Sears Kenmore Advantage 64291 User manual

!
I
e STAR'I"
CONTROL
OPERATINGSTATUS
SYMBOLS
_Jl LINT SCREEN
B SAFETY DOOR
SWITCH
1_ ERFORMANCE
GUIDE LABEL
_DEL NO. PLATE
mm m
If you need SERVICE or PARTS for your Kenmore dryer:
Be ready to give your Sears Service Department the model number, serial number and date of
purchase. Write in below. The plate i¢1with model and serial numbers is located behind the
dryerdoor.
iii
,.1tO. [ M
MODEL NO. SERIAL NO. IDATE OF PURCHASE
ELECTRIC
MODEL 64291
GAS
MODEL 74291

How to dry a load of laundry
b/_ Clean lint screen before each load.
Put laundry into dryer and shut
the door.
Set Cycle Selector Control Ill.
[_) ush the Start Control Ill1to start
your dryer.
Remove load when dry.
I! |l
Ill Cycle Selector Control
Use this control to select the proper drying method for the type of
items in the load. The control can be set for Timed Drying or Air.
You can turn the control at any time to make drying time longer
or shorter or you can turn the control to an OFF position to shut
the dryer off.
il Start Control
Use this control to start the dryer. Be sure the door is closed.
Opening the door stops the dryer. It will not startagain until you
close the door and push the START control. Be sure the Cycle
Selector Control is on a dry setting.
OPERATING STATUS SYMBOI__
Color coordinated keys indicate in which portion of the cycle the
dryer is operating.
Part No. 3392338

Ill CYCLi_ SELECTOR CONTROL
NORMAL Cycle
Use this cycle to get upto 120 minutesof drying time athigh heat followed
by a5minute (approx.) cooldown.
• Set the Cycle Selector Control to the amount of time you want in the
Normal Cycle.
•Push the Start Control.
PERMANENT PRESS Cycle
Use this cycle to get up to 50 minutes of drying time at high heat followed
by a 10 minute (approx.) cooldown.
• Set the Cycle Selector Control to the amount of time you want in the
Permanent Press Cycle.
• Push the Start Control.
AIR DRY Cycle
Use this cycle to get up to 30 minutes of drying tirn.ein room temperature
air. Use this setting for items that will not tolerate heat, such as plastics,
foam rubber, etc. and for airing and fluffing items such as pillows.
•Do not dry these items with heat.
• Set the Cycle Selector Control for the number of minutes you want in the
Air Dry Cycle.
•Push the Start Control.
Cooldown
Approximately five or ten minutes before the end of the drying cycle,
clothes are tumbled without heat to help reduce wrinkles and make clothes
more comfortable to handle.

FEATURES
E1 Lint Screen
Keep the lint screen clean. A lint-clogged screen will slow down the flow
of air. This makes drying time longer and wastes energy. Clean the lint
screen before each load as follows:
!. With dryer off, remove the screen by pulling straight up.
2. Roll the dry lint off the screen. Do not wet the screen or lint; wet lint is
hard to remove.
3. Replace the cleaned lint screen.
_Yir_!i_JlXe]
Fire Hazard.
Do not use your dryerwhile the lint screen is removed.
It could cause overheating and possible damage to fabrics and dryer
parts or create a fire hazard. Lint screen must be pushed firmly into
place.
NOTE: If lint screen gets clogged by detergent orfabric softener build-up,
remove and clean it with a nylon brush, hot water and liquid detergent.
Dry and replace screen.
E1 Safety Door Switch
For safety, the switch shuts off dryer when door is opened. Dryer will not
start until door is closed and START is pushed. Be sure the Cycle Selector
Control is on a dry setting.
[[3 Performance Guide Label
Located inside the dryer door. Gives information on what to do if dryer
does not perform normally.
NOTE: If dryer drum is stained, clean it with a damp cloth and mild
detergent.
l_l Model No. Plate
Shows model and serial numbers. Have these ready if you ever call for
service.
!
Formore detailed drying times, rules for safe operation, fabric care, |
maintenance and installation information, refer to the LAUNDRY I
GUIDE and INSTALLATION INSTRUCTIONS you rex_ived with
your dryer.
II I
Part No. 3392338 Printed in U.S.A.