SECO-LARM SLI ENFORCER PD-4PTQ User manual

Access Power Distribution Boards
Manual
Features:
•
For 12/24 VAC/VDC operation
•Each output individually used
•Each output can operate in both ail-sa e
and ail-secure modes
•Each output individually controlled
•Individual output relays (10A@24VDC)
•Output uses rated at 3.0A (PT[email protected])
•Individual status LEDs or each output and
or emergency input
•Auxiliary supervision relay (1A@28VDC)
•
Equipped with dry and wet trigger inputs
(blade versions only)
•Includes auxiliary inter ace to enable
emergency egress, alarm monitoring, or to
trigger other devices
•Includes auxiliary inter ace disconnect,
individually selectable or each output
•Compatible with ENFORCER Access
Control Power Supplies
Model
Outp
ut Fuse
No. of
Outputs
Main
Fuse
Type
Rating
PD
-
4PTQ
PTC
2.5A
4
10A
PD
-
4B
TQ
Blade
3.0A
4
10A
PD
-
8
PTQ
PTC
2.5A
8
10A
PD
-
8B
TQ
Blade
3.0A
8
10A
PD
-
8BTQ shown

ENFORCER Access Power Distribution Boards
2SECO-LARM U.S.A., Inc.
The ENFORCER 4 and 8 output Access Power Distribution Boards centralizes the power sources
and gives individual control or various access control locking devices, such as electromagnetic
locks, electric shear locks, door strikes, deadbolt locks, and more. Each output is individually
controllable, individually used, and with individual status LEDs. Each output can operate in ail-
sa e or ail-
secure modes. Each board includes wet and dry trigger inputs or emergency activation
and includes power ailure supervision relays and auxiliary supervision relays.
1x
Power distribution board
4x
Mounting spacers
1x
Manual
Model PD-4PTQ PD-4BTQ PD-8PTQ PD-8BTQ
Input voltage 12/24 VAC/VDC
Input current draw 10A@24VAC
Number o outputs 4 8
Output use type/rating PTC 2.5A Blade 3.0A PTC 2.5A Blade 3.0A
Output relays Form C (10A@12VDC)
Auxiliary inter ace output DPDT (1A@28VDC)
LEDs Status 4 (red, on when relay is energized) 8 (red, on when relay is energized)
Auxiliary Inter ace 1 (green on when auxiliary input is triggered, alarm condition)
Operating humidity 0~95%
Operating temperature -40°~167° F (-40°~75° C)
Dimensions 53/8"x35/8"x15/16" (136x92x23 mm) 8"x51/16"x15/16" (204x129x23 mm)
Weight 4.9-oz (140g) 4.8-oz (137g) 9.1-oz (257g) 8.9-oz (252g)
pecifications:
Overview:
Introduction:
Parts List:
Output
uses
Output Status
LEDS
Output 1
N.C., C., N.O., COM
Output 2
N.C., C., N.O., COM
Output 3
N.C., C., N.O., COM
Output 4
N.C., C., N.O., COM
Each output has
4 terminals
N.C., C., N.O., COM
Power input (required)
+
–
Control input (optional)
+
–
NC
C
NO
Auxiliary
Form C
dry outputs
Auxiliary Inter ace
Control Panel
INP
RET
T
–
+
–
+
For AC input
power supply,
cut jumper J3
In
GND
In
GND
In
GND
In
GND
IN
4
IN
3
IN
2
IN
1
Aux. Inter ace LED
Aux. Inter ace
Control DIP
Switches
ON
OFF
1 2 3 4
Cut Aux. Inter ace jumper or polarity reversal
input rom Aux. Inter ace (intact=wet, cut=dry)
For dual power
supply inputs, cut
jumpers J1 and J2
4-Output Boards
(PD-4BTQ shown)
AUX
INTERFACE
J1
J3
J2
Turn witch 1
-
4 ON to
deactivate AUX INTERFACE
Main use

ENFORCER Access Power Distribution Boards
SECO-LARM U.S.A., Inc. 3
Overview (Continued):
Terminal Overview:
Output
Fuses
8 Output Boards (PD-8BTQ shown)
Power input (required)
+
–
Control input (optional)
+
–
NC
C
NO
Auxiliary Inter ace
Control Panel
IN
P
RET
T
–
+
–
+
Auxiliary Form C
dry outputs
Output 1
N.C., C., N.O., COM
Output 2
N.C., C., N.O., COM
Output 3
N.C., C., N.O., COM
Output 4
N.C., C., N.O., COM
Each output has 4 terminals – N.C., C., N.O., COM
Output 5
N.C., C., N.O., COM
Output 6
N.C., C., N.O., COM
Output 7
N.C., C., N.O., COM
Output 8
N.C., C., N.O., COM
Output Status LEDS
Main use
Aux.
Inter ace
LED
Aux. Inter ace
control DIP
Switches
In
GND
In
GND
In
GND
In
GND
In
GND
In
GND
In
GND
In
GND
IN 4
IN
3
IN
2
IN
1
IN
8
IN
7
IN
6
IN
5
ON
ON
OFF
OFF
1 2 3 4
5 6 7 8
Cut Aux. Inter ace jumper or polarity
reversal input rom Aux. Inter ace
(intact=wet, cut=dry)
For AC input
power supply,
cut jumper J3
For dual power
supply inputs, cut
jumpers J1 and J2
AUX INTERFACE
J1
J3
J2
Turn w
itch 1
-
8 ON to
deactivate AUX INTERFACE
AUX OUTPUT
AUX INTERFACE
10A/250V
POWER CONTROL
Terminal Group
Terminal Labels
Description
of Use
or Function
Power +,
–
12~24 VAC/VDC Power supply (required)
Control +, –
Can be connected to a second 12~24 VAC/VDC power supply
or isolated operating power (optional)
Inputs (Trigger) └1┘~└4┘ (or ~└8┘*)
IN, GND
Inputs rom either N.O. or open collector sink inputs such as
RTE buttons, access control output relays, PIR sensors,
keypads, etc. Each input corresponds to the same numbered
output.
Outputs
└Output 1┘~└Output 4┘
(or ~└Output 8┘*)
NC, C, NO, COM
12~24 VAC/VDC trigger controlled outputs:
1. Fail-sa e devices to N.C. positive and COM negative,
2. Fail-secure devices to N.O. positive and COM negative,
3. Auxiliary output to C positive and COM negative,
NOTE :
•When using AC power input, polarity is not important.
•NC, C, and NO become Form C dry outputs
(5A@24VAC/VDC) when corresponding use is removed.
Auxiliary
Inter ace Control
Panel Inputs +, –, T, +, RET (–) Alarm trigger input (either N.C. or N.O.) rom Auxiliary Inter ace
Control Panel's output circuit (see Figs. 1~5, pg. 7)
Auxiliary
Inter ace Control
Panel Outputs
NO, C, NC Form C relay contact (1A@28VDC) or alarm reporting
*
PD-8PTQ and PD-8BTQ

ENFORCER Access Power Distribution Boards
4SECO-LARM U.S.A., Inc.
Installation Notes:
Installation:
1.
DIP Switches control whether an individual output should be triggered by the
auxiliary inter ace
(de ault is "OFF," not controlled).
2.
Using a single power supply:
a. I the power distribution board and the locking devices are powered with a single power
supply, connect the output to the positive and negative terminals marked "Power."
3.
When using two power supplies:
a. Cut the jumpers noted in the overview diagrams on pg. 2 or pg. 3.
b.
Connect the power or the power distribution board to the positive and negative terminals
marked "Control."
c. Connect the power or the locking devices to the positive and negative terminals marked
"Power."
NOTE :
•When using DC power supply, polarity must be observed.
•When using AC power supply, cut jumper J3.
4.
Each output can provide a switched power output, a Form C dry output, or both, as well as an
unswitched auxiliary power output. See the "Typical Application" on pg. 6.
Prior to installation, ensure that you are amiliar with the
various options and their requirements
noted in the "Overview," "Installation Notes," "Typical Application," and "Wiring Diagrams or
Various Auxiliary Inter ace Installations" sections.
1. Mount the board in a supply box, making sure to use compatible spacers between the board
and the metal back (see pg. 8 or ENFORCER Access Control Power Supply instructions).
2. Connect the main power supply to the power distribution board terminals marked "Power."
3. I using two power supplies, connect the second power supply to the power distribution board
terminals marked "Control" and cut the jumpers J1 and J2 as noted in the "Overview" section
above (pg. 2 or 4-output boards and pg. 3 or 8-output boards). Be sure not to cut jumper J3
unless using AC power supplies.
NOTE :
•When using DC power, be care ul to observe polarity when connecting power supplies.
•When using AC power, be sure to cut jumper J3.
•The input marked "Control" will only be used or a second power supply and never used
with a single power supply.
4. Connect each controlled device to one o the 4 or 8 outputs. Note the various connection
examples shown in the "Typical Application" section (see pg. 6).
a. Switched power outputs
i. Connect the negative input o the powered device to the terminal marked "COM."
ii. For ail-sa e operation, connect the positive input o the powered device to the
terminal marked "NC."
iii. For ail-secure operation, connect the positive input o the powered device to the
terminal marked "NO."
b. Dry Form C outputs
i. Remove the corresponding use or the output.
ii. Connect the negative input o the powered device directly to the negative input o the
power supply.

ENFORCER Access Power Distribution Boards
SECO-LARM U.S.A., Inc. 5
Installation (Continued):
iii.
Connect the power supply's positive terminal to the power distribution board output
terminal or this device marked "C."
iv. For ail-sa e operation, connect the positive input o the powered device to the
terminal marked "NC."
v. For ail-secure operation, connect the positive input o the powered device to the
terminal marked "NO."
c. Unswitched auxiliary power outputs (to provide power to card readers, keypads, etc.)
i. Connect the positive input o the powered device to the terminal marked "C."
ii. Connect the negative input o the powered device to the terminal marked "COM."
NOTE: Keep power limited wiring separated rom non-power limited wiring (AC input, battery
wiring) by a minimum distance o
1
/
4
" (7mm) and use separate knockouts in the
enclosure.
5. Connect each controlling device (card reader, keypad, RTE plate, etc.) to the corresponding
input terminal or the particular device to be controlled. Inputs are activated by normally open
or open collector sink inputs.
a. Normally open (N.O.) input triggers:
i. Connect the devices to the terminals marked "IN" and "GND" that correspond to the
power output terminals o the device to be controlled.
b. Open collector sink inputs:
i. Connect the access control panel open collector output to the power distribution
board's input terminal marked "IN."
ii. Connect the access control panel open collector's common (negative) to the power
distribution board's input terminal marked "GND."
6. Connect an Auxiliary Inter ace Control Panel (AICP) to the power distribution board's Aux.
Inter ace. A normally open, normally closed, or polarity reversal input rom an AICP signaling
circuit will trigger selected outputs. To enable AICP disconnect or any output, set the
corresponding DIP switch or that output to "ON." To disable AICP disconnect or any output,
set its corresponding DIP switch to "OFF" (de ault, "OFF").
a. Normally open (N.O.) input:
i. For a non-latching hookup, re er to the instructions or Fig. 1 on pg. 7.
ii. For a latching hookup, re er to the instructions or Fig. 4 on pg. 7.
b. Normally closed (N.C.) input:
i. For a non-latching hookup, re er to the instructions or Fig. 2 on pg. 7.
ii. For a latching hookup, re er to the instructions or Fig. 5 on pg. 7.
c. AICP signaling circuit input trigger
i. For a polarity reversal input rom the AICP Auxiliary Output, re er to the instructions
or Fig. 3 on pg. 7.
7. The AICP Auxiliary Output may also be connected as a dry orm C output as ollows:
a.
Connect the device to be triggered by the unit's dry contact output to the power distribution
board's Aux. Inter ace terminals as ollows:
i. For normally open output, connect to the terminals marked "NO" and "C."
ii. For normally closed output, connect to the terminals marked "NC" and "C."
NOTE:
The unit should be tested at least once a year or proper operation. Voltage on eac
h output
should be tested or both triggered and untriggered states and the operation o the AICP
must be simulated.

ENFORCER Access Power Distribution Boards
6SECO-LARM U.S.A., Inc.
Typical Application:
NC
C
NO
COM
NOTE: Corresponding use must be
removed or this installation
+
–
+
–
NC
C
NO
Auxiliary
inter ace
control panel
NO C NC
INP
RET
T
–
+
–
+
Jumpers J1 and J2 cut or
dual power supply inputs
2
Access
control panel
output relay
NC NO C
Keypad
–
+
NO COM
RTE
Plate
NO COM
DC Access
control power
supply
DC Access
control power
supply
(optional)
Control
Power
In
G
ND
In
G
ND
In
G
ND
Electric
strike
( ail-
secure)
Electromagnetic
door holder
Mag. lock
( ail-sa e)
Mag. lock
( ail-sa e,
orm C)
NC
C
NO
COM
NC
C
NO
COM
NC
C
NO
COM
1 3 4
2 1 3 4
–
+
+
–
4
PD-4BTQ shown
3
2 1
1.
In this example, each input is activated by
an N.O
.
trigger input.
Controlling devices' (keypads,
RTE plates, card readers, etc.) outputs are connected to the "In" and the "GND."
2. Switched devices (outputs 1~4) include both ail-sa e and ail-secure examples.
3. A keypad is connected both to control the
electric strike, but also to the "C" and "COM" outputs
or auxiliary power.
4. Output 3 is triggered by the Auxiliary Inter ace (Controlled by the Aux. Inter ace DIP switches).
5. Output 4 is an example o a Form C dry contact installation. For this application, the
corresponding use has been removed.
6. A single power supply must be connected to the power inputs marked "Power."
7. When using two power supplies, the second is connected to the two power inputs marked
"Control." In this case, the two jumpers J1 and J2 marked above must also be cut.
8. In this example, the Auxiliary Inter ace's N.O. (or N.C. or normally closed installations) and C
outputs are connected as Form C dry contacts (see pg. 7 or other options).
Output 4
use
removed
ON
OFF
1 2
3 4
AUX INTERFACE
J1
J3
J2
–
+
–
+
+
–
+
–
Output 3 DIP
switch is "ON"

ENFORCER Access Power Distribution Boards
SECO-LARM U.S.A., Inc. 7
Wiring Diagrams for Various Auxiliary Interface Installations:
Fig. 2
N.C. Trigger
Input
INP
RET
NC
C
NO
T
–
+
–
+
Fig. 1
N.O. Trigger
Input
INP
RET
NC
C
NO
T
–
+
–
+
Fig. 3
INP
RET
NC
C
NO
T
–
+
–
+
Auxiliary Control
Circuit EOL
Cut Aux
Inter ace jumper
(intact=wet,
cut=dry)
–
+
ACP
From Auxiliary
Control Circuit
Fig. 4
INP
RET
NC
C
NO
T
–
+
–
+
N.C.
Reset
Switch
N.
O
.
Trigger
Input
Fig. 5
INP
RET
NC
C
NO
T
–
+
–
+
N.
C
.
Trigger
Input
N.O
.
Reset
Switch
1.
For
normally open,
non-latching Auxiliary Inter ace
Control Panel (AICP) input,
connect an N.O. trigger to the
"T" and "INP +" Aux. Inter ace
terminals (see Fig. 1).
2. For normally closed,
non-latching AICP input,
connect an N.C. trigger to the
"T" and "INP –" Aux Inter ace
terminals. Add a jumper
between the "T" and "INP +"
terminals (see Fig. 2).
3. For a polarity reversal input
rom the AICP output, connect
the "+" and "–" terminals rom
the AICP control circuit to the
two terminals "+ INP –"on the
Aux. Inter ace, observing
polarity. I an AICP control circuit
EOL is used, connect that to the
two terminals "+ RET –"
terminals on the Aux. Inter ace
(see Fig. 3). Cut the "Aux
Inter ace" jumper near the Aux
Inter ace (see the corresponding
"Overview" on pg. 2 or 3).
4. For a normally open, latching
AICP trigger input with reset,
connect an N.O. trigger input to
the "T" and "INP +" Aux
Inter ace terminals. Add a
jumper between the "C" and
"INP +" terminals. Connect an
N.C. reset switch to the "T" and
"N.O." terminals (see Fig. 4).
5. For a normally closed,
latching AICP trigger input with
reset, connect an N.C. trigger
input to the "C" and "INP –" Aux
Inter ace terminals. Add a
jumper between the "N.C." and
"INP +" terminals. Connect an
N.O. reset switch to the "T" and
" INP +" terminals (see Fig. 5).

ENFORCER Access Power Distribution Boards
8SECO-LARM U.S.A., Inc.
No DC output
•
Check whether the AC input voltage or backup battery voltage is
normal
Low DC voltage output
•
Check whether the output voltage setting is correct
•Check whether the AC input wattage is correct (see chart, pg. 3)
•I the battery is supplying power, check whether the battery voltage
is normal
•Check whether the power supply board is overloaded
No backup battery power
•
Check whether the battery voltage is normal or already discharged
•Check whether the master use has burned out
Installing in ENFORCER Access Control Power upply
:
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
™
PITSW1
Order Part# 764
-
042%
MI_PD
-
xxTQ
_190711.docx
NOTICE
:
The SECO
-
LARM policy is one o continual development and improvement. For that reason, SECO
-
LARM
reserves the right to change speci ications without notice. SECO-LARM is also not responsible or misprints. All t
rademarks
are the property o SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A.,
Inc. All
rights reserved.
WARRANTY:
This SECO
-
LARM product is warranted against de ects in material and workmanship while used in normal
service or one (1) year rom the date o sale to the original customer. SECO-LARM’s obligation is limited to the
repair or
replacement o any de ective part i the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void i
damage is caused by or attributed to acts o God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or aulty installation, or i or any other reason SECO-
LARM determines that such equipment
is not operating properly as a result o causes other than de ects in material and workmanship.
The sole obligation o
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
’s
option. In no event shall SECO-
LARM be liable or any special, collateral, incidental, or consequential personal or property
damage o any kind to the purchaser or anyone else.
For installation in an
ENFOR
CER Access
Control Power Supply enclosure (see Fig. 6):
1. Place the APDB inside the enclosure to
note which our mounting holes match.
2. From the back side o the enclosure,
insert the our nylon mounting spacers
(included) through the our holes
indicated in step 1, pressing them in
irmly until you hear the click o the
enclosure mounting spring lock.
3. Align the our holes in the APDB to the
nylon mounting spacers and press irmly
until you hear the click o the board
mounting spring lock.
Connect the APDB power input to the power
supply circuit board's DC output terminal
according to the wiring diagram on pg. 6.
Fig. 6
Nylon mounting spacers
Mounting holes
Board mounting spring lock
Enclosure mounting spring lock
ENFORCER
E
AP
-
5D1Q shown