ENFORCER CCD BULLET CAMERA Manual ENFORCER CCD BULLET CAMERA Manual
Dimensions:
To BNC
(From DC Camera) (EVA-F5521-3)
(3-ft. wire length)
EVA-F5521-3
--
Optional power cord. For easy
connection of dome or bullet camera to power supply.
6” (153mm)
A
B
C
Parts List
1 x Bullet camera
1 x Mounting bracket
3 x Mounting screws
3 x Screw anchors
2 x Camera adjustment tools
1 x Manual
A. Camera
B. Bracket
C. DC jack
D. BNC connector (female)
E. Thumb screw
F. Adjustment plate
G. Mounting screws (3)
H. Screw anchors (3)
I. Moveable sunshield
J. Camera adjustment tools
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electricity limits.
3. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.
4. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted (if necessary).
2. Temporarily connect the camera to the 12VDC power supply.
3. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.
4. While watching the monitor, hold the camera bracket against the
wall by hand where it is to be mounted, then twist the camera
until it is certain that this mounting location is correct. Use a
pencil to mark the location of the three screw holes in the
bracket.
5. Disconnect the 12VDC power supply and video cable.
5. Do not open or disassemble the camera. There are no user-
serviceable parts inside.
6. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.
6. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use the three included screw anchors.
7. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.
8. Adjust the camera angle.
9. Tighten the bracket’s thumb screw so that the camera does not
move, but not so tight that it cracks the case or bracket.
10.Do a final test of the video camera and monitor.
* Note: Use the adjustment tools to tighten the thumbscrew and
the adjustment plate if needed, but do not overtighten.
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Automatic gain control
White balance
Power source
Power consumption
Storage temperature
Operating temperature
Dimensions (inc. cord mounting)
Weight
EV-1323CWP4 (NTSC)
Color bullet camera
1/3” CCD, Sony
420 TV lines
512 x 492 pixels
2:1 interlace
V: 59.94Hz, H: 15.734KHz
Internal
1V pp composite output, 75 ohms
F1.2, 4.3mm (lens included)
0.1 lux
0.45
>48dB
Auto Electronic Shutter (AES)
1/60~1/100,000 sec.
Auto
Auto
Auto
12VDC ±10%
125mA
-22°~140° F (-30°~60° C)
14°~113° F (-10°~45° C)
6” x 2” (153 x 50mm)
3.2 oz. (90g)
Specifications
D
G
H
E
F
I
43/
8” (109mm)
2” (50mm)
15/
16”
(24mm)
11/
16”
(26.5mm)
J
