SeaLand VACUFLUSH 500 Plus Series User manual

1
SEALAND®
FINE CHINA TOILET
OWNER’S MANUAL
Traveler®500 Plus Series, 2000 Series,
Traveler Lite®100 Series Toilets
Dometic Corporation
13128 State Rt. 226, P.O. Box 38
Big Prairie, OH 44611-0038 USA
SeaLand Product Hotline [phone]
(8:00 a.m. - 5:00 p.m. ET)
This manual must be read and under-
stood before installation, adjustment,
service, or maintenance is performed.
Modification of this product can
result in property damage.
WARNING
!

2

3
1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain opening types, in the system. These
products damage the seals in toilets and dump valves.
2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be flushed through
the toilet.
3. Mechanical seal toilets, like SeaLand Traveler units, are designed to only discharge directly into a holding
tank. Horizontal pipe runs as found in conventional residential or commercial plumbing systems cannot be
accommodated.
4. Toilet bowl and flush seals must be regularly cleaned and winterized according to “Proper Cleaning and
Maintenance” and “Winterizing” procedures on page 5, or your warranty coverage may be voided.
IMPORTANT INFORMATION
TABLE OF CONTENTS
To prepare the Traveler toilet for use, check to be sure water supply to the toilet is connected. Turn on water supply and
check system for leaks. Flush toilet and check for leaks.
To properly use the Traveler toilet, follow these simple instructions:
1. To add water to the toilet, lift or raise the flush lever until desired water level is reached.
Generally, more water is required only when flushing solids.
2. To flush toilet, push lever all the way down until contents leave toilet bowl. Water flow pressures vary at
different locations, therefore holding the flush lever down for 4-8 seconds may be required. We require a
minimum flow to the toilet of two gpm (7.6 lpm) for proper rim and bowl wash.
3. Release flush lever by allowing it to snap back, which permits positive sealing around the flush ball.
4. A small amount of water should remain in bowl.
Note: Holding flush lever down longer than necessary results in excessive water usage.
HOW TO USE
Important Information .............................................. 3
Toilet Model Identification ....................................... 3
How to Use ............................................................ 3
Installation.............................................................. 4
Pedestal and Pedal Cover Installation..................... 4
Proper Cleaning and Maintenance .......................... 5
Winterizing ............................................................. 5
Deodorants and Special Tissue .............................. 6
Service Tip ............................................................. 6
Troubleshooting Guide ....................................... 7 - 9
100 Series Parts List ........................................... 10
500 Plus Series Parts List .................................... 11
2000 Series Parts List .......................................... 12
Dimensional Specifications ................................... 13
Ordering Parts ...................................................... 14
Parts Distributors ................................................. 14
Manufacturer’s Limited Warranties ....................... 16
The model identification label is located on the toilet base
and will show the model number and serial number. Follow
instructions for removing toilet pedestal cover in “Pedestal
and Pedal Cover Installation” on page 4. Traveler Lite Model
110 identification label is on the back of the base. If label is
not available, please refer to “Dimensional Specifications”
on page 13 for toilet model identification.
TOILET MODEL IDENTIFICATION
DOMETIC CORPORATION
P.O. BOX 38, 13128 STATE RT 226 [phone]
BIG PRAIRIE, OH 44611 USA
MODEL NO. 000
SERIAL NUMBER
000000

4
1. To replace an older toilet, turn off water supply to toilet.
Disconnect water line at toilet water valve. Unscrew floor bolt
nuts and remove toilet. Discard old floor seal and mounting
bolts. The old floor flange may be used if it is in good
condition and has four (4) bolt locations. [Only two bolts are
required for Traveler Lite Model 110.]
NOTE: If old floor flange cannot be used and cannot be
removed, please use a SeaLand Universal Mounting Kit,
available from your SeaLand dealer.
2. When installing new floor flange, make certain that the toilet
mounting bolts align properly with Traveler toilet mounting
pattern.
3. Secure flange to floor using flat head screws through
countersunk holes in flange. Insert floor bolts into slotted holes
in flange (Figure A).
4. If toilet is being installed in a shower stall, apply a 1/4" thick
by 3/4" wide bead of glazing compound around the circumfer-
ence of the floor flange (Figure B).
5. Install seat assembly with hinges and screws provided.
Traveler Models 510/511 will also accept handicap or house-
hold decorative seats. [Traveler Lite Models 110/111 seats
are already installed.]
6. Position floor seal by pressing the floor bolts up through holes
in the seal.
7. Set toilet in place with bolts protruding up through mounting
holes in base (Figure C).
8. Install washers and hex nuts provided with toilet. Snug nuts
down equally with standard 7/16" open end wrench. Remove
excess glazing compound from around base in shower stall
installation. For Traveler Lite Model 110, also install two wood
screws provided in two holes at rear of base. (See Figure C).
9. Connect water supply line to water valve (1/2" MPT) inlet
using appropriate fittings or an extension (Figure D). For
Traveler Lite Model 110, you must remove water valve cover
from flush pedal before connecting water supply line (see instructions below).
10. Turn on water supply and flush toilet to test for leaks.
11. For all models except Traveler Lite Model 110, attach pedestal and pedal covers to toilet base (see installation
instructions below).
PEDESTAL AND PEDAL COVER INSTALLATION
Fig. B
Fig. C
Fig. D
Fig. A
All Traveler toilets
and Traveler Lite
Model 111
(4-bolt connection)
Traveler Lite
Model 110
(2-bolt connection)
Insert
two
wood
screws
in rear
of base.
INSTALLATION
2. Tall model – screw
cover together. Short
model – snap together.
1. Wrap pedestal cover
around base so that it
closes as shown.
3. Slide pedal cover onto
foot pedal rod.
4. Secure side plate onto
pedal cover with screws.
ALL TRAVELER TOILETS AND TRAVELER LITE MODEL 111:
TRAVELER LITE MODEL 110:
1. Press button on back of
pedal to release water
valve cover.
2. Pull on bottom of cover
to remove it. Cover
snaps back into place.

5
WINTERIZING
At the end of each season, the Traveler or Traveler Lite toilet should be winterized
for storage, by either draining or using potable water-safe antifreeze in the system.
To drain:
1. Thoroughly flush system with fresh water.
2. Empty holding tank.
3. Shut off water supply to toilet(s), and remove inlet waterline (Fig. C).
Do not remove brass cap on bottom of valve.
4. Press flush lever until all water is drained from toilet(s).
To use antifreeze:
1. Drain potable water tank.
2. Add freshwater antifreeze to potable water tank.
3. Flush potable water antifreeze and water mixture through toilet(s) and into the waste holding tank. Each
installation is different, so amounts may vary. User discretion is required to assure adequate protection.
4. Empty holding tank.
NOTE: Use nontoxic antifreeze designated for potable water systems. (See vehicle owner’s manual.)
CAUTION: Never use automotive-type antifreeze in freshwater systems.
Fig. C
The Traveler toilet should be cleaned regularly for maximum sanitation and opera-
tional efficiency. You can clean it just as you would a household toilet. Do not use
caustic chemicals, such as drain-opening types, as they will damage
the seals.
BOWL CLEANING: For stubborn stains, use SeaLand®Bowl and Seal Cleaner
(Fig. A). It’s manufactured especially for use with Traveler and Traveler Lite toilets.
In certain locations where water is hard, a build-up of lime may dull the toilet bowl
finish. Restore the shine with this SeaLand cleaner. If you cannot find it in your
area, contact SeaLand for your nearest dealer. If the cleaner is not available, you
can also use Bar Keepers Friend®cleanser. It is not necessary to vigorously scrub
with either product. Please follow label instructions.
SEAL CLEANING: After an extended time, mineral deposits from hard water can
build up under the edge of the rubber bowl seal, resulting in a slow leakdown of
water from the bowl. To prevent this mineral build-up, periodically clean under the
bowl seal with SeaLand Bowl and Seal Cleaner (Fig. B).
1. Shut off water supply.
2. Apply cleaner onto the seal cleaning tool (supplied with new toilet), open the
flush ball by pressing on flush lever, and scrub under the seal. Make sure to
push bristles between bottom of seal and top of flush ball surface to scrub all
parts of seal that come into contact with flush ball.
3. Close ball and wait 2-3 minutes.
4. Open flush ball. Use brush and water to rinse away cleanser and loosened deposits.
PROPER CLEANING AND MAINTENANCE
Fig. A
Fig. B

6
SERVICE TIP
Checking for water leaks behind or under toilets or other appliances can make it difficult to locate the source. Dripping
water at room temperature makes it difficult to feel wetness. Taking four or five sheets of toilet tissue and wiping all
seams and waterline connections offers a simple means of locating the general area of the leakage. Start at the top of
the unit since gravity will cause a leak to run downward. When the tissue comes in contact with the leaking water, it will
immediately change texture.
DEODORANTS AND SPECIAL TISSUE
Your Traveler toilet requires the regular addition of a deodorant product to reduce malodors and to help break down
holding tank contents. Several factors should be considered in selecting a deodorant product.
Liquid or Granulated: Liquid products obviously work more quickly by readily going into solution. Granulated powder
formulations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the
package is inadvertently damaged.
Formaldehyde versus Non-Formaldehyde: Dometic manufactures both types of deodorants. Generally speaking,
formaldehyde formulas control odor very effectively at all temperatures and with all degrees of water hardness. SeaLand
Environment-Friendly brand, which is formaldehyde free, is similarly effective.
How Much Deodorant and How to Add It: The deodorant is added directly into the toilet bowl, then flushed into the
holding tank. Follow bottle or package instructions. Conditions of extremely warm weather, longer waste holding time
and larger tank capacities may require more deodorant treatment. Also, to maintain optimum efficiency in odor control,
the waste holding tank should be cleaned thoroughly at least once or more each season depending on use.
Why Not Use Household Toilet Paper in Your Traveler Toilet. Household tissues often contain adhesives which
bond together the paper fibers from which the tissue is made. The adhesives prevent the tissue from breaking apart,
and their use in “ultra-low flow” systems can cause system clogging. SeaLand tissue is especially designed for use in
low water toilet systems. Its rapid dissolving properties minimize the amount of residual paper in the holding tank and
allow deodorizers to work more efficiently.
SeaLand Brand versus Other Brands: We constantly strive to provide our system owners with effective products
that have minimal environmental impact and good value. Many deodorant products do not measure up to our standards
of performance and value.
SeaLand®Granulated
Deodorant
Six 2-oz. pouches
Part No.
379626002
SeaLand®Liquid
Deodorant
Two 8-oz. bottles
Part No.
379224008
SeaLand®
Cleaner
16-oz. bottle
Part No.
379314016
SeaLand®Liquid
Deodorant -
Environment Friendly
32-oz. bottle
Part No.
379114032
SeaLand®
Rapid-Dissolving
Toilet Tissue
Four 400-sheet rolls
Part No. 379441204

7
TROUBLESHOOTING GUIDE
TRAVELER TOILET
BASE ASSEMBLY
(except model 110)
ADJUSTING NUT
SPRING
CARTRIDGE
WATER VALVE ASSEMBLY
TOP VALVE CAP
FILTER SCREEN
WATER VALVE SCREWS
VALVE BODY
SHAFT
PEDAL
COVER
BAND CLAMP
BALL SEAL
FLUSH BALL
CAM STRAP
TRAVELER LITE MODEL 110
BASE ASSEMBLY
ADJUSTING NUT
FLUSH BALL
SPRING
CARTRIDGE
WATER VALVE ASSEMBLY
TOP VALVE CAP
FILTER SCREEN
WATER
VALVE
SCREWS
VALVE BODY
SHAFT
FLUSH PEDAL
PEDAL
COVER
BAND CLAMP
BALL SEAL
BOWL SEAL
BOWL SEAL
TRAVELER LITE TOILET BOWL, REAR VIEW
(Models 110, 111)
TRAVELER TOILET BOWL, REAR VIEW
(Models 510+, 511+, 2010, 2011)
VACUUM
BREAKER
WHITE CAP
HOSE
CONNECTION
VACUUM BREAKER/BOWL CONNECTION
VACUUM
BREAKER
HOSE
CONNECTION
VACUUM BREAKER/BOWL CONNECTION

8
TROUBLESHOOTING GUIDE (cont'd)
1. Toilet emits odor (flush ball
open).
2. Water will not stay in bowl.
3. Flush ball will not close
completely.
4. Flush ball will not open.
5. Flush ball does not open
completely. Applies to
short-base units mounted
on step or riser only.
6. Water does not shut off in
toilet (toilet overflows).
7. Hand spray unit leaks.
8. Water does not enter toilet
bowl properly.
a. Odor emitting from base of toilet.
b. Plugged holding tank vent line.
a. Loose band clamp.
b. Improper seal around flush ball
due to dirt or debris on underside
of ball seal.
c. Worn or damaged seal.
d. Worn or damaged flush ball.
a. Too much friction between flush
ball and ball seal.
b. Water valve screws are too tight.
c. Defective spring cartridge.
a. Broken shaft.
b. Shaft not fully engaged in the
spring cartridge.
a. Floor flange interferes with flush ball
rotation.
a. Not enough clearance between
cam strap and top of water valve
cap.
b. Dirt lodged in water valve seal.
c. Worn or defective water valve.
d. Worn or defective spring cartridge.
a. Hand sprayer is defective.
a. Insufficient water flow rate at toilet.
b. Water valve clogged.
c. Plugged rim wash holes in toilet.
a. Use SeaLand brand deodorants.
b. Clear obstruction from vent line.
a. Tighten adjusting screw.
b. Inspect flush ball and underside
of seal for foreign objects. Clean
under seal if needed (see page 5.
Cleaning tool available – part no.
600344236).
c. Replace seal.
d. Replace flush ball.
a. Lubricate between flush ball and
ball seal with furniture polish or
cooking spray.
b. Loosen screws slightly.
c. Check spring tension by pushing
flush lever down, then release it
suddenly. If lever does not snap
back to original position, replace
spring cartridge.
a. Replace shaft.
b. Put pressure on shaft from under
the flush ball (pushing into spring
cartridge) until it engages. You
may have to rotate flush ball
slightly until shaft lines up with
square in spring cartridge.
a. Loosen mounting bolts and push
toilet base back. If this does not
solve problem, install a SeaLand
Universal Mounting Kit (part no.
310139, 310140, or 310141) with
existing floor flange.
a. Adjust cam strap to have .02" -
.06" (.5mm - 1.5mm) clearance
with top of water valve cap. (Does
not apply to model 110.)
b. Dissassemble and clean water
valve.
c. Replace water valve.
d. Replace spring cartridge.
a. Replace hand sprayer.
a. Check water flow rate at toilet.
Rate should be 2 gpm (7.6 lpm) at
toilet.
b. Remove and clean screen located
at inlet of water valve.
c. Clean holes. If still a problem,
replace the toilet bowl.
Problem Possible Cause Service Instructions

9
TROUBLESHOOTING GUIDE (cont'd)
Problem Possible Cause Service Instructions
9. Water is leaking from
water valve.
10. Water is leaking from
bottom of toilet base.
11. Water is leaking from rear
of toilet bowl.
12. Water is leaking from the
base/toilet connection.
a. Water valve body cracked due to
freeze damage.
b. Water line connection is loose or
not seated properly.
c. Defective water valve.
d. Stripped threads.
a. Toilet is not secured to floor.
b. Worn or defective toilet mounting
floor seal.
c. Cracked base.
d. Worn or defective floor flange.
a. Worn or defective vacuum breaker.
b. Loose vacuum breaker.
c. Cracked or defective toilet bowl.
a. Band clamp may be loose.
b. Ball and bowl seals may be worn
or defective.
a. Replace water valve.
b. Insure that threads are not cross-
threaded and tighten.
c. Replace water valve.
d. Replace water valve.
a. Tighten toilet mounting bolts.
b. Replace floor seal between floor
flange and toilet base.
c. Replace base assembly.
d. Replace floor flange.
a. Remove white cap from vacuum
breaker. Flush toilet. If water
leaks during flush, vacuum
breaker needs to be replaced.
b. Secure vacuum breaker
connection.
c. Replace toilet bowl. If loose, push
breaker into bowl.
a. Remove plastic base cover (on
applicable models) and tighten
the band clamp.
b. Replace ball and bowl seals.

10
TRAVELER LITE®PARTS LIST
MODEL 111 MODEL 110
1
2
3
4
5
6
7
8
Item
SeatAssembly, White
Seat Assembly, Bone
China Bowl Kit, White
China Bowl Kit, Bone
Band Clamp & Half Clamp Kit, White
Band Clamp & Half Clamp Kit, Bone
Teflon®& Rubber Seal Kit
Base Kit, White (includes 3, 4, 6,
7, 9, 10A, 11, 12)
Base Kit, Bone (includes 3, 4, 6,
7, 9, 10A, 11, 12)
Base Kit, White (includes 3, 4, 6,
7, 9, 10, 11, 12, 13, 17)
Base Kit, Bone (includes 3, 4, 6,
7, 9, 10, 11, 12, 13, 17)
Ball, Shaft & Cartridge Kit
Floor Flange Seal
Floor Flange Adapter, 3" MPT
(sold separately)
Floor Flange Adapter, 3" Socket
(sold separately)
Floor Flange Adapter, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º Swivel
(sold separately)
385344088
385344089
385310790
385310791
385310048
385316140
385310801
385310802
385318162
600341549
385345889
385345892
385343765
307344653
385344088
385344089
385310790
385310791
385310025
385310048
385316140
385310792
385310793
385310681
600343938
385345889
385345892
385343765
307344653
9
10
10A
11
12
13
14
15
15A
15B
15C
16
17
385310064
385310117
385310118
385314349
385236096
600340825
600340177
385310687
385319054
600340683
385230335
385310795
385310796
385310108
385310109
385310794
385310803
385310682
385310762
385314349
385310683
600340177
385310687
385319054
600340683
385230335
385310795
385310796
Floor Bolt Mounting Kit
Floor Bolt Mounting Kit, White
Floor Bolt Mounting Kit, Bone
Pedal Cover Kit, White
Pedal Cover Kit, Bone
Flush Pedal Kit, White (incl. 12)
Flush Pedal Kit, Bone (incl. 12)
Water Valve Kit
Spring Cartridge Kit
Flush Lever
Supply Hose, Bone
Vacuum Breaker Kit
Vacuum Breaker Kit w/ Spray
Hand Spray, White
Vacuum Breaker (used w/ Spray)
Vacuum Breaker Cover Kit, White
Vacuum Breaker Cover Kit, Bone
Pedestal Cover Kit, White
Pedestal Cover Kit, Bone
Description
111 110 Item Description111 110

11
500 PLUS SERIES PARTS LIST
MODEL 511+ MODEL 510+
1
2
3
4
5
6
7
8
Item
SeatAssembly, White
Seat Assembly, Bone
Seat Assembly, Platinum
Seat Assembly, Ebony
Seat Assembly, Teal
China Bowl Kit, White
China Bowl Kit, Bone
China Bowl Kit, Platinum
China Bowl Kit, Ebony
China Bowl Kit, Teal
Band Clamp & Half Clamp Kit
Teflon®& Rubber Seal Kit
Mounting Bolt Kit
Pedestal Cover Kit, White
Pedestal Cover Kit, Bone
Pedestal Cover Kit, Platinum
Pedestal Cover Kit, Ebony
Pedestal Cover Kit, Teal
Floor Flange Seal
Floor Flange, 3" MPT
(sold separately)
Floor Flange, 3" Socket
(sold separately)
Floor Flange, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º
Swivel (sold separately)
385343829
385343831
385343897
385343901
385343899
385310739
385310740
385310741
385310742
385310743
385310048
385316140
385310064
385310108
385310109
385310110
385310600
385310603
600341549
385345889
385345892
385343765
307344653
385343829
385343831
385343897
385343901
385343899
385310739
385310740
385310741
385310742
385310743
385310048
385316140
385310064
385310111
385310112
385310113
385310173
385310203
600341549
385345889
385345892
385343765
307344653
9
10
11
12
13
14*
15
16
16A
17
18
385318162
385310177
385310188
385310117
385310118
385310119
385310593
385310596
385314349
385236096
600340825
385310744
385310123
385310124
385310125
385310588
385310620
600340177
385316906
385230335
385319054
600340683
600341770
385318162
385310177
385310188
385310114
385310115
385310116
385310175
385310193
385314349
385236096
600340873
385310578
385310120
385310121
385310122
385310169
385310198
600340177
385316906
385230335
385319054
600340683
600341770
Ball/Shaft/Cartridge Kit,
White/Bone/Platinum
Ball/Shaft/Cartridge Kit, Ebony
Ball/Shaft/Cartridge Kit, Teal
Pedal Cover Kit, White
Pedal Cover Kit, Bone
Pedal Cover Kit, Platinum
Pedal Cover Kit, Ebony
Pedal Cover Kit, Teal
Water Valve Kit
Spring Cartridge Assembly
Flush Lever
Flush Lever/Spring Cartridge Ass’y.
Base Kit, White
Base Kit, Bone
Base Kit, Platinum
Base Kit, Ebony
Base Kit, Teal
Supply Hose
Vacuum Breaker Kit
Vacuum Breaker Kit (used with
Hand Spray)
Vacuum Breaker w/ Hand Spray Kit
Hand Spray, White
Hand Spray, Ebony
Description
511+ 510+ Item Description511+ 510+
* includes items
3 – 7, 9 – 13

12
2000 SERIES PARTS LIST
MODEL 2011 MODEL 2010
1
2
3
3A
3B
3C
4
5
6
7
8
9
Item
Seat Assembly, White
Seat Assembly, Bone
Seat Assembly, Ebony
China Bowl Kit, White
China Bowl Kit, Bone
China Bowl Kit, Ebony
Vacuum Breaker Kit
Vacuum Breaker with Spray Kit
Hand Spray, White
Hand Spray, Ebony
Vacuum Breaker (used with
Hand Spray)
Supply Hose, Bone
Band Clamp & Half Clamp Kit
Teflon®& Rubber Seal Kit
Ball/Shaft/Cartridge Kit,
White/Bone
Ball/Shaft/Cartridge Kit, Ebony
Spring Cartridge Assembly
Pedal Cover Kit, White
Pedal Cover Kit, Bone
Pedal Cover Kit, Ebony
385344436
385344437
385344438
385310615
385310616
385310585
385316906
385319054
600340683
600341770
385230335
600340177
385310048
385316140
385318162
385310177
385236096
385310117
385310118
385310593
385344436
385344437
385344438
385310615
385310616
385310585
385316906
385319054
600340683
600341770
385230335
600340177
385310048
385316140
385318162
385310177
385236096
385310114
385310115
385310175
10
11
12 *
13
14
15
16
385314349
600340825
385310579
385310123
385310124
385310588
385310108
385310109
385310600
600341549
385310064
385345889
385345892
385343765
307344653
385314349
600340873
385310578
385310120
385310121
385310169
385310111
385310112
385310173
600341549
385310064
385345889
385345892
385343765
307344653
Water Valve Kit
Flush Lever
Flush Lever & Spring Cartridge Kit
Base Kit, White
Base Kit, Bone
Base Kit, Ebony
Pedestal Cover Kit, White
Pedestal Cover Kit, Bone
Pedestal Cover Kit, Ebony
Floor Flange Seal
Mounting Bolt Kit
Floor Flange, 3" MPT
(sold separately)
Floor Flange, 3" Socket
(sold separately)
Floor Flange, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º Swivel
(sold separately)
Description
2011 2010 Item Description 2011 2010
* includes items
5 – 11, 13 – 15

13
DIMENSIONAL SPECIFICATIONS
All dimensions may vary ± 3/8-inch (10mm).
MODEL 2011
*
* Width measurement includes flush pedal.
MODEL 2010
MODEL 510+
MODEL 110
MODEL 511+
*
* Width measurement includes flush pedal.
MODEL 111
*
* Width measurement includes flush pedal.

14
ORDERING PARTS
Dometic is ready to assist you in the event service is required. Before calling, please have the following information
available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs.
1. Toilet Model Number
2. Serial Number
3. Part Number, Description and Quantity (see Parts List)
CUSTOMER SERVICE
There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the
Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET) Monday through Friday.
Telephone: [phone] U.S.A. and Canada
330-496-3211 International
Email: [email protected]
Fax: [phone] U.S.A. and Canada
330-496-3220 International
U.S.A. – North Central
(IL, IN, KY, MI, OH)
Midwest Marine Supply
24300 Jefferson Ave.
St. Clair Shores, MI 48080
Tel: [phone]
800-860-1540
Fax: [phone]
Email: [email protected]
Contact: Bob Kennedy
U.S.A. - Northeast
(CT, DE, DC, MA, MD, ME, NH,
NJ, NY, PA, RI, VA, VT, WV)
Northeast Marine Sanitation
69 Florida Street
Farmingdale, NY 11735
Tel: [phone]
800-352-4323
Fax: [phone]
888-283-7606
E-mail: northeast@
northeastsanitation.com
Contact: Mike Starito
U.S.A. - Northwest
(AK, ID, MT, OR, WA, WY)
Marine Sanitation, Inc.
1900 N. Northlake Way, Suite 121
Seattle, WA 98103
Tel: [phone]
800-624-9111
Fax: [phone]
E-mail: marinesan@
mindspring.com
Contact: Ric Kolb
U.S.A. - South Central
(AR, KS, LA, MO, MS, NM, OK, TX)
AER Supply
P.O. Box 349
2301 Nasa Road #1
Seabrook, TX 77586
Tel: [phone]
800-767-7606
Fax: [phone]
E-mail: [e-mail]
Contact: Richard Miller
U.S.A. - Southeast
(AL, FL, GA, NC, PR, SC, TN, VI)
Environmental Marine Service
111 S.W. 23rd Street, SuiteA
Fort Lauderdale, FL 33315
Tel: [phone]
800-522-2656
Fax: [phone]
E-mail:
[email protected]
Contact: John or Jill Hopkins
U.S.A. - Southwest
(AZ, CO, NV, UT, CA-south)
Ardemco Marine Specialties
778 West 17th Street
Costa Mesa, CA 92627
Tel: [phone]
800-253-0115
Fax: [phone]
E-mail: [email protected]
Contact: Rick Glasser
CANADA DISTRIBUTORS
Canada – East
Eastern Marine Systems, Inc.
12-A Leslie Street
Toronto, Ontario M4M 3H7
Tel: [phone]
888-764-1111
Fax: [phone]
E-mail: [e-mail]
Contact: Paul Gales
Canada – West
Western Marine Company
1494 Powell Street
Vancouver, BC V5L 5B5
Tel: [phone]
800-663-0600
Fax: [phone]
800-663-6790
E-mail: [email protected]
Contact: Bill Falk
U.S.A. SEALAND MASTER SANITATION DISTRIBUTORS
U.S.A. – Upper Midwest
(IA, MN, ND, NE, SD, WI)
PowerHouse Marine
518 Logan
La Crosse, WI 54603
Tel: [phone]
888-752-4539
Fax: [phone]
E-mail:
[email protected]
Contact: Dave Tucker
U.S.A. – Northern California
Fox Marine
2250 Zanker Road, Unit D
San Jose, CA 95131
Tel: [phone]
800-826-2873
E-mail: [email protected]
Contact: Charlie Barker
You can also contact the Parts Distributor in your area for quick response to your replacement parts needs. They carry
a complete parts inventory for this SeaLand product line.

15
NOTES

16
Dometic Corporation warrants, to the original purchaser only, that this Traveler®gravity discharge toilet, if used for
personal, family or household-like purposes, is free from defects in material and workmanship for a period of three (3)
years from the date of purchase.
Dometic also warrants, to the original purchaser only, that the ceramic portion of the toilet bowl will not discolor, stain,
scratch or craze for a period of ten (10) years if used for personal, family or household-like purposes, and is regularly
cleaned as described in the product’s owner’s manual.
If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to be
free of defects in material and workmanship for a period of ninety (90) days from the date of purchase.
Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to be
defective in material or workmanship. All labor and transportation costs or charges incidental to warranty service are to
be borne by the purchaser-user.
EXCLUSIONS
IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGES
RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE, ALTER-
ATION, OR USE OF UNAUTHORIZED COMPONENTS. THIS INCLUDES FAILURES WHICH MAY RESULT FROM
NOT FOLLOWING THE WINTERIZATION OR CLEANING PROCEDURES AS DESCRIBED ON PAGE 5 OF THIS
OWNER’S MANUAL. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM DATE OF
PURCHASE.
IMPLIED WARRANTIES
No person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase for products used for personal, family or household-like purposes, and ninety (90) days from the
date of purchase for products placed in commercial or business use.
OTHER RIGHTS
Some states do not allow limitations on the duration of an implied warranty, and some states do not allow exclusions
or limitations regarding incidental or consequential damages; so, the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may have other rights which vary from state to state.
To obtain warranty service, first contact your local dealer from whom you purchased this product.
MANUFACTURER’S THREE-YEAR AND TEN-YEAR LIMITED WARRANTIES
® Registered; ™ Trademark of Dometic Corporation
® Bar Keepers Friend is a trademark of Servaas Laboratories.
® Teflon is a registered trademark of Du Pont Co.
 Dometic Corporation
340098 8/03
Dometic Corporation
13128 State Rt. 226, P.O. Box 38
Big Prairie, OH 44611-0038 USA
SeaLand Product Hotline [phone]
(8:00 a.m. - 5:00 p.m. ET)