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[email protected] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[email protected]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [email protected]om
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[email protected]

SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.35A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
For care and maintenance information, and more advice on how to
use your Scrib3d P1, please refer to our website: Scrib3dPen.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This Class B digital apparatus complies with Canadian
ICES-003
CAN ICES-3 (B)/NMB-3(B)
Manufactured by SCRIB3D LLC, and distributed by SCRIB3D LLC and
WobbleWorks, Inc. Address: 89 5th Avenue, Suite 602, NY, NY, 10003.
This product is protected by SCRIB3D LLC and WobbleWorks, Inc.
intellectual property. Please see the list of applicable WobbleWorks’
patents at http://PiKA3D.com/patents. PIKA3D is a trademark owned
by WobbleWorks, Inc. The PIKA3D pika character icon is the
copyrighted property of WobbleWorks, Inc. © SCRIB3D LLC &
WobbleWorks, Inc.
Designed in the USA.
Made in China, Guangdong.
ISSUES?
Before returning to the
retailer see if we can help
Check out our tutorials:
SCRIB3dPen.com/tips
Need more help? Contact us
[email protected]
We recommend only using the
Reverse button when removing
and changing lament. If only
partially withdrawn, lament
can swell in the pen and create
jams. If this happens, fully
withdraw the lament and cut
the swollen part o.
Filament quality varies greatly.
We always recommend using
Scrib3D lament, and storing it
in a sealed and dry location.
Plastic may continue to
ooze slightly after the
pen stops. This is more
pronounced with PLA.
This is a common
Phenomenon (i.e. glue
guns and 3D printers). If
you see this happening,
slightly decrease the
temperature.
When using your
Scrib3D P1 3D Pen you
will nd the best
results for drawing at
object and on surface
from holding the pen
at an angle of 65
dagrees or higher.
Snip those tips! when you change plastic or before
you insert a new strand make sure the lament has
a at surface so it can push the previous lament.
Failure to cut the end o the plastic can result in
jams or pens not extruding. Check out tips on how
to solve such issue on page 6.
Troubleshooting
Temperature Tuning
1. If when using the pen you see the plastic
bubbling or you hear a crackling noise coming
from the plastic your temperature might be too
high. Try lowering it 5~10°C and see if that
helps.
2. Filament should come out smooth and with
out much bubbling but it is normal to have
some small bubbling.
3. While some plastics like PLA are more prone
to oozing, if you nd that your oozing a lot of
plastic you can turn the temperature down on
the pen to help mitigate this. Also check that
you are using the correct lament setting
4. If the lament color looks dim and dark and
you can hear the motor struggling. This means
the temperature is too low increase the
temperature by 5~10°C.
For more help getting started, tips
and tricks, trouble shooting and to
learn more check out our website
www.Scrib3dPen.com or our
youtube channel (scan the QR code).
Problem Reasons Solution
Power indicator
Light will
not turn on
Issue with the AC adapter
or plug
Issue with the electronics
of the pen
Issue with the power socket
of the pen
Replace the AC adapter
with another: 5v, 2A, 3.8mm
barrel center + adapter
The pen’s electronics need
servicing please contact
[email protected] if
the pen is under warranty
Nothing is coming
out of the nozzle
The temperature is not high
enough or the wrong mode
for plastic was selected
Check mode the pen is in is
correct of the plastic you are
using. You can also try
adjusting the temp manually
Filament has stripped
ie. a chunk has been
taken out of the lament
and the drive system can’t
push it anymore
Reverse the lament out of
the pen. Cut o the damaged
portion and throw it away
and try again
Filament won’t go in Make sure the lament has
a at surface on the end
going into the pen
No motor noise
Possible issue with the
electronics or the motor.
Please contact us at
[email protected]
Pen not heating up Probem with the heating
element/nozzle
Motor is struggling Could be an issue with the
lament inside
Reverse out the lament. Cut
o any swollen or deformed
parts and cut a new end
before reinserting.
NOTE: Your pen will go into sleep mode after being inactive for 5
minuts (as a safety feature). Click any button to wake it up and
restart the heating sequence.
Here are some common problems and possible solutions to these
issue. If you can’t resolve the issue please reach out to our
customer service by email us at [email protected]om
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
Please contact
customer service at
[email protected]