SECO-LARM ENFORCER RM-R100-KB1Q User manual

®
What's Included with the Kit
:
Basic DIY Installation Using Micro USB Power:
Room
Occupancy
Monitor
Quick Guide Manual
1x
Sensor
1x
1
-
Room Indicator
1x
Indicator decal
s
2x
12"
USB Power cords
1x Manual
verview:
Pairin button
Micro USB Power input
PIR Sensor
Phototransistor
Phototransistor ON/OFF jumper*
LED ON/OFF jumper
*
PIR ON/OFF jumper
*
Sensor
See full Manual for terminal block wirin instructions
Service b
utton (1
-
Room Indicator) / Ch2 P
airin button
(2-Room Indicator)
Ch1 Pairin button
Micro USB power input
Antenna
Buzzer
(1-Room Indicator only)
Buzzer ON/OFF jumper
*
(1
-
Room Indicator only)
Indicators
See full Manual for terminal block wirin instructions
The Room Monitor Kit
(RM
-
R100
-
KB1Q) is pre
-
learned and ready to o ri ht out of the box. Just mount and connect to
power via the included micro USB cable and any USB adapter. Follow the steps below for a basic installation.
1.
Find a l
ocation to mount the Sensor/
Indicator.
Keep in
mind that the included micro USB cord is 12" lon .
2.
Use a paper clip and pro ram as needed. See
Setting a
Reminder Time on p . 2.
3.
Apply double
-
sided mountin tape to the back of the
Sensor/Indicator and mount.
4.
Connect the micro USB plu to the
Sensor/Indicator
and connect to power.
Power
source
12"
(30cm)
For
complete instructions
, please
see the
full Manual on the SECO-LARM website.
*Phototransistor jumper's default is OFF, other jumpers' default is ON

ENFORCER Room Occupancy Monitor
2SECO-LARM U.S.A., Inc.
Setting a Reminder Time:
Additional 2
-
Room Indicator
Wall-Mount Help Button Indicator Remote
RM
-
R100
-
R2Q
RM
-
R100
-
TBQ
RM
-
R100
-
TH2Q
Also Available from
SECO
-
LARM
®
:
FCC C MPLIANCE
STATEMENT
FCC ID:
K4ER100TLQ
THIS DEVICE COMPLIES WITH PART 15 OF T
HE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The chan es
or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no chan e to the antenna or the
device is
permitted. Any chan e to the antenna or the device could result in the device exceedin the RF exposure
requirements and void user’s authority to operate the device.
PITSW1
Order Part# 763
-
189
-
1
%
MQ_RM
-
R100
-
xxxQ_190328.docx
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
N TICE
:
The SECO
-
LARM policy is one of continual development and improvement. For
that reason, SECO
-
LARM
reserves the ri ht to chan e specifications without notice. SECO-LARM is also not responsible for misprints.
All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyri ht © 2019 SECO-LARM U.S.A., Inc
. All
ri hts reserved.
WARRANTY:
This SECO
-
LARM product is warranted a ainst defects in material and workmanship while
used in normal
service for
one
(
1
)
year
from the date of sale to the ori inal customer.
1.
Connect to power
and press the pairin button within 5 seconds of powerin on.
2. After pressin the pairin button, count number of times the LEDs flash.
3. Press the pairin button until desired reminder time is set. See table below for reminder time settin s.
# of Flashes
1
2
3
4
5
6
7
Reminder time
Disabled
3min
5min
10min
15min
20min
30min
The Room Monitor
Sens
ors and Indicators
can be pro rammed to flash if the room has been occupied for an extended
period of time.
Pairin
button
LED
Indicator
Sensor
(RM-R100-TLQ)
Service
pairin *
button
Ch1 Pairin
button
LED
Indicators
1
-
Room Indicator
(RM-R100-RB1Q)
Ch1
Pairin
button
LED
Indicators
Ch2
Pairin
button
2
-
Room Indicator
(RM-R100-R2Q)
IMP RTANT
:
For instructions on how to pair additional Sensors and Indicators
, terminal block wirin
instructions, and other additional information, please see the full Manual on the SECO-LARM website.
*Service pairin button cannot be used to set a reminder time.