SCT RemoteCam5 Instructions for use

RemoteCam5™ Quick Install
DATE: 8/28/15
PRELIMINARY
www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2015
Thank you for choosing the Sound Control Technologies’ RemoteCam5™ camera integration kit!
Included in each RemoteCam5™ kit will be:
1 Power Supply & cord (Currently all RemoteCam Kits utilize
the WPS-12) to provide power for the RemotCam5™
electronics as well as the remote camera up to 300’ from the
head end. All the RemoteCam™ kits use the same power
supply. The power supply is AC 100-240V~47-63HZ compliant.
1 RemoteCam5™ Head End Module (RC5-HE) which provides
system power, control interface (Ethernet & IR) for the
camera & one HDMI video output for the codec.
1 RemoteCam5™ Camera Module with PowerSniffer™ (RC5-
CE) that provides camera power, control (Ethernet & IR) and
HDMI video input for the camera
Documentation
Specific cables (P/N according to the following chart)
Company
Codec
Camera
SCT Kit
Cables
Cisco
SX80
Precision 60
RC5-P60
RCC-C001/RCC-C002/PPC-003
RCC-H001/RCC-H016
C40, C60, C90 &
SX80
SpeakerTrack 60
RC5-CST
2 x RCC-C001/RCC-C002
PPC-003
2 x RCC-H001/RCC-H016
Panasonic
Generic
Controller
Panasonic
AW-HE130
AW-HE40
RC5-P13
RCC-C001/RCC-C002/PPC-005
RCC-H001/RCC-H016
Sony
RMP10 or
Generic
Controller
Sony
SRG-120H
SRG-300H
RC5-S12
RC5-S30
RCC-C001/RCC-C002/PPC-004
RCC-H001/RCC-H016
To proceed with the installation, insure that you have installed one CAT5e or CAT6 cable between
the camera installation site and the codec installation site.
Minimum distance should be approximately 20’/6M.

www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2015
The cable must be wired for either UTP 568A or UTP 568B. For your convenience, you can use the
above scheme.
To install the RemoteCam5™ Kit, follow this step-by-step guide:
Step 1
Test and verify the Cat5e or Cat6 cable for UTP 568A or 568B wiring: See steps 2 & 3.
Step 2
Install the RC5-HE Head-End Module at the rack/equipment location.
Connect the Cat5e or Cat6 cable only to the RC5-HE module.
Connect the power supply to the RC5-HE Module.
Step 3
Using the PowerSniffer™, at the Camera Location connect to the UTP cable. When properly
terminated the PowerSniffer™ will display 8 green LED’s.
Any other result, please re-terminate.
Step 4
Disconnect the power supply from the RC5-HE
Step 5
Connect the CAT5e or CAT6 cable to the RC5-CE Camera Module.
Step 6
Connect provided cables between codec and RC5-HE module.
Step 7
Connect provided cables between camera and RC5-CE module.
Step 8
Connect the power supply to RC5-HE module
LED Behavior:
Head-End Module HDCP LED: Blinking = HDCP Inactive, Solid = HDCP Active
Head-End Module Link LED: Blinking Red = No Link, Blinking Red to Green = Link Active
Camera Module: LED will be Red until Link is established, Solid Green when Link is Active
Step 9
Enjoy!