SECO-LARM SLI ENFORCER ENHANCED MVE-AH1H1-01GQ User manual

®®
ENFORCER
®
Manual
Extend HDMI signals up to 230ft (70m) at 1080p over a single Cat5e/6 cable
Supports resolutions from 480i up to 4Kx2K/UHD
Plug and play operation –comes as a complete set
Bi-directional IR for remote control extension
Includes one (1) 24VDC locking power supply –set can be powered at either end
HDMI®Extender
over Cat5e/6
MVE-AH1H1-01GQ

ENFORCER Enhanced HDMI®Extender over Cat5e/6
2SECO-LARM U.S.A., Inc.
The ENFORCER Enhanced HDMI Extender over Cat5e/6 extends the range of HDMI signals by using an active
transmitter and receiver to send video and audio over a single Cat5e/6 cable. 1080p HDMI signals can be transmitted
up to 230ft (70m) between the two units with zero signal loss, while 4Kx2K/UHD HDMI signals can be transmitted up
to 130ft (40m). The extender supports IR signals using the included IR transmitter and receiver, allowing the user to
use a remote control from one end of an installation to control a device such as a TV or media player at the opposite
end of the installation. A single power supply can power both devices from either end of the installation.
Signal Strength –Active operation ensures that the signal strength will remain strong over the length of the cable.
Distance –The Enhanced HDMI Extender over Cat5e/6 can transmit a clear HDMI signal up to 230ft (70m).
Formats Supported –The Enhanced HDMI Extender over Cat5e/6 support both progressive and interlaced
formats: 4K/1080p/1080i/720p/576p/576i/480p/480i.
Plug and Play –The Enhanced HDMI Extender over Cat5e/6 comes as a complete set consisting of a transmitter,
receiver, power supply, and IR adapters. No adjustments or settings need to be made. The unit is ready to use
right out of the box.
Zero Signal Loss –Integrated circuits in the transmitter and receiver clean, buffer, and amplify the HDMI signal.
This prevents signal loss and ensures a clear signal regardless of the length of the cable up to the maximum range.
Bi-Directional IR –Send IR signals from the source to the monitor or from the monitor to the source for discrete
operation of devices.
Connect Multiple Units –Repeat up to four sets to extend HDMI range up to 918ft (280m).
Model
MVE-AH1H1-01GQ
Input video signal
3.3V
Input DDC signal
5Vp-p (TTL)
Maximum single link range
4Kx2K@30Hz
Deep color
48-bit
Video formats supported
High-speed HDMI with 3D, HDCP 1.2
Audio formats supported
LPCM, Dolby-AC3, DTS 7.1, DSD
Output video
HDMI
Resolutions supported
4K/1080p/1080i/720p/576p/576i/480p/480i
Range –1080p
Cat6
Up to 230’ (70m)
Cat5e
Up to 196' (60m)
Range –4K
Cat6
Up to 130’ (40m)
Cat5e
Up to 98' (30m)
Video amplifier bandwidth
10.2Gbps
Video input connector
HDMI Type A 19-pin female
Maximum input cable length
24AWG: 50' (15m); 26AWG: 32' (10m); 28AWG: 16' (5m)
Cat5e/6 wiring standard
T568-B
IR pass-through
30~50kHz
Operating voltage
24VDC
Power supply
1A@24VDC (1 adapter) (2.1mm plug)
ESD protection (human body model)
±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw
Transmitter
150mA@24VDC
Receiver
250mA@24VDC
Operating temperature
32°~104° F (0°~40° C)
Operating humidity
20~90% RH (no condensation)
Dimensions
315/16”x29/16”x1” (100x65x25mm)
Weight
7.1-oz (200g) (each)
Introduction:
Features:
Specifications:

ENFORCER Enhanced HDMI®Extender over Cat5e/6
SECO-LARM U.S.A., Inc. 3
Transmitter
1. Determine where the transmitter and receiver will be wired as well as how much Cat5e/6 cable
will be necessary.
2. Connect the HDMI cable to both the transmitter and the source device.
3. Connect the HDMI cable to both the receiver and the display.
4. Connect the Cat5e/6 cable to both the receiver and transmitter units.
Note: For best results, use Cat6 or better cable.
5. Connect the 24VDC adapter to either the transmitter or receiver.
6. Determine which device, if any, will be controlled by the remote control. Install the IR transmitter
to the IR-TX port of the extender nearest the device to be controlled, pointing the IR transmitter
at the device. Install the IR receiver to the IR-RX port of the other extender unit. Point the
remote control at the IR receiver when in use.
7. Switch on the HDMI source and display to verify that the system is functioning properly.
8. If necessary, use the included brackets and screws to mount the extender to a wall or desk.
1x Transmitter
1x Receiver
1x Manual
2x IR Transmitters
2x IR Receivers
1x 24VDC Locking power adapter
4x Mounting brackets
8x Mounting bracket screws
Receiver
1"
(25mm)
29/16"
(65mm)
315/16"
(100mm)
Overview:
Parts List:
Installation:

ENFORCER Enhanced HDMI®Extender over Cat5e/6
4SECO-LARM U.S.A., Inc.
NOTICE: The information and specifications printed in this manual are current at the time of publication. The SECO-LARM policy is one of
continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is not responsible for misprints.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without
the written permission of SECO-LARM.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PICHN3
Tel: [phone] | [phone]
Email: [email protected]
MI_MVE-AH1H1-01GQ_160323.docx
Sample Application:
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period
of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any
defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating
properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any
kind to the purchaser or anyone else.
Cable Legend:
HDMI
Cat5e/6
Power
IR
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLCC in the United
States and other countries.
HDMI device does not function
correctly
Use T568-B wiring standard
Make sure the maximum lengths are not exceeded for either the type of
HDMI or Cat5e/6 cable used (see specifications chart for both cables)
Make sure the source and the display are powered.
Test the Cat5e/6 cable between the receiver and transmitter and make
sure it is functional.
Make sure that there are no problems with the HDMI source, HDMI
cables, or HDMI display by plugging the source directly into the display
using an HDMI cable
Make sure that the transmitter and receiver are plugged into the correct
units
Make sure the HDMI source is compatible with the HDMI display.
Troubleshooting:
* Power supply can be installed at either end
Receiver
HDMI Source
IR Rx
Display
IR Tx
Up to 230' (70m)
Receiver
HDMI Extender over Cat5e/6
24VDC*
Power supply
Remote
control
24VDC*
Power supply
Transmitter
Transmitter
HDMI Extenderover Cat5e/6