SECO-LARM SLI ENFORCER VIDEO EV-1224C12 User manual

ENFORCER CCD DOME CAMERA Manual ENFORCER CCD DOME CAMERA Manual
ENFORCER
VIDEO
®
WARNING
●Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or electric shock. Do not open the
case of this device, as there are no field-serviceable components inside.
●
This product was designed for indoor use only. Mounting outdoors or exposure to rain or moisture could cause a dangerous electric shock,
damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one
of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2004 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
WARRANTY
ENFORCER dome cameras are warranted against defects in material and workmanship while used in normal service for a
period of two (2) years from the date of sale to the original customer. Our obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use
of this product in violation of any current laws or statutes.
EV-1224C12
1/4”CCD Color Dome Cameras
EV-1223B12
1/3”CCD B/W Dome Cameras
MANUAL
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®®
®®
®
• Check that the dome camera is powered up.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.
• Clean the lens (using a soft, clean cloth).
• Check that the light source is adequate.
• Clean the dome (using a soft, clean cloth).
• Adjust the monitor’s contrast knob.
• Change the position of the camera
• Change the position of the camera
• Change the position of the camera
• Check that the correct power supply is in use.
The screen is blank
The screen image is dim
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot
TROUBLE SHOOTING
file: DOME_IMUb.pmd
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: sales
@ seco-larm.com
PITFW1
®

ENFORCER CCD DOME CAMERA Manual ENFORCER CCD DOME CAMERA Manual
SIDE VIEW BOTTOM VIEW
Dimensions
Parts List
1 x Dome camera
4 x Mounting screws
1 x Manual
Camera
Dome
Window
Base
DC Jack
BNC(F) Connector
Support
Specifications
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens mount
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Gain control
Power source
Power consumption
Ambient temperature
Relative humidity
Dimensions
Weight
EV-1223B12 (EIA)
B/W camera
1/3” CCD, Sharp
400 TV lines
512 x 492 pixels
2:1 interlace
V: 60Hz, H: 15.734KHz
Internal
1V pp composite output, 75 ohms
F3.6mm (lens included)
0.08 lux
0.45
48dB
Auto Electronic Shutter (AES)
1/60~1/100,000 sec.
N/A
N/A
12VDC ± 10%
1.6W (max.)
14°~122° F (-10°~50° C)
30 - 90%
31/2” x 21/4” (88 x 57mm)
4.2 oz. (118g)
EV-1224C12 (NTSC)
Color camera
1/4” CCD, Panasonic
330 TV lines
510 x 492 pixels
2:1 interlace
V: 60Hz, H: 15.734KHz
Internal
1V pp composite output, 75 ohms
F3.6mm (lens included)
1.8 lux
0.45
46dB
Auto Electronic Shutter (AES)
1/60~1/100,000 sec.
N/A
N/A
12VDC ± 10%
1.5W (max.)
14°~122° F (-10°~50° C)
30 - 90%
31/2” x 21/4” (88 x 57mm)
4.2 oz. (118g)
BEFORE STARTING
1. This product was designed for indoor use only. Do not mount
the CCTV camera where it is exposed to rain or other moisture,
or in humid or dusty places.
2. Do not point the CCTV camera at the sun. Heat could damage
the camera, even when not in use.
3. Do not mount the CCTV camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.*
INSTALLATION
1. Remove the dome. Be careful not to scratch the dome. DO
NOT TOUCH ANY OF THE COMPONENTS INSIDE THE DOME.
2. Connect the camera to a video monitor via the video cable.
3. Temporarily connect the camera to a 12VDC power source.
4. Hold the base of the dome camera with your hand against the
ceiling, and try various locations and angles while watching
the video monitor to find the location which offers the best
protection. Mark that location with a pencil.
5. Run a hidden, permanent video cable from the monitor to the
mounting location.
6. Run a hidden cable from a 12VDC power supply to the
mounting location.
7. Connect the two cables to the dome camera.
8. Mount the base to the ceiling at the selected location
with the four mounting screws.
9. Make any necessary adjustments to the horizontal and
vertical angles of the camera itself while checking the
image in the video monitor.
10. Replace the dome, taking care not to touch the camera
or scratch the dome.
11. Test the camera again under the exact lighting
conditions under which it is expected to be used.
4. Do not open or disassemble the camera. There are no
user-serviceable parts inside.
5. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromag-
netic fields close to the display CRT, especially when the
monitor is turned on or during de-Gaussing, which
occurs automatically with many monitors when the
monitor is turned on.
Important:
Do not cut DC jack.
Use SECO-LARM’s
optional EVA-F5521-3
Pigtail Connector for
easy installation and
serviceability.
31 /2” (88mm)
21/4” (57mm)
31 /2” (88mm)