Sealey LED130T User manual

1.1. PLUG & MAINS POWER SUPPLY
 WARNING! It is the owner’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure that they are safe before using. You must inspect power supply leads, plugs and all
electrical connections for wear and damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)
is used with all electrical products. It is particularly important to use an RCD together with portable products that are plugged into an electrical supply not
protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must
also read and understand the following instructions concerning electrical safety. NOTE: 110 volt lights are usually operated by connecting to a transformer or
a generator. Check to ensure all supply equipment is compatible with the rating of the light.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a
qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage and especially
power connections to ensure that none is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be used
and check that plugs are fitted with the correct capacity fuse.
A 13amp plug may require a fuse smaller than 13amps for certain products, see fuse rating listed right (fig.1).
1.1.7. Important: For use of a 110 volt lights - ensure that the transformer or generator is adequately rated.
1.1.8. DO NOT pull or carry the appliance by the power cable.
1.1.9. DO NOT pull plugs from sockets by the power cable.
1.1.10. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by a qualified
electrician. A U.K. 3 pin 13amp or 110 volt plug with ASTA/BS approval is fitted. In case of damage, cut off and fit
a new plug according to the following instructions (discard old plug safely). (UK only - see diagrams right).
Ensure the unit is correctly earthed via a three-pin plug. FOR 230 VOLT 13AMP PLUG SEE fig.1, FOR
110 VOLT PLUG SEE fig.2.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the
cable external insulation extends beyond the cable restraint and that the restraint is tight.
1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection.
A cable reel with an RCD fitted is recommended since any product which is plugged into the cable reel will be
protected. The section of the cores of the cable is important and should be at least 1.5mm², but to be absolutely
sure that the capacity of the cable reel is suitable for this product and for others that may be used in the other
output sockets, we recommend the use of 2.5mm² section cable.
1.2. LIGHT WIRING
 WARNING! Ensure all cables are disconnected from the power supply before attempting following:
Should the lamp need to be re-wired, contact a qualified electrician. The procedure cable into the lamp, proceed
as follows: Remove back cover of terminal box, located at the rear of the lamp, to expose the connection block
and wires, see fig.3. When wired, check that the weather proofing seal is correctly located in the back cover
recess and then replace the back cover.
1.3. GENERAL SAFETY
 WARNING! Disconnect light from the power supply before changing accessories, servicing or performing
any maintenance.
Maintain the light in good condition. Repairs must only be undertaken by a qualified electrician
(use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only, unauthorised parts may be
dangerous and will invalidate the warranty.
Keep a minimum distance of 1 metre from the front of light to the surface which is to be
illuminated.
Locate the light in an adequate area for its function, keep area clean and tidy and free from
unrelated materials.
If using an extension lead, the cable must be fully unwound from the drum.
The lights are weather proof and may be used outdoors. Ensure any extensions and plugs
are weatherproof.
If using a tripod, ensure that the legs are fully extended and are standing on a level, solid
surface. Ensure that the cable is safely routed.
Allow power cables to run down the length of the light stand to the floor. DO NOT allow
power cables to hang from lights above floor level.
DANGER! DO NOT direct the light into a person’s eyes. These models have a very
intense light output which, if incorrectly used, could cause eye damage.
DO NOT touch the light when operating. If needed allow to cool before touching.
DO NOT handle halogen bulbs as the natural oil from hands will shorten the bulb's life.
Handle only with a soft dry cloth.
INSTRUCTIONS FOR:
TELESCOPIC / PORTABLE 130 LED
FLOODLIGHTS 230V/110V
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY
fig.3
fig.2
230V
FUSE RATING - 3AMP
fig.1
MODEL No's: LED130T LED130TD LED130110T LED130110TD LED130110P
© Jack Sealey Limited Original Language Version LED130T, LED130TD, LED130110T, LED130110TD, LED130110P Issue: 1 - 18/06/12

3. GENERAL INSTRUCTIONS
3.1. TELESCOPIC STANDS (LED130T, LED130TD, LED130110T, LED130110TD)
3.1.1. Loosen the locking thumb screw (fig.6D) on the tripod leg collar and slide the collar down, spreading
the legs. Tighten the screw to secure legs in the required position.
3.1.2. Fix the removable head stand (g.5) or the singular lamp onto the top of the stand, secure with hand
screw (g.4A). Check that the electrical cable runs directly down the stand to the oor. DO NOT allow
the cable to extend across the workshop above oor level. Models have storage hooks for excess
cable (fig.6E).
3.1.3. To extend the upright, loosen the locking collar at the end of each section (fig.6B), raise the inner
support to the required height and tighten the locking collars.
3.1.4. Check that the assembly is secure and that all nuts and bolts are tight (DO NOT overtighten). Stand
light on a suitable, level surface before use.
3.1.5. LED130TD and LED130110TD can be removed from the tripod and used with their integral stand
(fig.5).
3.2. GENERAL
3.2.1. Use only Sealey replacement parts. Electrical repairs must only be undertaken by a qualified electrician.
3.2.2. Clean the light with a dry, dust-free cloth. DO NOT use solvents or abrasives to clean the light.
3.2.3. Avoid touching the glass shield as handling may reduce service life and cause the glass to crack. If
necessary clean the shield (when cold) with alcohol and a soft cloth.
3.2.4. If the glass is damaged, replace it immediately. Use genuine Sealey replacement glass. DO NOT use
other glass and
DO NOT use the light without the glass shield.
3.2.5 Should the unit become wet, unplug from mains and wipe dry before storing.
DO NOT use the light without the weather seal intact.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version LED130T, LED130TD, LED130110T, LED130110TD, LED130110P Issue: 1 - 18/06/12
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and
disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or phone [phone].
DO NOT stand on the legs of a telescopic stand, and DO NOT hang other items, or tools, from a telescopic stand.
DO NOT use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its
serviceable life and cause the glass to crack.
DO NOT use the light without the weather seals intact.
DO NOT use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and
then store in a safe, dry, childproof location.
© Jack Sealey Limited
fig.4
fig.5
fig.6
2. SPECIFICATIONS
MODEL No.....LED130T .......LED130TD ..... LED130110T ...LED130110TD .. LED130110P
Power .........8W ............2x8W ......... 8W ...........2x8W ......... 8W
Supply.........230V ..........230V.......... 110V ..........110V.......... 110V
Lumen Output...650lm..........2x650lm ....... 650lm .........2x650lm ....... 650lm