SCV SCV-xxEA User manual

AIR-COOLED
MODULAR CHILLER UNIT
INSTALLATION AND
USER MANUAL
SCV-xxEA
AIR CONDITIONING


“Originalinstructions”

MAIN PARTS OF THE UNIT
ACCESSORIES
1)SCV - 300E A
Temperature
testing
components of
total water outlet
11
11
Purpose
Shape
Qty.
Unit
transformer
Installation
&
Operation
Manual
Use for installation (only need for
setting the main module)
Installation
manual of wired
controller
1
1
2
8
7
9
4
6
3
5

2)SCV-600EA
NO.
NAME
12 3 4 5 6 7
Air outlet Top cover
Air inlet
Electric
control box CondenserCompressor Evaporator
NO.
NAME
89
Water outlet
Water intlet
1
2
8
7
9
4
6
3
5

1
I&O manual
OPERATION & PERFORMANCE
Performance characteristics of the unit
Use conditions of the unit
The air-cooled heat pump Modular unit is composed of one or more modules. Each module has its own independent electric
control unit, and the electric control units of modules conduct information exchange through communication network. The
air-cooled heat pump Modular unit is characteristics of compact structure and easy transportation and lifting, and in the meanwhile,
it also saves facilities, including cooling tower, cooling pump, and so on, for the user, and reduces installation cost.
The units provide central air handling devices or terminal equipment with chilled water or hot water. The unit is a completely
independent entirety type one, which is designed to be installed outdoors (on the ground or the roof). Each unit includes such main
parts as high-efficient and low-noise Modular compressor, air-cooled condenser, shell and tube (or plate) evaporator,
micro-computer control center, and so on. These parts are installed on steel structure base, so they are sound and durable.
The unit applies Chinese micro-computer control system, which can automatically conduct energy control according to the
magnitude of load, to achieve optimal matching and thus actually realizing optimal energy-saving operation. The product is
Modularized unit, and parallel connection of 16 modules can be realized at most, so the user can adopt module combination
according his own demands. The product can be widely applied in air-conditioning engineering of various newly-built and rebuilt
industrial and civil buildings, such as restaurant, hotel, apartment, office building, hospital, industrial plant, and so on. The
air-cooled heat pump Modular unit is the best choice for the place which has high requirement in noise and ambient environment
and which is short of water.
The A-weighted sound pressure level is below 70 dB.
（Unit:℃）
Ambient
temperature
Outlet water
temperature
Heating operating range
SCV -300E A SCV -300E A
a. The standard voltage of power supply is 380-415V 3N~50Hz, the minimum allowable voltage is 342V, and the maximum voltage is
456V.
b. To maintain better performance, please operate the unit under the following outdoor temperature:
（Unit:℃） Outlet water
temperature
Cooling operating range
SCV -600E A SCV -600E A
Ambient
temperature
510 20150
-15
-5
5
15
25
35
45
52
25 30 40 45 50 52 55
-15
-10
-7
-4
0
30
If the user requires the unit to operate under the outlet water temperature is lower than
the minimum setting value mentioned above, be sure to make the requirement to the dealer or
our maintenance center, and necessary protective measures should be taken before the unit
is used.

1. PRECAUTIONS
To prevent injury to the user or other people and property
damage, the following instructions must be followed. Incorrect
operation due to ignoring of instructions may cause harm or
damage.
Ask your dealer for installation of the air conditioner.
Incomplete installation performed by yourself may result in a
water leakage, electric shock, and fire.
Ask your dealer for improvement, repair, and
maintenance.
Incomplete improvement, repair, and maintenance may
result in a water leakage, electric shock, and fire.
In order to avoid electric shock, fire or injury, or if you
detect any abnormality such as smell of fire, turn off the
power supply and call your dealer for instructions.
Never replace a fuse with that of wrong rated current or
other wires when a fuse blows out.
Use of wire or copper wire may cause the unit to break down
or cause a fire.
Do not insert fingers, rods or other objects into the air
inlet or outlet.
When the fan is rotating at high speed, it will cause injury.
Never use a flammable spray such as hair spray,
lacqueror paint near the unit.
It may cause a fire.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
CAUTION
This appliance is intended to be used by expert or
trained users in shops, in light industry and on farms, or
for commercial use by lay persons.
Do not use the air conditioner for other purposes.
In order to avoid any quality deterioration, do not use the unit
for cooling precision instruments, food, plants, animals or
works of art.
Before cleaning, be sure to stop the operation, turn the
breaker off or pull out the supply cord.
Otherwise, an electric shock and injury may result.
In order to avoid electric shock or fire, make sure that an
earth leak detector is installed.
Be sure the air conditioner is grounded.
In order to avoid electric shock, make sure that the unit is
grounded and that the earth wire is not connected to gas or
water pipe, lightning conductor or telephone earth wire.
In order to avoid injury, do not remove the fan guard of
the outdoor unit.
Never inspect or service the unit by yourself.
Ask a qualified service person to perform this work.
Do not dispose this product as unsorted municipal
waste.Collection of such waste separately for special
treatment is necessary.
Keep far away from high-frequency equipment.
Keep away from the following places:
a place where it is full of oil gas; places where salty air
surrounding(near the coast); a place where is caustic gas(the
sulfide in hotspring). Location in the folling places may cause
malfunction or shorten the life span of the manchine.
In the cace of extremely strong wind, please prevent the
air from flowing backwards into the outdoor unit.
Snow canopy is necessary in sonwfall places on the
outdoor unit. Please consult the local dealer for details.
In the frequent thunderstruck place, lightning proof
actions should be taken.
To prevent refrigerant leak, contact your dealer.
When the system is installed and runs in a small room, it is
required to keep the concentration of the refrigerant, if by any
chance coming out, below the limit. Otherwise, oxygen in the
room may be affected, resulting in a serious accident.
The refrigerant in the air conditioner is safe and normally
does not leak.
If the refrigerant leaks in the room, contact with a fire of a
burner, a heater or a cooker may result in a harmful gas.
Turn off any combustible heating devices, ventilate the
room, and contact the dealer where you purchased the
unit.
Do not use the air conditioner until a service person confirms
that the portion where the refrigerant leaks is repaired.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
WARNING
WARNING
Failure to observe a warning may result in death.
CAUTION
The safety precautions listed here are divided into two categories. In
either case, important safety information is listed which must be read
carefully.
Failure to observe a caution may result injury or damage
to the equipment.
I&O manual
2
I&O manual
2
CONTENTS PAGE
PRECAUTIONS..........................................................................2
TRANSPORTATION ...................................................................................3
INSTALLATION OF THE UNIT ....................................................................4
WATER SYSTEM INSTALLATION..............................................................7
ELECTRIC WIRING..................................................................................14
TRIAL RUN..............................................................................................19
USE.........................................................................................................20
MAINTENANCE AND UPKEEP .................................................................24
APPLICABLE MODELS AND MAIN PARAMETERS...............................30
ATTACHED PICTURE (I) .........................................................................31
ATTACHED PICTURE (II)......................................................................32

Do not operate the air conditioner with a wet hand.
An electric shock may happen.
Do not touch the heat exchanger fins.
These fins are sharp and could result in cutting injuries.
After a long use, check the unit stand and fitting for
damage.
If damaged, the unit may fall and result in injury.
To avoid oxygen deficiency, ventilate the room
sufficiently if equipment with burner is used together
with the air conditioner.
Arrange the drain hose to ensure smooth drainage.
Incomplete drainage may cause wetting of the building,
furniture etc.
Never expose little children, plants or animals directly to
the air flow.
Adverse influence to little children, animals and plants may
result.
Notice to avoid places where operation noise may easily
be spread away or be enhanced.
Noise can be amplified by anything blocking the air outlet
of outdoor unit.
Choose a proper place that the noise and hot or cold wind
blown out of the outdoor unit will not bring inconvenience to
your neighbors and not affect the growth or animal or plant.
2. TRANSPORTATION
Recommending locate and operate the equipment at the
altitude height not exceeded than 1000m.
Endurable temperature during transportation is -25℃~55℃.
Such equipment could endure 70℃of the maximum
temperature in 24hrs.
Do not allow a child to mount on the outdoor unit or avoid
placing any object on it.
Falling or tumbling may result in injury.
Do not operate the air conditioner when using a room
fumigation - type insecticide.
Failure to observe could cause the chemicals to become
deposited in the unit, which could endanger the health of
those who are hypersensitive to chemicals.
Do not place appliances which produce open fire in places
exposed to the air flow from the unit or under the indoor unit.
It may cause incomplete combuston or deformation of the
unit due to the heat.
Do not install the air conditioner at any place where
flammable gas may leak out.
If the gas leaks out and stays around the air conditioner, a
fire may break out.
The appliance is not intended for use by young children or
infirm persons withoutsupervision.
Young children should be supervised to ensure that they do
not play with the appliance.
Handling of the unit
The angle of inclination should not be more than 15º when carrying the unit, to avoid overturn of the unit.
a. Rolling handling: several rolling rods of the same size are placed under the base of the unit, and the length of each rod must be
more than the outer frame of the base and suitable for balancing of the unit.
b. Lifting: the strength lifting rope (belt) can bear should be 4 times the weight of the unit. Check the lifting hook and ensure that it is
firmly attached to the unit. To avoid damages to the unit, the contact position of the unit and lifting rope should be provided with an at
least 50mm thick wood block, cloth or hard paper. Any person is not allowed to stand below the unit when lifting it.
Fig. 2-1 Lifting of the unit
3
I&O manual
Lifted cable Lifted cable
Lifted hook
Thickness wood,
cloth or hard
paper (4 places)
UNIT
Hoisting installation,
unilateral distance
from unitbody should
not less than 50mm

3. INSTALLATION OF THE UNIT
3.1 Selection of installation sites
3.1.1 The unit can be installed on the ground or on the
suitable roof, but enough ventilation volume should be
ensured in both cases.
3.1.2 The unit should not be installed where noise and
vibration are required to a certain extent.
3.1.3 The installed unit should be sheltered from direct
sunlight as much as possible, and be far away from
boiler flues and ambient air which may erode condenser
coils and copper tube parts of the unit.
3.1.4 If the installed unit can be approached by
unauthorized persons, safety measures of isolation
should be taken, such as rail guards. These measures
will avoid artificial damages and accidental damages,
and prevent the control boxes from being opened leading
to exposure of electric components in operation.
3.1.5 The height of the installation foundation for the unit
should not be less than 300mm, and floor drains are
required in installation sites, to ensure smooth drainage
and remove any seeper.
3.1.6 In case of installation on the ground, the steel base
of the unit should be located on the concrete foundation,
and the concrete plinth should extend below frozen soil
layer. The foundation of the unit should not be connected
to the foundation of the building, to avoid affecting the
people due to transfer of noise and vibration. The base
of the unit is provided with installation holes, which can
be used to connect the unit and the foundation firmly.
3.1.7 In case of installation on the roof, the roof must
possess enough strength to sustain weight of the unit
and maintenance personnel. The unit can be supported
on concrete foundations or channel steel frames similar
to those used in the unit installation on the ground. The
load-bearing channel steel must be in alignment with the
installation holes of the unit damper, and the channel
steel should possess enough width for installing the
damper.
3.1.8 Consult the building contractor, the architectural
designer or other specialists about the cases with special
installation requirements.
NOTE
The selected installation site of the unit should facilitate connection
of water pipes and wires, and be free from water inlet of oil fume,
steam or other heat sources. Besides, the noise of the unit and cold
and hot air should not influence the surrounding environment.
3.2 Outline dimensional drawing
Front view
Left view
Top view
I&O manual
4
3.2.1 SCV-300EA
3.2.2 SCV-600EA
E
D
F
B
Fig. 3-1
A
C
Front view
A
B
Top view
C
Left view
F
D
E
Front view

Table 3-1
3.3 Requirements of arrangement space of the unit
3.3.1 Requirements of arrangement space of the unit
3.3.1.1 To ensure adequate airflow entering the
condenser, the influence of descending airflow caused by
the high-rise buildings around upon the unit should be
taken into account when installing the unit.
3.3.1.2 If the unit is installed where the flowing speed of
air is high, such as on the exposed roof, the measures
including sunk fence and Persian blinds can be taken, to
prevent the turbulent flow from disturbing the air entering
the unit. If the unit needs to be provided with sunk fence,
the height of the latter should not be more than that of
the former; if Persian blinds are required, the total loss of
static pressure should be less than the static pressure
outside the fan. The space between the unit and sunk
fence or Persian blinds should also meet the requirement
of the minimum installation space of the unit.
3.3.1.3 If the unit needs to operate in winter, and the
installation site may be covered by snow, the unit should
be located higher than the snow surface, to ensure that
air flows through the coils smoothly.
A
B
D
C
E
Fig. 3-3
Input of airflow
Input of airflow
Input of airflow
Input of airflow
Installation space (mm)
A
B
C
D
E
≥800
≥2000
≥2000
≥800
≥6000
Table 3-2
NOTE
After installing the spring damper, the total height of the unit will
increase by 135mm or so.
The ports of inlet and outlet pipes should be flange ports, and
flanges should be hubbed slip-on-welding steel pipe flanges.
5
I&O manual
Bottom view
G
H
Hole for anchor boltΦ15
A
Main unit
Main unit
Fig. 3-2
A
B
C
D
E
F
G
H
Model
2220
1055
1325
234
210
470
1105
958
SCV-300EA SCV-600EA
1870
1000
1175
204
200
470
788
880

3.4 Space requirements for parallel installation of
multiple Modular units
To avoid back flow of the air in the condenser and operational
faults of the unit, the parallel installation of multiple Modular
units can follow the direction A and D as shown in Fig. 3-2, the
spaces between the unit and the obstacle are given in Table
3.1, and the space between adjacent Modular units should not
be less than 300mm; the installation can also follow the
direction B and C as shown in Fig. 3-2, the spaces between the
unit and the obstacle are given in Table 3-1, and the space
between adjacent Modular units should not be less than
600mm; the installation can also follow the direction
combination of A and D, and B and C, the spaces between the
unit and the obstacle are given in Table 3-1, the space between
adjacent Modular units in the direction A and D should not be
less than 300mm, and the space between adjacent Modular
units in the direction B and C should not be less than 600mm.
If the spaces mentioned above cannot be met, the air passing
from the unit to the coils may be restricted, or back flow of air
discharge may occur, and the performance of the unit may be
affected, or the unit may fail to operate.
3.5 Installation foundation
a. The unit should be located on the horizontal foundation, the
ground floor or the roof which can bear operating weight of the
unit and the weight of maintenance personnel. Refer to Table
9.1 (Table of applicable models and parameters) for operating
weight.
b. If the unit is located so high that it is inconvenient for
maintenance personnel to conduct maintenance, the suitable
scaffold can be provided around the unit.
c. The scaffold must be able to bear the weight of maintenance
personnel and maintenance facilities.
d. The bottom frame of the unit is not allowed to be embedded
into the concrete of installation foundation.
3.5.1 Location drawing of installation foundation of the unit: (unit:
mm)
80
Cement mortarConcreteDrainage channel
Fig. 3-6
3.6 Installation of damping devices
3.6.1 Damping devices must be provided between the unit
and its foundation.
By means of the Φ15mm diameter installation holes on the
steel frame of the unit base, the unit can be fastened on
the foundation through the spring damper. See
Fig.3-3(Schematic diagram of installation dimension of the
unit) for details about center distance of the installation
holes. The damper does not go with the unit, and the user
can select the damper according to the relevant
requirements. When the unit is installed on the high roof or
the area sensitive to vibration, please consult the relevant
persons before selecting the damper.
3.6.2 Installation steps of the damper
Step 1. Make sure that the flatness of the concrete
foundation is within ±3mm, and then place the unit on the
cushion block.
Step 2. Raise the unit to the height suitable for installation
of the damping device.
c. Remove the clamp nuts of the damper.
Step 3. Place the unit on the damper, and align the fixing
bolt holes of the damper with the fixing holes on the unit
base.
Step 4. Return the clamp nuts of the damper to the fixing
holes on the unit base, and tighten them into the damper.
Step 5. Adjust the operational height of the damper base,
and screw down the leveling bolts. Tighten the bolts by
one circle to ensure equal height adjustment variance of
the damper.
Step 6. The lock bolts can be tightened after the correct
operational height is reached.
Damping device
Anchor bolt M12
Nut
Ferrol
It is recommended that the damper should be fastened on
the foundation with the provided holes. After the unit is
placed on the foundation, the damper connected with the
unit should not be moved, and the central clamp nut is not
allowed to be tightened before the damper sustains load.
Fig. 3-7
NOTE
I&O manual
6
Fig. 3-4
Schematic diagram of installation dimension of SCV-300EA
2000
Drainage channel
Anchor bolt
788
880
Fig. 3-5
Schematic diagram of installation dimension of SCV-600EA
2040
Drainage channel
Anchor bolt
1105
958

4. WATER SYSTEM INSTALLATION
4.1 Basic requirements of connection of chilled
water pipes
CAUTION
●After the unit is in place, chilled water pipes can be laid.
●The relevant installation regulations should be abided with
when conducting connection of water pipes.
●The pipelines should be free of any impurity, and all chilled
water pipes must conform to local rules and regulations of
pipeline engineering.
k. All low positions of the water system should be provided
with drainage ports, to drain water in the evaporator and the
system completely; and all high positions should be supplied
with discharge valves, to facilitate expelling air from the
pipeline. The discharge valves and drainage ports should
not be under heat preservation, to facilitate maintenance.
l. All possible water pipes in the system to be chilled should
be under heat preservation, including inlet pipes and flanges
of the heat exchanger.
m. The outdoor chilled water pipelines should be wrapped
with an auxiliary heating belt for heat preservation, and the
material of the auxiliary heat belt should be PE, EDPM, etc.,
with thickness of 20mm, to prevent the pipelines from
freezing and thus cracking under low temperature. The
power supply of the heating belt should be equipped with an
independent fuse.
n. When the ambient temperature is lower than 2℃, and the
unit will be not used for a long time, water inside the unit
should be drained. If the unit is not drained in winter, its
power supply should not be cut off, and the fan coils in the
water system must be provided with three-way valves, to
ensure smooth circulation of the water system when the
anti-freezing pump is started up in winter.
o. The common outlet pipelines of combined units should be
provided with mixing water temperature sensor.
WARNING
●For the water pipeline network including filters and heat
exchangers, dreg or dirt may seriously damages the heat
exchangers and water pipes.
●The installation persons or the users must ensure the
quality of chilled water, and de-icing salt mixtures and air
should be excluded from the water system, since they may
oxidize and corrode steel parts inside the heat exchanger.
7
I&O manual
●Connection requirements of chilled water pipes
a. All chilled water pipelines should be thoroughly flushed, to
be free of any impurity, before the unit is operated. Any
impurity should not be flushed to or into the heat exchanger.
b. Water must enter the heat exchanger through the inlet;
otherwise the performance of the unit will decline.
c. The inlet pipe of the evaporator must be provided with a
target flow controller, to realize flow-break protection for the
unit. Both ends of the target flow controller must be supplied
with horizontal straight pipe sections whose diameter is 5
times that of the inlet pipe. The target flow controller must be
installed in strict accordance with “Installation & Regulation
Guide for Target Flow Controller” (Figure 4.3~4.4). The wires
of the target flow controller should be led to the electric
cabinet through shielded cable (see Electric Controlling
Schematic Diagram for details). The working pressure of the
target flow controller is 1.0MPa, and its interface is 1 inch in
diameter. After the pipelines are installed, the target flow
controller will be set properly according to the rated water
flow of the unit.
d. The pump installed in the water pipeline system should be
equipped with starter. The pump will directly press water into
the heat exchanger of the water system.
e. The pipes and their ports must be independently
supported but should not be supported on the unit.
f. The pipes and their ports of the heat exchanger should be
easy to disassemble for operation and cleaning, as well as
inspection of port pipes of the evaporator.
g. The evaporator should be provided with a filter with more
than 40 meshes per inch at site. The filter should be
installed near to the inlet port as much as possible, and be
under heat preservation.
h. The by-pass pipes and by-pass valves as shown in Fig.
4-1 must be mounted for the heat exchanger, to facilitate
cleaning of the outside system of water passage before the
unit is adjusted. During maintenance, the water passage of
the heat exchanger can be cut off without disturbing other
heat exchangers.
i. The flexible ports should be adopted between the interface
of the heat exchanger and on-site pipeline, to reduce
transfer of vibration to the building.
j. To facilitate maintenance, the inlet and outlet pipes should
be provided with thermometer or manometer. The unit is not
equipped with pressure and temperature instruments, so
they need to be purchased by the user.

4.2 Connection drawing of pipeline system
8
I&O manual
Stop valve Pressure gauge Gate valve
Flexible joint
Y-shaped filter Thermometer Circulating pump Check valve
Automatic discharge valve
Symbol explanation
Fig. 4-1
Main unit
Expansion tank
Water replenishing
Dirt discharge valve
Differential pressure by-pass valve
Drain valve
Two-way valve
Three-way valve
Terminal
Auxiliary electric heater
unit
unit
Y-type filter,
requiring≥16 mesh
This is the water system of standard module, which pump is not provided.

9
I&O manual
In certain occasion (especially in manufacture cooling
process), for conforming the system water content requirement,
it’s necessary to mount a tank equipping with a cut-off baffle at the
system to avoid water short-circuit, Please see the following
schemes:
kW is the unit for cooling capacity and L is the unit for G
water flow in the formula counting the minimum water flow.
Comfortable type air conditioner
G= cooling capacity×2.6L
Process type type cooling
G= cooling capacity×7.4L
Error
Recommendation
Fig.4-4
Recommendation
Error
4.7 Selection and installation of the pump
4.7.1 Select the pump
a. Select the water-flow of the pump
The rated water-flow must no less than the unit rated water-flow;
in terms of multi-connect the units, that water-flow must no less
than total units’ rated water-flow.
b. Select the left of the pump.
H=h1+h2+h3+h4
H: The lift of the pump.
h1: Main unit water resistance.
h2: Pump water resistance.
h3: Water resistance of the longest water-loop distance,
includes: pipe resistance, different valve’s resistance, flexible
pipe resistance, pipe elbow and three-way resistance, two-way
resistance or three-way resistance, as well as filter resistance.
H4: the longest terminal resistance.
4.7.2 Installation the pump
a. The pump should be installed at the water inlet pipe, both of
which sides must mount the soft connectors for vibration-proof.
b. The backup pump for the system (recommended).
c. Units must with a main unit controls (Please see Fig. 5-3 for
the controls wiring diagram).
4.3 Design of the tank in the system
The minimum chilled water flow is shown in the table 4-1
If the system flow is less than the minimum unit flow rate,
the evaporator flow can be recirculated, as shown in the
diagram.
4.5 Maximum chilled water flow
The maximum chilled water flow is limited by the permitted
pressure drop in the evaporator. It is provided in the table 4-1
If the system flow is more than the maximum unit flow rate,
bypass the evaporator as shown in the diagram to obtain a lower
evaporator flow rate.
4.4 Minimum chilled water flow
For maximum chilled water flow rate
Evaporator
Recirculation
For minimum chilled water flow rate
Fig. 4-2
4.6 Minimum and Maximum water flow rates
Evaporator
Recirculation
Fig. 4-3
Table 4-1
Waterflow rate(m3/h)
Maximum
Minimum
Item
Model
13.0
SCV-600EA
8.0
6.4
SCV-300EA
3.8

4.8 Water quality control
4.8.1 Water quality control
When industrial water is used as chilled water, little furring may
occur; however, well water or river water, used as chilled water,
may cause much sediment, such as furring, sand, and so on.
Therefore, well water or river water must be filtered and softened
in softening water equipment before flowing into chilled water
system. If sand and clay settle in the evaporator, circulation of
chilled water may be blocked, and thus leading to freezing
accidents; if hardness of chilled water is too high, furring may
occur easily, and the devices may be corroded. Therefore, the
quality of chilled water should be analyzed before being used,
such as PH value, conductivity, concentration of chloride ion,
concentration of sulfide ion, and so on.
<50ppm
<50ppm
<30ppm
<200μV/cm(25℃)
<0.3ppm
<50ppm
<50ppm
4.8.2 Applicable standard of water quality for the unit
PH value
Total hardness
Conductivity
Sulfide ion
Chloride ion
Ammonia ion
Sulfate ion
Silicon
Iron content
Sodium ion
Calcium ion
No
No
No requirement
Table 4-2
7～8.5
4.9 Installation & regulation guide for target flow
controller
4.9.1 Please carefully check flow switches before conducting
installation of the target flow controller. Packing should be in
good condition, and the appearance should be free of damage
and deformation. If any problem, please contact the
manufacturer.
4.9.2 Flow switches can be installed in the horizontal pipeline or
the vertical pipeline with upward flowing direction but cannot be
mounted in the pipeline with downward flowing direction. The
inlet water of gravity should be taken into account when flow
switches are installed in the pipeline with upward flowing
direction.
4.9.3 Target flow controller must be installed on a section of
straight-line pipeline, and its both ends must be supplied with
straight-line pipes whose length is at least 5 times diameter of
the pipe. In the meanwhile, the fluid flowing direction in the
pipeline must be consistent with the direction of arrow on the
controller. The connection terminal should be located where
wiring connectioncan be easily done.
4.9.4 Pay attention to the following items when conducting
installation and wire connection:
a. Collision of the wrench with the soleplate of the flow switch is
prohibited, since such collision may cause deformation and
failure of the flow switch.
b. To avoid electric shock and damages to the devices, the
power supply should be cut off, when wires are connected or
adjustment is done.
c. When wiring connection is conducted, adjustment of other
screws except connection terminals of micro switches and
ground screws is prohibited. In the meanwhile, over great force
should not applied when wires of micro switches are connected,
otherwise micro switches may suffer displacement, thus leading
to failure of flow switches.
d. Special grounding screws should be used for earth
connection. Bolts should not be installed or removed at will;
otherwise flow switches may suffer deformation and failure.
e. Flow switches have been set at minimal flow value prior to
ex-factory. They should not be adjusted below the ex-factory
setting value, or they may suffer failure. After installing flow
switches, please press the flow switch lever several times to
check them. When the lever is found not to respond with
“clatter”, rotate the screw in a clockwise direction, until “clatter”
occurs.
f. Be sure to determine the model of target slice according to
the rated flow of the unit, the diameter of the outlet pipe and the
adjustment range of the target slice of the flow switch. Besides,
the target slice should not contact with other restrictors in the
pipeline or on the inner wall of the pipeline, or the flow switch
cannot be reset normally.
4.9.5 Determine whether the flow switch and the system
connected with it are in good operation according to the
measured value by flow meter, namely, when the measured
value on flow meter is less than 60% of rated water flow of the
unit, the target flow controller should be cut off and observed for
3 working periods, and it should be covered with flow switch
shell timely.
10
I&O manual

11
I&O manual
4.10 Installation of single-module water system pipeline
Fig. 4-5
SCV-300EA
Fig. 4-6
SCV-600EA
Water inlet
Water outlet
Total water outlet
temperature sensor
Electric control box
Electric control box
Water inlet
Water outlet
Total water outlet
temperature sensor

Table 4-3
4.11.2 Table of diameter parameters of main inlet and outlet pipes
I&O manual
12
CAUTION
Please pay attention to the following items when installing multiple modules:
●Each module corresponds to an address code which cannot be repeated.
●Main water outlet temperature sensing bulb, target flow controller and auxiliary electric heater are under control of the main module.
●One wired controller and one target flow controller are required and connected on the main module.
●The unit can be started up through the wired controller only after all addresses are set and the aforementioned items are determined. The
wired controller is ≤500m away from the outdoor unit.
25≤Q≤50
50＜Q≤80
80＜Q≤130
135＜Q≤210
210＜Q≤325
325＜Q≤510
510＜Q≤740
740＜Q≤960
DN40
DN50
DN65
DN80
DN100
DN125
DN150
DN200
4.11 Installation of multi-module water system pipeline
Multi-module combination installation involves special design of the unit, so relevant explanation is given as follows.
4.11.1 Installation mode of multi-module combination water system pipeline
1)
SCV-300EA,SCV-600EA
Fig.4-7 (installation mode A: less than 16 modules)
No.n module
No.(n-1) address
No.1 module
No.(n-1) module
No.(n-2) address No.0 address
Total inlet and outlet water
pipe inside nominal diameter
Cooling capacity
Pump
Drill dead hole at the
position, and move the
total effluent temperature
sensor at No.0 address to
the position

5. ELECTRIC WIRING
5.2 Power supply specification
Table 5-1
Outdoor power supply
Power
supply
Manual
switch Fuse Wiring
Item
Model
380-415V
3N~50Hz
50A 36A 10mm2
(<20m)
5.3 Requirements of wiring connection
5.3.1 No additional control components are required in the electric
cabinet (such as relay, and so on), and the power supply and
control wires not connected with the electric cabinet are not
allowed to go through the electric box. Otherwise, electromagnetic
interference may cause failure of the unit and control components
and even damages to them, which thus lead to protective failure.
5.3.2 All cables led to the electric box should be supported
independently but by the electric box.
5.3.3 The strong current wires generally pass the electric box, and
220-230V alternating current may also pass the control board, so
wiring connection should conform to the principle of separation of
strong current and weak current, and the wires of power supply
should be kept more than 100 mm away from the control wires.
5.3.4 Only use 380-415V 3N~50Hz rated power supply for the
unit, and the maximum allowable range of voltage is
342V~440V(for SCV-300EA) & 342V-356V (for SCV-600EA).
5.3.5 All electric wires must conform to local wiring connection
norm. The suitable cables should be connected to power supply
terminal through wiring connection holes at the bottom of the
electric cabinet. According to Chinese standard, the user is
responsible for providing voltage and current protection for the
input power supply of the unit.
5.3.6 All power supplies connected to the unit must pass one
manual switch, to ensure that the voltages on all nodes of
electric circuit of the unit are released when the switch is cut off.
5.3.7 The cables of correct specification must be used to supply
power for the unit. The unit should use independent power
supply, and the unit is not allowed to use the same power supply
together with other electric devices, to avoid over-load danger.
The fuse or manual switch of the power supply should be
compatible with working voltage and current of the unit. In case
of parallel connection of multiple modules, the requirements of
wiring connection mode and configuration parameters for the
unit are shown in the following figure.
5.3.8 Some connection ports in the electric box are switch
signals, for which the user needs to provide power, and the rated
voltage of the power should be 220-230VAC. The user must be
aware that all power supplies they provided should be obtained
through power circuit breakers (provided by the user), to ensure
that all voltages on the nodes of the provided power supply
circuit are released when the circuit breakers are cut off.
5.3.9 All inductive components provided by the user (such as
coils of contactor, relay, and so on) must be suppressed with
standard resistance-capacitance suppressors, to avoid
electromagnetic interference, thus leading to failure of the unit
and its controller and even damages to them.
5.3.10 All weak current wires led to the electric box must apply
shielded wires, which must be provided with grounding wires.
The shield wires and power supply wires should be laid
separately, to avoid electromagnetic interference.
5.3.11 The unit must be provided with grounding wires, which
are not allowed to be connected with the grounding wires of gas
fuel pipelines, water pipelines, lightning conductors or
telephones. Improper earth connection may cause electric
shock, so please check whether earth connection of the unit is
firm or not frequently.
Outdoor power supply
Outdoor
unit 1
Outdoor
unit 2
Outdoor
unit 3
Outdoor
unit 4
Outdoor
unit N
Manual switch
Manual switch
Manual switch
Manual switch
Manual switch
Only 16 Modular units can be combined at most.
NOTE
5.4 Wiring steps
Step 1. Check the unit and ensure that it is connected with
grounding wires correctly, to avoid leakage, and the grounding
devices should be mounted in strict accordance with the
requirements of electrical engineering rules. The grounding
wires can prevent electric shock.
Step 2. The control box of the main power switch must be
mounted in a proper position.
Step 3. Wiring connection holes of the main power should be
provided with glue cushion.
Step 4. The main power and neutral wires and grounding
wires of power supply are led into the electric box of the unit.
Fig. 5-1
I&O manual
13
5.1 Electric wiring
1. The air-conditioner should apply special power supply, whose
voltage should conform to rated voltage.
2. Wiring construction must be conducted by the professional
technicians according to the labeling on the circuit diagram.
3. The power wire and the grounding wire must be connected
the suitable terminals.
4. The power wire and the grounding wire must be fasten up by
suitable tools.
5. The terminals connected the power wire and the grounding
wire must be fully fastened and regularly checked, in case to
become flexible.
6. Only use the electric components specified by our company,
and require installation and technical services from the
manufacturer or authorized dealer. If wiring connection fails to
conform to electric installation norm, failure of the controller,
electronic shock, and so on may be caused.
7. The connected fixed wires must be equipped with full
switching-off devices with at least 3mm contact separation.
8. Set leakage protective devices according to the requirements
of national technical standard about electric equipment.
9. After completing all wiring construction, conduct careful check
before connecting the power supply.
10. Please carefully read the labels on the electric cabinet.
11. The user’s attempt to repair the controller is prohibited, since
improper repair may cause electric shock, damages to the
controller, and so on. If the user has any requirement of repair,
please contact the maintenance center.
12.The power cord type designation is H07RN-F.
CAUTION
S
380-415V
3N~50Hz
70A100A 25mm2
(<20m)
SCV-300EA
SCV-600EA

14
I&O manual
5.5 Electric control schematic diagram of the unit
5.5.1 Schematic diagram of connection and communication of the main unit and subordinate units (see Attached Picture)
5.5.2 Indicating diagram of electric control of main control board (see Fig.5-4)
Fig.5-4
The picture is for reference only, refer to the actual board.
An all-pole disconnection device which has at least 3mm separation distance in all pole and a residual current
device(RCD)with the rating of above 10 mA shall be incorporated in the fixed wiring according to the national rule.
The appliance shall be installed in accordance with national wiring regulationgs.
CAUTION
4
33
13
22
11 7
26
12
5
6
32 31
29
9
814
27
2
28
3
23
1
24
25
15
30
10
16
17
18
19
20
21
34
35
36
Step 5. The wires of the main power must pass the bonding clamp.
Step 6. Wires should be connected firmly to the connection terminals A, B, C and N.
Step 7. Phase sequences must be consistent when the wires of the main power.
Step 8. The main power should be located out of easy reach of non-professional maintenance personnel, to avoid mal-operation and
improve safety.
Step 9. Connection of control wires of auxiliary electric heaters: the control wires of AC contactor of the auxiliary electric heater must
pass the connection terminals CN19_L and CN19_N of the main unit, as shown in Fig. 5-2.
Step 10. Connection of control wires of pump: the control wires of AC contactor of pump must pass the connection terminals CN1 or
CN2 of the main unit, as shown in Fig. 5-3.
Step 11. The connection way of the wire controller connects with every signal wires from package units: signal wires P, Q, E are
connected in the same way of main wires connection method and accordingly connect to the terminals P, Q, E in the wire controller.
CN19_Ｌ
Fig.5-2
Power supply (220-240V~50Hz)
Overcurrent relay
Control coil of AC contactor
Fig.5-3
Power supply (220-240V~50Hz)
Overcurrent relay
Control coil of AC contactor
Switch (For trial run of pump)
CN19_N
CN2 or
CN1

15
I&O manual
5.6 Detail description for parts in fig. 5-4
1
2
3
4
5
6
Detail information
I1：Detection of current of the compressor A (protection code P4)
I2：Detection of current of the compressor B (protection code P5)
7
8
No.
Table 5-2
10
Outdoor fan , controlled by T4
One compressor of the system
Electronic expansion valve of the system
signal communication port (fault code E2)
T4: outdoor ambient temperature sensor (fault code E7)
T3 ：pipe temperature sensor of the condenser (fault code E5 and protection code P7)
1)T4: if there is one system that requires starting outdoor fans, the fans are started through electric control of
the unit. Start outdoor fan A only, start A and B gears, and control the unit through T4.
2)T3: when the electric control of the Modular unit detects the temperature of the outdoor pipe T3 of the system
exceeds the protective temperature 65℃the corresponding system will be shut down. And it will be re-started
up, after the temperature drops below the recovery temperature 60℃. Another system will be not affected.
3)T4, T3: when the temperature sensor is detected to suffer open circuit or short circuit, fault alarm will occur. When
the main unit suffer fault of temperature sensor: the main unit and subordinate units will be shut down.When the
subordinate unit suffer fault of temperature sensor: the unit will be shut down, but other subordinate units will not
be affected.
Taf1: Shell and tube low-temperature ant-freeze sensor1 (fault code 1 Eb)
TZ/7: Total cooling temperature test port
TP2:Compressor exhaust temperature detecting port of the systemB
TP1:Compressor exhaust temperature detecting port of the systemA
Th:Compressor back gas temperature detecting port
Taf2: Shell and tube low-temperature ant-freeze sensor 2 (fault code 2 Eb)
Two: Unit outlet water temperature sensor (fault code E4)
Under refrigeration mode and heating mode, conduct adjustment according to the magnitude of unit outlet water
temperature.
Adjustment range of constant speed capability: ON and OFF.
Twi: Inlet water temperature sensor (fault code EF)
Tw: Total outlet water temperature sensor (fault code E3)
Only the main unit is valid, and the subordinate units are invalid.
Under refrigerating mode and heating mode, conduct adjustment according to the magnitude of total outlet
watertemperature. Adjustment range: Load, stabilize, unload, Emergency Stop.
Low pressure sensor
Module temperature test port
Module temperature is higher than 82℃when shutdown protection PL
9
11 I1：Detection of current of the compressor A (protection code P4)
I2：Detection of current of the compressor B (protection code P5)
Low voltage protection switch12
13 high-pressure protection and discharge temperature switch protection (protection code P0)

16
I&O manual
14
15
16
17
18
Detail information
No.
19/20
21
22
23
24
25
CN58/CN59：Filter board power supply port
CN44：Remote control port
If the port is closed, it is the heating mode; if the port is disconnected, it is the cooling mode
CN44：Water flow detection (fault code of the main unit E9) is only valid for the main unit but invalid for subordinate units.
1) Main unit: if abnormal water flow occurs , the main unit board and the wired controller will display fault code E9.
2) Subordinate unit: (water flow detection will not be done).
CN21：The alarm signal output of the unit(ON/OFF signal)
CN19：Auxiliary electric heater
Attention: the control port value of auxiliary electric heater actually detected is ON/OFF but not 220-230V control
power supply, so special attention should be paid when installing the auxiliary electric heater. Attention!
Under heating mode, when the main unit board detects total water outlet temperature to be lower than 45℃，the
switch will be closed, and the auxiliary electric heater will begin to work; when the total water outlet temperature is
higher than 50℃，the switch will be opened, and the auxiliary electric heater will stop working.
CN2：Pump2 signal switch,functional equivalence CN1.
CN1：PUMP1
Attention: the control port value of the pump actually detected is ON/OFF but not 220-230V control power supply，so
special attention should be paid when installing the pump.
1）After receiving start-up instruction, the pump will be started up instantly, and will maintain start-up state always in the
process of operation.
2）In case of refrigerating or heating shutdown, the pump will be shut down 2 minutes after all modules stop operating.
3）In case of shutdown under the pump mode, the pump can be directly shut down.
CN30：Input of three-phase four-wire power supply (fault code E1)
Three phases A, B and C of power supply should exist simultaneously, and the difference of phase angle should be
120º among them. If the conditions are not met, fault of phase sequence or phase lack may occur, and fault code will
be displayed. When the power supply returns to normal condition, fault is removed. Attention: phase lace and phase
dislocation of power supply are detected only in the early period after the power supply is connected, and they are not
detected while the unit is in operation.
S5：1)The cooling water temperature of the conventional cooling water/ cooling water temperature selection (dial code S5-1)
host is valid,and the master slave machine needs a unified code.
2)Remote control function selection(dial code S5-4)host effective
3)Pump control units selection(dial code S5-3)
ENC2：Outdoor unit capacity code
ENC1：When the address is 0, it serves as the main unit
When the address is 1,2,3……F, it serves as the subordinate unit 1,2,3……15.
Each Modular part of Modular unit has the same electric control function, and the main unit and subordinate units can
be set through address code on the electric control board. The address code 0 #is provided as the main unit. The
priority of being the main unit is given to the unit with digital
compressor, and other addresses are subordinate units. Only the unit is chosen as the main unit, its electric control
can activate such functions asdirect communication with the wired controller, refrigerating and heating capability
adjustment, pump control, auxiliary electric heater control, total effluent temperature detection and water flowswitch
detection.
26
CN44：Remote control port(ON/OFF signal,effect on NO.0 unit)