Sealey LED109C User manual

INSTRUCTION MANUAL FOR:
CORDLESS 30SMD LED RECHARGEABLE
PORTABLE FLOODLIGHT LITHIUM-ION
MODEL NO : LED109C
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version LED109C Issue: 1 - 15/4/13
© Jack Sealey Limited
1. SAFETY
1.1. GENERAL
 WARNING! Disconnect floodlight from mains power before
performing any maintenance.
 DO NOT shine floodlight directly into your, other person’s or animal’s
eyes.
 DO NOT allow children to use the floodlight.
Maintain the floodlight in good condition.
 DO NOT use the floodlight if it is damaged.
 When not in use store the floodlight in a safe, dry, childproof
location.
 DO NOT use the floodlight without the front glass shield. Avoid
touching the front glass shield as handling may reduce its
serviceable life.
 DO NOT use the floodlight without the weather seals intact.
 DO NOT use the floodlight near flammable, combustable or
explosive liquids, soilds, gases or equipment.
 Maintain the floodlight in good condition. Repairs must only be
undertaken by a qualified electrician (use an authorised service
agent.)
 Keep a minimun distance of 1 metre from the front of the floodlight to
the surface which is to be illuminated.
 Locate the floodlight in an adequate area for its function, keep the
area clean and tidy and free from unrelated materials.
 DO NOT install the floodlight where it is likely to be knocked or hit.
 WARNING! Ensure Health and Safety, local authority and general
workshop practice regulations are adhered to when using this
floodlight.
1.2. ELECTRICAL SAFETY FOR USE OF
TRANSFORMER. USE ONLY THE SUPPLIED
TRANSFORMER PLUG FOR CONNECTING LAMP TO THE POWER
SUPPLY.
 WARNING! It is the user’s responsibility to read, understand and
comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installa-
tion of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is used with all
electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an RCCB.
You must also read and understand the following instructions
concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical
appliances, if used on business
premises, to be tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of
electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about
electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the transformer plug, cable and connector for wear and
damage to ensure items are safe before connecting to the mains
power supply. If worn or damaged DO NOT use.
Important: Check that the voltage marked on the transformer plug
is the same as the power supply to be used.
Uncoil the cable between transformer plug and lamp.
 DO NOT pull the transformer plug from the mains socket by the
lead.
 DO NOT use any other type of transformer with this product.
 DO NOT try to take the transformer plug apart.
 DO NOT use the transformer plug to power any other electrical item.
 DO NOT get the transformer plug wet, or use in wet, damp
conditions (for indoor use only).
 WARNING! NEVER substitute a standard 13amp 3 pin plug, or any
other type of plug, for the transformer plug.
This transformer plug reduces and rectifies the mains voltage
(230 volts AC) to 12 volts DC.

Battery Removal
Remove the five screws which hold on the glass lens. Pull the SMD unit forward and undo the two screws which hold
the battery cover on. Cut the battery wires and remove. Dispose of battery according to local government guidelines.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version LED109C Issue: 1 - 15/4/13
4.1. Keep oodlight clean and check for damage before every use. If damage is observed, remove from use until it is repaired.
4.2. Before the unit is disposed of at the end of its life , it is a requirement that the battery is removed. Refer to the battery removal section below.
4. MAINTENANCE
3. OPERATION INSTRUCTIONS
3.1. CHARGING
3.1.1. The charging port is at the back of the floodlight behind a rubber flap. A red light above the SMD LEDs denotes charging mode.
3.2. OPERATION
3.2.1. Position the floodlight in the area which requires illumination.
3.2.2. This LED floodlight develops minimal heat and is not subject to the same restrictions that apply to halogen lamps that become too hot to
touch. We do however recommend that the floodlight should not be placed in cramped or restrictive situations and recommend the
following minimum distances between the floodlight and any surface/object:
• 500mm minimum between the top of the floodlight and any overhead objects.
• 200mm between sides of floodlight and end or side walls, surfaces or objects.
• 1 metre minimum between the front of the floodlight and any object to be illuminated.
3.2.3. To turn the light on press the rocker switch on the back of the floodlight.
3.2.4. To adjust the angle of the floodlight loosen thumb screws on either side and retighten afterwards.
Portable floodlight with adjustable head, housed within a stable steel frame. Features 30 super bright SMD LEDs giving a full 120° spread of light.
Weatherproof design with on/off rocker switch. Supplied with mains cable. Built in 7.4V 3.0Ah Li-ion rechargeable battery. Suitable for lighting
workshops, garages and other environments where no mains supply is available.
Model No: ..................................................................................... LED109C
Battery:.................................................................... 7.4V 3.0Ah Lithium-ion
Lumen Output:................................................................................. 1200lm
LED: .............................................................................................30 SMD
Operating Time:...................................................................................3.5hr
Approximate Charging Time: ................................................................6hr
2. INTRODUCTION
© Jack Sealey Limited
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which must be applied by the operator.
Parts support is available for this product. To obtain a listing and/or diagram, please log on to: www.sealey.co.uk,
email: [e-mail] or phone: [phone]