Seav BeSAFE RX Series User manual

BeSAFE RX SINGLE-CHANNEL RECEIVER
The BeSAFE RX radio receiver is designed for the remote operation of
electrical and electronic equipment in conjunction with one or more
SEAV radio-controls and/or transponders (BeSAFE Card, BeSAFE Key).
- Mod. (BeSAFE RX 30,875): 30,875 MHz
- Mod. (BeSAFE RX 306): 306 MHz
- Mod. (BeSAFE RX 310): 310 MHz
- Mod. (BeSAFE RX 418): 418 MHz
- Mod. BeSAFE RX 433 : 433,92 MHz
- Mod. BeSAFE RX 868 : 868,3 MHz
( ) This product is destined for countries in which use is consented.
TECHNICAL DATA
- Power supply: 12-24VAC-DC
- Max consumption: 4.5 W
- Op. radio-controls: 12-18 Bit or Rolling Code
- Op. transponders: Card or Key-ring
- Stored codes: 500 Max
- 1 (one) command relay: 30VDC 1A
- Working temperature: -10°C ÷55°C
- Dimensions: 110x121x47 mm
- Container: ABS (UL94V-0)
- Protection degree: IP54
- Radio-control range in open spaces: 30-70 metres
CONNECTION OF TERMINAL BOARDS
CN1: 1 : 24 VAC/DC power supply input.
2 : 0 V power supply input.
3 : 12 VAC/DC power supply input.
4 : Clean command contact output.
5 : Clean command contact output.
6 : Earth input.
7 : Antenna hot pole input.
CN2: Connection for Transponder 1 Reader (BeSAFE Reader ).
CN3: Connection for Transponder 2 Reader (BeSAFE Reader ).
CN4: Connection for PC “SW 2189” interface.
CN5: Normally open or closed command contact selection.
RECEIVER INSTALLATION
For the optimal operation between transmitter and receiver, we recom-
mend you choose the point of installation carefully. The range is not
merely linked to the technical features of the device itself, but it actually
varies according to the radioelectric conditions of the area.
The receiver is fitted with an antenna consisting of a rigid wire section.
Should you wish to increase the device sensitivity, you can connect a
tuned antenna using a RG58 50 OHM coaxial cable. The antenna
should be placed on the exterior in a visible position away from any
metallic structures.
The installation of two receivers placed less than 5 metres from one an-
other is not possible.
OPERATION WITH RADIO-CONTROLS AND/OR TRANSPONDERS
The receiver can be combined with SEAV radio-controls and/or
transponders and is designed to store up to 500 different users. We
therefore recommend you make a note of the “memory position - user
name” correspondence in the form provided. For use with radio-controls,
the receiver is fitted with an incorporated receiver. For use with “Be-
SAFE CARD and BeSAFE KEY” transponders, the connection of
one or two “BeSAFE Reader“ proximity readers supplied as option-
als will be necessary.
PROGRAMMING RADIO-CONTROLS AND/OR TRANSPONDERS
The programming of radio-controls and/or transponders is self-learning,
as follows.
Use the UP or DOWN keys to go to the desired memory position
(viewed on the display from 001 to 500), paying attention to the TRANS-
MITTER and TRANSPONDER LEDS, as one of them turning on means
the location is busy. Press the SEL key, the TRANSMITTER and
TRANSPONDER LEDS will begin to flash, and meanwhile send the
code with the radio-control or bring the transponder closer to the “Be-
SAFE Reader” proximity reader, (the display will indicate STO stored),
the TRANSMITTER or TRANSPONDER LED will go from off to on and
programming is thus complete.
To delete a radio-control or transponder stored previously, use the UP or
DOWN keys to go to the memory location that is busy, press the SEL
key, the TRANSMITTER or TRANSPONDER LED will begin to flash;
press the SET key (the display will indicate "DEL" deleted), the LED will
go from on to off and delete is thus complete.
During normal operation, the display panel indicates the memory loca-
tion of the device stored previously currently in use.
RAPID PROGRAMMING OF RADIO-CONTROLS AND/OR TRANSPONDERS
The rapid programming of radio-controls and/or transponders is only al-
lowed when all the receiver memory is free. To make sure that all the
memory is free, follow the Reset procedure.
Rapid programming means you do not have to select a new memory loc-
ation for another radio-control and/or transponder every time, but start-
ing from position 001, the control unit automatically increases the
memory location and remains on standby for 10 seconds, from the input
of a new radio-control and/or transponder to store.
PASSWORD
Once you have finished programming the radio-controls and/or
transponders, you can store a password in the PAS position, to disable
and enable receiver programming, as follows.
Use the UP or DOWN keys to go to the PAS memory position, press the
SEL key, the TRANSMITTER and TRANSPONDER LEDS will begin to
flash, and meanwhile use the UP or DOWN key to select a number
between 001 and 500, press the SET key, (the display will indicate
"CLO" closed), and the TRANSMITTER and TRANSPONDER LEDS will
go from off to on.
To re-enable programming, use the UP or DOWN keys to go to the PAS
memory position, press the SEL key, the TRANSMITTER and
TRANSPONDER LEDS will begin to flash, meanwhile use the UP or
DOWN keys to select the key number selected previously, press the
SET key, (the display will indicate OPE open).
To delete a password (operation only allowed if the system is open
OPE), use the UP or DOWN keys to go to the PAS memory position,
press the SEL key, the TRANSMITTER and TRANSPONDER LEDS will
begin to flash and meanwhile press the SET key (the display will indicate
DEL deleted), the TRANSMITTER and TRANSPONDER LEDS will go
from on to off.
N.B.: if you enter an incorrect password, you will have to wait 5 minutes
to repeat the operation, and if you enter another incorrect password, you
will have to wait 1 hour.
RESET
If it is appropriate for the factory configuration to be restored (operation
only allowed if the system is open OPE), press the SEL and SET keys
simultaneously, and the LEDS will turn off, and the display will indicate
the PAS position.
N.B.: the display is turned off after one minute of inactivity to save en-
ergy.
1 Rev. 1.2 03/07
GB

FURTHER FUNCTIONS VIA PC CONNECTION
The receiver can be connected to a Personal Computer through the use
of a “SW 2189” package supplied as an optional, thanks to which you
may access further functions.
FOR THE INSTALLER - IMPORTANT
−All operations requiring the opening of the casing
(such as installation, programming and repair, etc.) must be
carried out by skilled staff only.
−The fixing of power supply leads and connection cables must be
secured through the use of cable clamps.
SEAV s.r.l. hereby declares that the product below:
BeSAFE RX Single-channel Receiver complies with the re-
quirements of Directive R&TTE 99/5/EC.
1 Rev. 1.2 03/07