SECO-LARM ENFORCER Zeta Series User manual

OSD (On-Screen Display)
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
Manual
For the following cameras:
NTSC Model #
PAL Model #
Lens
Resolution
IR
LEDs
EV-1806-N3GQ
EV-1806-P3GQ
3.6mm
600 TV lines
30
EV-1816-N6GQ
EV-1816-P6GQ
6.0mm
600 TV lines
42
EV-1816-NKGQ
EV-1816-PKGQ
2.8~12mm
600 TV lines
42
EV-1826-NKGQ
EV-1826-PKGQ
2.8~12mm
600 TV lines
84
In-Line Joystick
Built into the camera
Program the OSD from the camera
2 Different OSD Programming Options:
Optional External Controller (Model: EV-18C)
Access the OSD near the DVR without
having to uninstall the camera
One controller can be used to program
several cameras

ENFORCER Zeta Series OSD (On-Screen Display)
2SECO-LARM U.S.A., Inc.
Table of Contents:
Programmable Features …………………..
Connecting the Controller …..……………..
Sample Installations ……………………….
Menu Setup ….……………………………...
Menu Diagram………………………………
Language ……………………………………
Camera ID …………………………………..
Lens ……………………………….…………
Shutter / Automatic Gain Control (AGC) …
Day / Night Mode………………….………..
Backlight Compensation (BLC)……………
Adaptive Tone-Curve Reproduction (ATR)…….
White Balance …………………………………….
Picture Adjustment ……………………………….
2D Noise Reduction (NR) ..………………………
Privacy Masking …………………………………..
Motion Detection………………………………….
Sync ………………………………………………..
Reset……………………………………………….
Next / Back………………………………………...
Exit………………………………………………….
Troubleshooting…………………………………...
2
3
3
4
5
7
7
7
8
9
10
11
11
13
13
14
15
15
15
15
15
16
Programmable Features:
Shutter
Manually adjust the shutter speed
Day / Night Mode
Adjust the level that the camera switches from
color to B/W when the ambient light is low
Backlight Compensation (BLC)
Adjust the exposure to properly display the
subject in front of the bright light source.
Highlight Compensation (HLC)
Define target areas and remove spotlights to
make certain objects visible
Adaptive Tone-Curve Reproduction (ATR)
Adjust the brightness values of the image for a
more detailed picture
White Balance
Adjust the color temperature and image color
of the picture
Picture Adjustment
Adjust the camera’s brightness, contrast,
sharpness, hue, and gain
2D Noise Reduction (NR)
Adjust for less interference on the screen in
an area with low illumination
Privacy Masking
Block out a certain portion of the image
Motion Detection
Detect if there is motion in the scene
HLC OFF
HLC ON
2D NR OFF
2D NR ON
ATR OFF
ATR ON
Privacy Masking OFF
Privacy Masking ON

ENFORCER Zeta Series OSD (On-Screen Display)
SECO-LARM U.S.A., Inc. 3
There are three ways to use the optional OSD controller:
1. Near the camera with optional local monitor (Fig. 1) –Plug the camera’s video cable into the
OSD controller’s “BNC In” port, and plug the local monitor’s cable into the OSD controller’s
“BNC Out” port. Programming can be done by the camera installer.
2. Near the camera, but no optional remote monitor (Fig. 1) –Plug the camera’s video cable into
the OSD controller’s “BNC In” port, and plug the cable from the DVR or remote monitor into
the OSD controller’s “BNC Out” port. Programming in this fashion may require two people.
3. Near the DVR or other video target (Fig. 2) –Connect the cable from the camera into the OSD
controller’s “BNC In” port, and plug the cable from the DVR or other video target into the OSD
controller’s “BNC Out” port.
NOTE: Connect power to the OSD controller only AFTER the device is connected to the video cables.
Please read the camera installation manual for safety precautions and detailed instructions on
how to install the camera.
Connecting the Controller:
Sample Installations for the Optional Zeta Series OSD Controller:
Fig. 2: Access on DVR / Multiplexer Side.
Fig.1: Access on Camera Side.
Remote
DVR, multiplexer
Monitor
Zeta Series
Camera
Included 12VDC
power adapter
OSD
Controller
Remote
DVR, multiplexer
Monitor
Included 12VDC
power adapter
OSD
Controller
Optional
local monitor
Zeta Series
Camera

ENFORCER Zeta Series OSD (On-Screen Display)
4SECO-LARM U.S.A., Inc.
Menu Setup
Menu items can be selected by using the OSD (On Screen Display) Controller.
1. If the Menu ON LED is lit, press the ENTER button.
The SETUP menu will be displayed on the monitor.
2. Move to and select the required function using the UP
and DOWN buttons.
3. Change the menu setting using the LEFT and RIGHT
buttons.
Available values are displayed by pressing the LEFT
and RIGHT buttons.
4. After choosing the setting, move the cursor to EXIT
and press the ENTER button to exit.
When the Menu Control is off, the OSD controller will access its secondary functions. The up
and down arrows will control the zoom. The left and right arrows will control the brightness.
Move to available options by moving the cursor to the desired feature.
A submenu is available where the options reads .
Note:
Note:
SHIFT
ENTER
In-Line Joystick
1. Press down on the joystick to open the OSD menu.
2. Use the joystick to navigate the OSD menu.
3. To select an item, press down on the joystick.
Zeta Series-OSD Controller
Menu Diagram 1
Menu Diagram 2

ENFORCER Zeta Series OSD (On-Screen Display)
SECO-LARM U.S.A., Inc. 5
Menu Diagram 1:
1 In MANUAL lens mode, only SHUT mode is available. In AUTO lens mode, SHUT + AUTO IRIS and AUTO IRIS
modes are also available.
Continued on next page
SETUP MENU
SETTING
SETTING OPTIONS
1) LANGUAGE
(see page 6)
English, Japanese, German, French, Russian,
Portuguese, Spanish, Simplified Chinese
2) CAMERA ID
(see page 7)
ON
Set a name for the camera to display on screen
OFF
Disable camera ID
3) LENS
(see page 7)
AUTO
TYPE: DC
MODE: AUTO / OPEN / CLOSE
SPEED: 0~255 Level Adjustable
MANUAL
Set for fixed lens camera
4) SHUTTER / AGC
(see page 8)
AUTO
High Luminance: MODE1: SHUT + AUTO IRIS / AUTO IRIS
/ SHUT
BRIGHTNESS: 0~255 Level Adjustable
Low Luminance: MODE: AGC / OFF
BRIGHTNESS: x0.25, x0.50, x0.75, x1.00
MANUAL
MODE: SHUT + AGC
SHUTTER: 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
AGC: 6.00, 12.00, 18.00, 24.00, 30.00, 36.00, 42.00, 44.80
5) DAY / NIGHT
(see page 9)
AUTO
BURST: ON / OFF
DELAY CNT: 0~255 Level Adjustable
DAY NIGHT: 0~255 Level Adjustable
NIGHT DAY: 0~255 Level Adjustable
COLOR
Display color image
B/W
BURST: ON / OFF
6) BACKLIGHT
(see page 10)
OFF
Disable backlight compensation
BLC
Enable backlight compensation
HLC
Enable highlight compensation
7) ATR
(see page 11)
ON
LUMINANCE: LOW / MID / HIGH
CONTRAST: LOW / MIDLOW / MID / MIDHIGH / HIGH
OFF
Disable adaptive tone-curve reproduction
8) NEXT
Access Menu Diagram 2
9) EXIT
Exit menu and save settings
10) SAVE ALL
Save menu setting without exiting the menu

ENFORCER Zeta Series OSD (On-Screen Display)
6SECO-LARM U.S.A., Inc.
SETUP MENU
SETTING
SETTING OPTIONS
WHITE BAL
(see page 11)
ATW
SPEED: 0~255 Level Adjustable
DELAY CNT: 0~255 Level Adjustable
ATW FRAME: x0.50, x1.00, x1.50, x2.00
ENVIRONMENT: INDOOR / OUTDOOR
PUSH
Disable white balance mode
USER1
B:GAIN: 0~255 Level Adjustable
R:GAIN: 0~255 Level Adjustable
USER2
B:GAIN: 0~255 Level Adjustable
R:GAIN: 0~255 Level Adjustable
ANTI CR
Enable anti-color rolling
MANUAL
LEVEL: 22~44 Level Adjustable
PUSH LOCK
Disable white balance mode by pressing enter
PICT ADJUST
(see page 13)
MIRROR
ON / OFF
BRIGHTNESS
0~255 Level Adjustable
CONTRAST
0~255 Level Adjustable
SHARPNESS
0~255 Level Adjustable
HUE
0~255 Level Adjustable
GAIN
0~255 Level Adjustable
NR
(see page 13)
ON
NR MODE: OFF / Y / C / Y/C
Y LEVEL: 0~15 Level Adjustable
C LEVEL: 0~15 Level Adjustable
OFF
Disable 2D noise reduction
PRIVACY
(see page 14)
ON
AREA SEL: Up to 4 selectable zones
TOP: 0~244 Level Adjustable
BOTTOM: 0~244 Level Adjustable
LEFT: 0~378 Level Adjustable
RIGHT: 0~378 Level Adjustable
COLOR: White / Black / Red / Green / Blue / Yellow / Cyan
/ Magenta
TRANSP: 0.00, 0.50, 0.75, 1.00
MOSAIC: ON / OFF
OFF
Disable privacy masking
MOTION DET
(see page 15)
ON
DETECT SENSE: 0~127 Level Adjustable
BLOCK DISP: ON / OFF / ENABLE
MONITOR AREA: ON / OFF
AREA SEL: Up to 4 selectable zones
TOP: 0~244 Level Adjustable
BOTTOM: 0~244 Level Adjustable
LEFT: 0~378 Level Adjustable
RIGHT: 0~378 Level Adjustable
OFF
Disable motion detection
SYNC
(see page 15)
Internal synchronous mode
CAMERA RESET
(see page 15)
Reset the camera to factory setting
BACK
Access Menu Diagram 1
EXIT
Exit menu
SAVE ALL
Save menu setting
Menu Diagram 2:

ENFORCER Zeta Series OSD (On-Screen Display)
SECO-LARM U.S.A., Inc. 7
Camera ID:
This function is used to set a name for the camera.
1. Select CAMERA ID on the SETUP menu screen.
2. Turn the CAMERA ID ON or OFF by pressing the LEFT and RIGHT buttons (OSD
controller) or the joystick button.
3. If CAMERA ID is ON, use the cursor to select the character in the alphabet list. Press
the ENTER button (OSD controller) or the joystick button to input the character.
4. Select RETURN to return to the SETUP menu.
CHR1/CHR2: Change the characters.
: Adjust the cursor position.
CLR: Forward delete the selected
character.
POS: Set the location of the camera
ID text.
RETURN: Save and return to the
SETUP menu.
Lens:
This function is used to select the camera’s lens type.
1. Select LENS on the SETUP menu screen.
2. Select the desired lens type by pressing the LEFT and RIGHT buttons (OSD controller)
or the joystick button.
3. Select RETURN to return to the SETUP menu.
Type: Select lens type (DC).
Mode: Select the mode (AUTO,
OPEN or CLOSE).
SPEED: Set the auto iris movement
speed. Adjustable range: 0~255.
AUTO: Select automatic mode for
DC Auto Iris lens.
MANUAL: Select manual mode for
manual or fixed lens.
Language:
This function is used to select the OSD display language.
1. Select LANGUAGE by moving the cursor UP and DOWN on the SETUP menu screen.
2. Select the desired language by pressing the LEFT and RIGHT buttons (OSD controller) or
the joystick button.

ENFORCER Zeta Series OSD (On-Screen Display)
8SECO-LARM U.S.A., Inc.
A. HIGH LUMINANCE
MODE: Select shutter mode.
SHUT –Length of time a
camera’s shutter is open.
AUTO IRIS –Adjust the iris to
allow specific amount of exposure.
SHUT + AUTO IRIS –
Combination of both SHUT and
AUTO IRIS.
In manual lens mode only SHUT
mode is available. In automatic
lens mode AUTO IRIS or
SHUT + AUTO IRIS mode are
also available.
BRIGHTNESS: Set the auto-exposure image brightness.
Adjustable range: 0~255.
B. LOW LUMINANCE
MODE: Select low luminance mode (AGC or OFF).
BRIGHTNESS: Select the automatic gain value. This setting has no effect if
AGC is on. Adjustable range: x0.25, x0.50, x0.75, x1.00.
MODE: Select shutter mode
(SHUT + AGC).
SHUTTER: Selectable shutter speed.
Adjustable range: 1/60, 1/100, 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10000.
AGC: Set the gain value. Adjustable
range: 6.00, 12.00, 18.00, 24.00, 30.00,
36.00, 42.00, 44.80.
Shutter / Automatic Gain Control (AGC):
This function is used to manually adjust the shutter speed and AGC settings.
1. Select SHUTTER / AGC on the SETUP menu screen.
2. Select the desired shutter or AGC type by pressing the LEFT and RIGHT buttons (OSD
controller) or the joystick button.
3. Select RETURN to return to the SETUP menu.
AUTO: The camera is in automatic
shutter mode.
MANUAL: The camera is in a fixed shutter mode.

ENFORCER Zeta Series OSD (On-Screen Display)
SECO-LARM U.S.A., Inc. 9
Day/Night Mode:
This function will automatically switch to color mode in normal conditions and black/white
(B/W) mode when ambient light is low.
1. Select DAY/NIGHT on the SETUP
menu screen.
2. Select the desired DAY/NIGHT
setting by pressing the LEFT and
RIGHT buttons (OSD controller) or
the joystick button.
3. Select RETURN to return to the
SETUP menu.
BURST: Set the BURST mode (ON or OFF). When BURST mode is ON, the image
colors will be suppressed, but present when the camera switches to B/W mode. When
the BURST mode is OFF, the image colors will be B/W when the camera switches to
B/W mode.
DELAY CNT: Set the COLOR/B&W interchange delay time. Adjustable range: 0~255 sec.
DAY NIGHT: Define light level to trigger B/W mode. Adjustable range: 0~255.
NIGHT DAY: Define light level to trigger COLOR mode. Adjustable range: 0~255.
BURST: Set the BURST mode (ON
or OFF). When the BURST mode is
ON, the image colors will be
suppressed, but present. When the
BURST mode is OFF, the image
colors will be B/W.
AUTO: The camera image will switch
to color in normal situation and B/W
when ambient light is low.
B/W: The camera image will always display in B/W.
COLOR: The camera image will always display in color.

ENFORCER Zeta Series OSD (On-Screen Display)
10 SECO-LARM U.S.A., Inc.
Backlight Compensation (BLC):
This function is used to control the light-level to overcome strong backlight conditions.
1. Select BACKLIGHT on the SETUP menu screen.
2. Select the desired BLC mode by pressing the LEFT and RIGHT buttons (OSD controller)
or the joystick button.
HLC ON
HLC OFF
Backlight Compensation (BLC): Select this mode to correct the exposure of the
subjects in front of a strong backlight.
Highlight Compensation (HLC): Select this mode to improve the picture by
displaying shades of grey on the strong backlight.
BLC ON
BLC OFF