Sealey WST3000 User manual

PORTABLE TRANSFORMERS
MODEL NO’S:
WST1500, WST3000, WST5000, WST10000
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the
correct fuse - see fuse rating in these instructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired
or replaced is repaired replaced immediately by a qualied electrician.
1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualied electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
transformer.
9Familiarise yourself with the application and limitations of the transformer, as well as the potential hazards.
WARNING! Disconnect the transformer from the mains power before performing any maintenance.
9Maintain the transformer in good condition (use an authorised service agent).
9 Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
WARNING! DO NOT connect to mains if any parts are damaged or missing as this may cause failure and/or personal injury.
9Keep the transformer clean for best and safest performance.
9Keep children and unauthorised persons away from the working area.
8DO NOT use the transformer for any purpose other than that for which it is designed.
8DO NOT exceed the rated capacity of the transformer.
8DO NOT allow untrained persons to use the transformer.
8DO NOT use the transformer when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8DO NOT pull the plug from the power supply by the cable.
9 When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
2. i INTRODUCTION
110V Transformer with tool rated performance suitable for intermittent running of power tools and continuous running of lighting products within
specified capacity. IP54 Rated unit with case manufactured from GRP and insulated to class H. Fitted with thermostatic overload protection.
WST1500: Supplied with 2 x 16A/110V sockets and 230V 13A plug.
WST3000: Supplied with 2 x 16A/110V sockets and 230V 13A plug.
WST5000: Supplied with 2 x 16A + 1 x 32A/110V sockets and 230V 13A plug.
WST10000: Supplied with 2 x 32A/110V sockets 4 x 16A/110V sockets and 230V 13A plug.
WST1500, 3000, 5000, 10000 Issue 1 04/04/22
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear Protective
Gloves Warning: Electricity Warning: Hot surface
Isolating
Transformer
Recommended fuse rating
13 Amp

3. i SPECIFICATION
4. OPERATION
4.1. Check the equipment rating and operation against the transformer rating. The transformer will supply intermittently used equipment
up to the plate rating but if the equipment is used continuously then the transformer rating should be reduced see section 3.
4.2. It is normal for the transformer to get warm during use, particularly if being used continuously, so care should be taken to place
only on surfaces that will not be damaged by the heat.
4.3. A temperature sensitive cut-out switch is fitted to prevent overheating. If this switch trips, determine and rectify the cause of
overheating and allow time for the transformer to cool before pressing the reset button. (Located on one of the sides adjacent to the
output sockets).
4.4. The transformer should be plugged directly into a 230V mains socket and should not be supplied via an extension lead. Any
necessary extension lead should be between the transformer and the tool/equipment. Extension leads are available from your
Sealey stockist.
IMPORTANT: The transformer is not double insulated and the safety screen between primary (230V) and secondary (110V) windings
is connected to the earth core of the power cable. For these reasons it is extremely important to confirm that the power socket to be
used is reliably and permanently earthed.
4.5. Tool transformers can draw a very high initial current when switched on. If fuse failure occurs at switch-on check that the fuse is a
13 amp, anti-surge type. Any circuit breaker protecting the supply socket should have a suitable tripping characteristic.
8DO NOT exceed 1.5kV when flash testing.
4.6. A plug suitable for the transformer output is available from your Sealey stockist.
© Jack Sealey Limited
MODEL NO: WST1500 WST3000 WST5000 WST10000
Power tool rating (VA) 1500 3000 5000 10000
Continuous rating (VA) 900 1650 2800 7000
Output Sockets 2 x 16A 2 x 16A 2 x 16A
1 x 32A 2 x 32A/110V sockets 4 x 16A/110V
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Original Language Version WST1500, 3000, 5000, 10000 Issue 1 04/04/22