Seamax Reborn Pro User manual

1 | P a g e
Reborn Pro Tower Bimini Installation Guide
Please take a few minutes to read the entire installation instructions and become familiar with the parts and
installation before beginning to ensure a high quality, trouble free installation. The assembly can be more
easily begun on the ground. A second person will make installation onto the tower more manageable.
Be aware of the following:
•This tower bimini is designed to fit all LT wakeboard’s towers and most other popular brand of towers,
the pictures show the position of the bimini rings on LTX tower.
•Please be careful when your boat is approaching bridges or overpasses.
•Please don’t modify this product, climb, ride or stand on it.
WARNING: Traveling at speeds in excess of 35 mph may cause damage to your bimini top. The canvas
should be removed trailering your boat.

2 | P a g e

3 | P a g e
Step 1: Constructing the frame
- Distinguish the ends of the middle frame side bars. The 2 mini clamps are at the front and the cross fitting is
at rear of the side bars.
-The front frame section and the rear frame section are interchangeable.
-To prevent damage to the side rails, loosen the set screws prior to moving or rotating the mini clamps.
- Connect front/rear frame sections to the middle side bars.
Step 2: Install the rear middle frame bar.
- Assemble the rear middle frame bar as shown in the right figures #1-#3.
- You can do it easily with the pin system.
- Connect the rear middle frame bar on the frame through the cross fittings.
- If the bimini top will be installed above your tower, install the lift fittings (available separately) on the rear
frame bar. (As shown in the right figure #6)
Important note:
If you want to mount this bimini top under the top section of your wakeboard tower, please don’t install the lift
fittings.

4 | P a g e
Step 4: Install the canopy.
- Install the canopy on the frame as shown in the right pictures, you can do it easily with the zipper.
- Assemble the front support bar on the clamp B as shown in the right picture.
Important note:
If you want to install this bimini top under the top section of your wakeboard tower, please refer to step5.
If you want to install this bimini top above the top section of your wakeboard tower, please refer to step6.

5 | P a g e
Step 5: Install the bimini top under the top section of your wakeboard tower.
Install the four bimini rings on the tower’s bars as shown in the right pictures, but don’t tighten the bolts of the
rings.
Please measure the distance between the 2 rings mounted on the rear bars of tower, and adjust the pins to let
the total length of rear frame bar to fit it.
Lift the bimini top, connect the rear middle frame bar with the rings mounted on the rear bars of the tower.
Connect the front support bars with the bimini rings mounted on the front bars of tower.
Now you have installed the tower bimini on the tower as you want. Please make a bit adjustment for the ring to
get the best position, then tighten all of the bolts and set screws.

6 | P a g e
Step 6: Install the bimini top above on the tower
Mount two rings on the front bars of tower, and mount two rings on the top section as shown in the right
pictures, but don’t tighten the bolts of the rings.
•Let the two intubations of the rear middle frame bar to hide inside the frame.
•Lift the bimini top, Connect the two lift fittings with the rings mounted on the top section of the tower.
•Connect the front support bars with the bimini rings mounted on the front bars of tower.
•Now you have installed the tower bimini on the tower as you want.
•Please make a bit adjustment for the ring to get the best position, then tighten all of the bolts and set
screws.
Reborn Tower Bimini Canada Distributor - Seamax Marine & Outdoor
102 –19155 38 Ave, Surrey, BC, Canada V3Z 0Y6
www.seamaxmarine.com 1877-907-7766
[email protected]M