Seconique NEVADA SLIDING DOOR BEDSIDE User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
FOR DOMESTIC USE ONLY
PAGE 01
DO NOT USE
!
SEC/SH/12/21/CA1
NEVADA SLIDING DOOR BEDSIDE
GREY GLOSS/LOEV

PARTS LIST
Please Note:
The below parts have all been stamped with the part number to help identify them during assembly.
PAGE 02
TOOLS REQUIRED
01
03
04
06
07
07
09
02
05
08
10
11
1
6
3
5
11
4
2
9
710
7
8
SEC/SH/12/21/CA1
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
S100-103-082-CA1-01 Top Panel 11/1
Right Side Panel
Le Side Panel
Shelf
Sliding Door
Back Panel
Drawer Side
Drawer Front
Drawer Back Panel
Drawer Boom
Front Baseboard
S100-103-082-CA1-02
S100-103-082-CA1-03
S100-103-082-CA1-04
S100-103-082-CA1-05
S100-103-082-CA1-06
S100-103-082-CA1-07
S100-103-082-CA1-08
S100-103-082-CA1-09
S100-103-082-CA1-10
S100-103-082-CA1-11
1
1
1
1
1
2
1
1
1
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1

PAGE 03
FITTINGS LIST
ABC
E F
G H IJ
KLM
Cam Bolt (6x)
Flan Head Screw
Ø4,0 x 22mm (4x)
Flat Head Screw
Ø4,0 x 50mm (8x) Dowel Ø6,0 x 30mm (20x) Nail 10 x 10 (22x)
Cam Nut Ø12mm (2x) Plastic Foot (4x) Hole Plugs (14x)
Glue (1x) Handle (2x)
N
Cam Nut Ø15mm (4x)
1/+ 1/+
2/+
2/+
2/+
1/+
1/+ 1/+ 1/+
1/+
2/+
TIPS FOR FITTINGS CAM-LOCKS
Cam bolt head needs to be in centre
PO
WHEN FITTING CAM NUT. ENSURE STARTING
POSITION IS CORRECT BEFORE YOU INSERT
CONNECTING CAM BOLT TURN CLOCKWISE UNTIL
SECURE
CORRECT WRONG
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside) Shoulder
Panel
P
Panel
O
O
Flat Head Screw
Ø6,0 x 10mm (4x)
Flat Head Screw
Ø4,0 x 14mm (6x)
Flan Head Screw
Ø4,0 x 14mm (12x)
2/+
P
D
Drawer Runners (1x)
Q
Sliding Door Castor(2x)
Spring top guide(2x)
R
Plastic Rail (2x)
SEC/SH/12/21/CA1

2 - x1
RIGHT SIDE PANEL
PAGE 04
TOOLS REQUIRED
HARDWARE REQUIRED
E+K
Detail 1
PARTS REQUIRED
F
I
Detail 4
K01
E02
Ø6,0 x 30mm
I02
F02
10 x 10
Detail 4
Detail 1
Detail 4
Detail 1
02
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
K01
E02
STEP 1
STEP 2
Ø6,0 x 30mm
E+K
Detail 1 F
I
Detail 4
I02
F02
10 x 10
3 - x1
LEFT SIDE PANEL
Detail 1
Detail 1
Detail 4
Detail 4
3
SEC/SH/12/21/CA1

TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
B01
A02
PAGE 05
STEP 3
STEP 4
3 - x1
LEFT SIDE PANEL
SECOND HOLE
THIRD HOLE
LAST FIFTH HOLE Detail 5
Q
AB
SECOND HOLE
THIRD HOLE
LAST FIFTH HOLE Detail 3
Q
A
B
Ø4,0 x 14mm
Ø6,0 x 10mm
Q01
LEFT
PLEASE NOTE
PRE-DRILLED
HOLES.
PLEASE NOTE
PRE-DRILLED
HOLES.
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
B01
A02
2 - x1
RIGHT SIDE PANEL
Ø4,0 x 14mm
Ø6,0 x 10mm
Q01
RIGHT
Detail 5
Detail 5
Detail 3
Detail 3 3
2
PLEASE NOTE
PRE-DRILLED
HOLES.
PLEASE NOTE
PRE-DRILLED
HOLES.
SEC/SH/12/21/CA1