Seconique NEVADA User manual

NEVADA 3 DRAWER BEDSIDE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
PAGE 1
FOR DOMESTIC USE ONLY
SEC/SH/01/20/CA3

6x1
8x3
Drawer Back Panel
9x3
Back Panel
10 x3
7x6
Drawer Front
2x1
Drawer Bottom
1x1
Drawer Side
4x1
Right Side Panel
3x1
Left Side Panel
5x1
Front Baseboard
Back Baseboard
Top Panel
6
8
9
10
7
1
2
4
3
5
7
PAGE 2
PARTS LIST
Please Note:
The below parts have all been stamped with the part number to help identify them during assembly.
* Use of power tools to assemble this product will invalidate any claim and damage this
product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
!
9
If you wish, after assembly, use a
rubber to erase part number "9".
SEC/SH/01/20/CA3

FITTINGS LIST
ABCD
E F G H
I J K L
M
Drawer Runners (3x)
Cam Bolt (10x)
USE
DO NOT
USE
!
TIPS FOR FITTINGS CAM-LOCKS
PO
P
O
WHEN FITTING CAM NUT. ENSURE STARTING
POSITION IS CORRECT BEFORE YOU INSERT
CONNECTING CAM BOLT TURN CLOCKWISE UNTIL
SECURE
CORRECT WRONG
Cam bolt head needs to be in centre
CAMBOLT
Tighten until shoulder in flush with
panel. Do not overtighten or
undertighten (see example below) Shoulder
Panel Panel
Flat Head Screw
Ø6,0 x 10mm (12x)
Flat Head Screw
Ø4,0 x 14mm (18x)
Flan Head Screw
Ø4,0 x 20mm (6x)
Flat Head Screw
Ø4,0 x 50mm (10x)
Dowel Ø6,0 x 30mm (36x) Nail 10 x 10 (42x) Cam Nut Ø12mm (6x)
Plastic Foot (4x) Hole Plugs (10x) Glue (1x) Handle (3x)
Glue
N
Cam Nut Ø15mm (4x)
PAGE 3
SEC/SH/01/20/CA3

Detail 1
Detail 5
2
Detail 1
Detail 4
Detail 4
Detail 5
Pre-Assembly
M-Drawer
Runners (3x)
Glue
K-Glue
A-Flat Head Screw
Ø6,0 x 10mm (12x)
E-Dowel
Ø6,0 x 30mm (36x) F-Nail 10 x 10 (4x) I-Plastic Foot (4x)
Detail 1
E+K
Detail 4Detail 3
F
I
M
A
B
Detail 5
M
A
B
Detail 2
G
G-Cam Bolt (10x)
B-Flat Head Screw
Ø4,0 x 14mm (6x)
Detail 1
Detail 4
Detail 3
1
Detail 1
Detail 4
Detail 3
PAGE 4
UP SECOND HOLE
SECOND HOLE
LAST FIFTH HOLE
M
3x
3x
9
8
Detail 2
Detail 2
Detail 1
Detail 1
5
7
Detail 1
Detail 2
Detail 2
Detail 2
Detail 2
6x
Detail 1
Detail 1
3
4
SEC/SH/01/20/CA3

2
N-Cam Nut (4x)
Detail 7
Detail 7
N
5
Glue
K-Glue
Detail 1
E+K
Detail 1
PAGE 5
Detail 7
2
1
Detail 1
E+K
1
D-Flat Head Screw
Ø4,0 x 50mm (4x)
Detail 6
D
Detail 6
2
1
4
3
Glue
K-Glue
Detail 1
Detail 6
Detail 6
Detail 6
Detail 1
SEC/SH/01/20/CA3

4
F-Nail 10 x 10 (24x) H-Cam Nut (6x) J-Hole Plugs (6x)
Glue
K-Glue
D-Flat Head Screw
Ø4,0 x 50mm (6x)
3x
1º 3x 2º
3x
3º
D
Detail 9
D
9
7
7
8
Detail 9
Detail 1
Detail 1
Detail 1
6
3
F-Nail 10 x 10 (14x)
Detail 8
F
PAGE 6
Detail 1
E+K
Detail 9
JH
Detail 10
Detail 8
F
F
FFF
10
Detail 10
Y
Y
X
F
X=117mm
Y=43mm
90mm
6mm
F
P
O
P
6 6
O
10 2
TIPS FOR FIXING
DRAWER BOTTONS
Y
FX
Y
SEC/SH/01/20/CA3

L-Handle (3x)
C-Flan Head Screw
Ø4,0 x 20mm (6x)
PAGE 7
6
Detail 11
J-Hole Plugs (4x)
J
Detail 11
5
3x
5º
3x
4º
FIRST HOLE LAST SECOND HOLE
M
M
B
L
C
C
B
B
B
M
B Flat Head Screw-
Ø4,0 x 14mm (12x)
M-Drawer
Runners (3x)
SEC/SH/01/20/CA3