Seconique Lisbon User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 8
LISBON 3 DRAWER DRESSING TABLE
SEC/WG/10/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

NB ( 0.35 )
VD ( 0.55 )
NB
VD
PAGE 2 OF 8
SEC/WG/10/16/EU1
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
( SCREWDRIVER NOT PROVIDED )
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
CAM LOCK IS POINTING TOWARD THE HOLE ON EDGE OF PANEL. )
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK.YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 8
SEC/WG/10/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS LIST PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RIGHT SIDE PANEL
SUPPORT PANEL
TOP FRONT CROSSBAR
TOP BACK CROSSBAR
BOTTOM BACK CROSSBAR
BOTTOM FRONT CROSSBAR
DRAWER BACK
DRAWER SIDE - LEFT
LEFT BACK PANEL
DRAWER SIDE - RIGHT
DRAWER FRONT
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
3 PCS
3 PCS
3 PCS
3 PCS
CENTRE PANEL
LEFT SIDE PANEL
TOP PANEL
15 DRAWER BASE 3 PCS
1
2
3
4
9
8
7
5
6
12
10
14
11
13
15

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 4 OF 8
SEC/WG/10/16/EU1
HARDWARE LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
N
32 PCS
5 PCS
2 PCS
24 PCS
23 PCS
12 PCS
3 PCS
6 PCS
6 PCS
6 PCS
30 PCS
12 SETS
6 PCS
3 PCSDOWEL 6 X 30MM
BOLT M6 X 50MM
BOLT M7 X 60MM
SCREW M3.5 X 16MM
TACK
SCREW M4 X 38MM
HANDLE
DRAWER RUNNER A
DRAWER RUNNER B
HANDLE SCREW 19MM
SCREW M3.5 X 12MM
CAM BOLT + LOCK
PLASTIC FOOT
SCREW M4 X 50MM
O ALLEN KEY 1 PC
P
Q
ANTI - TIP STRAP
SCREW M4 X 16MM
2 PCS
2 PCS

PP ( 0.1 )
UH ( 0.3 )
UM ( 0.15 )
UN ( 0.26 )
UP ( 0.3 )
UY ( 0.4 )
VB ( 0.15 )
PP
UG
UH
UM
UN
UP
UY VB
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 5 OF 8
SEC/WG/10/16/EU1
STEP 1 STEP 2
YOU WILL NEED:- YOU WILL NEED:-
A
H
K
20 PCS
6 PCS
24 PCS
B
C
2 PCS
1 PC
N3 PCS
A
L 6 SETS
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER
A
L
L
C
O
B
O
O1 PC
FRONT BACK
FIRST HOLE
LAST THIRD HOLE
LARGE HOLE
SMALL HOLE
K
H
N
4
8
1
2
3
5
6
7
9
1
2
3
4
3
4
UP SECOND HOLE

RF ( 0.17 )
TA ( 0.08 )
TB ( 0.09 )
TC ( 0.052 )
TD ( 0.17 )
UD ( 0.14 )
UE ( 0.15 )
UF ( 0.18 )
UR ( 0.3 )
UT ( 0.23 )
UU ( 0.13 )
UV ( 0.18 )
RE
RFRH
RJ
TA
TB
TC
TD
UD
UE
UF
UR
UT UU
UV
UW
VC
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 6 OF 8
SEC/WG/10/16/EU1
STEP 3 STEP 4.1
PLEASE INSERT THE BACK PANEL INTO THE UNIT
YOU WILL NEED:-
B3 PCS
YOU WILL NEED:-
D6 PCS
D
K
W
J
L
14
E14 PCS
BACK SIDE VIEW Y
Y
Y
X
1
7
D
C
O
1 PC
1 PC
SHOULD READ-ADJUST SCREWS AS SHOWN
TO ALIGN DOOR ONCE HINGES HAVE BEED
ATTACHED.
V
D
NH
N
K
M
6 PCS
6 PCS
STEP 4.2
THE HEAD OF THE CAM BOLT
GOES INTO THE WIDE MOUTH
OF THE CAM LOCK.YOU THEN
TURN THE CAM LOCK SO THE
NARROW PART CLOSES OVER
THE CAM BOLT.
C
O
B
O
L
L
L
E
K
M
4
2
1
3
5
6
8
10
10 10
9
1 & 8
D
7
5
8
1
2
3
4
7
6
8
9

PC ( 0.07 )
PD ( 0.13 )
PE ( 0.15 )
PF ( 0.15 )
PK ( 0.18 )
RP ( 0.13 )
TF ( 0.08 )
TG ( 0.13 )
TH ( 0.13 )
TJ ( 0.1 )
TK ( 0.15 )
TL ( 0.15 )
TM ( 0.13 )
TN ( 0.15 )
TP ( 0.15 )
TR ( 0.12 )
PCPD
PE
PF
PK
RP
TF
TG
TH
TJ
TK
TL
TM
TN
TP
TR CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 7 OF 8
SEC/WG/10/16/EU1
STEP 5.1 STEP 6
A 12 PCS
YOU WILL NEED:-
D
E
F
18 PCS
12 PCS
9 PCS
THE HEAD OF THE CAM BOLT
GOES INTO THE WIDE MOUTH
OF THE CAM LOCK.YOU THEN
TURN THE CAM LOCK SO THE
NARROW PART CLOSES OVER
THE CAM BOLT.
G
I
J
3 PCS
6 PCS
6 PCS
STEP 5.2
STEP 5.3
STEP 5.4
STEP 5.5
F
ID
J
L
L
12&13
12&13
14
15
11
W
L 6 SETS
Q
A
A
D
E
F
Q
R
V
A
3 X DRAWERS
13
11 12
14
15
14
A
E
G
I
I

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 8 OF 8
SEC/WG/10/16/EU1
WARNING
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
HARDWARE LIST
( P ) Anti-Tip Strap - 2 pc
( Q ) M4 X 16MM - 2 pc
TOP
WALL
TOP
WALL
TOP
P
P
Q

SEC/SH/09/19/EU1
!
DO NOT
USE
LISBON DRESSING TABLE MIRROR
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
FOR DOMESTIC USE ONLY
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE. DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
PAGE 1

1
2
3
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PART LIST
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START ASSEMBLING. IF
YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY, PLEASE CONTACT
YOUR SUPPLIER IMMEDIATELY.
PARTS LIST
1PC
BOTTOM PANEL
SIDE PANEL
MIRROR PANEL
2PCS
1PC
1
HARDWARE LIST
A
B
BOLT 7x60MM 4 PCS
2 PCS
SEC/SH/09/19/EU1
2
2
3
C1 PC
ALLEN KEY
SCREW
PAGE 2

HARDWARE NEEDED:
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
A4PCS
SEC/SH/09/19/EU1
STEP 1 STEP 2
A
C
C1PC
STEP 2.1
HARDWARE NEEDED:
B2PCS
1
2
2
2
1
B
2 3
B
3
2
2
1
PAGE 3