Seconique CORONA 4 DRAWER DRESSING TABLE User manual

CORONA 4 DRAWER DRESSING TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SH/09/22/PJ1
FOR DOMESTIC USE ONLY
Page 01
55522

SEC/SH/09/22/PJ1
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
12
13
S100-105-006-PJ1-01 Top Panel 1
Right Side Panel
Le Side Panel
Centre Panel
Foot
Front Crossbeam
Back Support Bar
Internal Front Crossbeam
Internal Back Crossbeam
Drawer Runner
Front Plinth
Side Plinth
Back Panel
S100-105-006-PJ1-02
S100-105-006-PJ1-03
S100-105-006-PJ1-04
S100-105-006-PJ1-05
S100-105-006-PJ1-06
S100-105-006-PJ1-07
S100-105-006-PJ1-08
S100-105-006-PJ1-09
S100-105-006-PJ1-10
S100-105-006-PJ1-11
S100-105-006-PJ1-12
S100-105-006-PJ1-13
1
1
1
1
1
1
1
1
8
1
2
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Page 02
PARTS LIST
1/1
( 2x )
14
15
16
17
18
19
20
Small Drawer Front
Small Drawer Side
Drawer Base
Small Drawer Back
Medium Drawer Front
Medium Drawer Side
Medium Drawer Back
S100-105-006-PJ1-14
S100-105-006-PJ1-15
S100-105-006-PJ1-16
S100-105-006-PJ1-17
S100-105-006-PJ1-18
S100-105-006-PJ1-19
S100-105-006-PJ1-20
1
2
4
1
2
4
2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
21
22
23
Large Drawer Front
Large Drawer Side
Large Drawer Back
S100-105-006-PJ1-21
S100-105-006-PJ1-22
S100-105-006-PJ1-23
1
2
1
1/1
1/1
1/1
1
12
15 17
14 15
21 22
19
19
22
18
13
11
8
5
2
7
12
4
6
9
10
10
10
10
10
10
10
10
Please Note:
The below Highlighted parts have all been stamped with the part number to help identify them during assembly.
16
16
23
20
3

SEC/SH/09/22/PJ1
FITTINGS
TOOLS REQUIRED
Page 03
FITTINGS
G14
24
32
F16
16 H03
A
B
C
(+2)
(+2)
(+2)
(+2)
2x
1x
1x
(+2)
10x10
3,5x16
3,0x30
3,0x20 4,0x45
Ø8x30
Ø8x20
3,5x35
J01
04
24
I04
D
E(+2) (+)
(+1)
(+1)
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.

E02
Ø 8 x 30mm
C06
3,0x20
SEC/SH/09/22/PJ1
Page 04
3 - x1
LEFT SIDE PANEL
STEP 2
PARTS REQUIRED
STEP 1
6 - x1
FRONT CROSSBEAM
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
E16
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Ø 8 x 20mm
E
E
(8x) F
F
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
F
10 9
8
7
6
7 - x1
BACK SUPPORT BAR
8 - x1
INTERNAL FRONT CROSSBEAM
9 - x1
INTERNAL BACK CROSSBEAM
10 - x8
DRAWER RUNNER
F16
Ø 8 x 30mm
C
C
C
C
C
C
E
E
3
10 - x3
DRAWER RUNNER
10
10
10

SEC/SH/09/22/PJ1
Page 05
2 - x1
RIGHT SIDE PANEL
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 3
Please assemble on
a clean soft surface
to avoid damage.
E02
Ø 8 x 30mm
C06
3,0x20
4 - x1
CENTRE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
E
C
10 - x3
DRAWER RUNNER
E
E
C
C
C
C
C
4
10 10 10
E
E
E
E
E
2
E04
Ø 8 x 30mm

A03
3,5x35
SEC/SH/09/22/PJ1
Page 06
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 5
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
1 - x1
TOP PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
2 -
x1
RIGHT SIDE PANEL
5 - x1
FOOT
6 -
x1
FRONT CROSSBEAM
A08
A
H
A
6
2
1
A
A
A
HH
5
A
A
A
A
A
AA
A
4 - x1
CENTRE PANEL
7 -
x1
BACK SUPPORT BAR
3,5x35
H03
4,0x45
4
7

SEC/SH/09/22/PJ1
Page 07
10 - x2
DRAWER RUNNER
STEP 8
PARTS REQUIRED
HARDWARE REQUIRED
STEP 7
3 - x1
LEFT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
8 - x1
INTERNAL FRONT CROSSBEAM
11 - x1
FRONT PLINTH
TOOLS REQUIRED
9 - x1
INTERNAL BACK CROSSBEAM
A07
3,5x35
A
A
3
8
9
AA
C
12 - x2
SIDE PLINTH
C04
3,0x20
A06
3,5x35
12
12
11
10
A
A
A
A
A
A

G14
SEC/SH/09/22/PJ1
Page 08
STEP 10
PARTS REQUIRED
STEP 9
13 - x1
BACK PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
TOOLS REQUIRED
HARDWARE REQUIRED
I
( 1x )
B
B
B
D
G
13
I04
10x10
3,5x16
14 - x1
SMALL DRAWER FRONT
15 - x2
SMALL DRAWER SIDE
16 - x1
DRAWER BASE
17 - x1
SMALL DRAWER BACK
D01
B08
3,0x30
D
14
B
15
17
15
16
B
B
B
B
Please assemble on
a clean soft surface
to avoid damage.
XXXXX
For your future reference
order number should be here
III
G
G
G
G
G
G
G
G
G
G
G
G
G

SEC/SH/09/22/PJ1
Page 09
STEP 11
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
16 - x2
DRAWER BASE
18 - x2
MEDIUM DRAWER FRONT
19 - x4
MEDIUM DRAWER SIDE
20 - x2
MEDIUM DRAWER BACK
D02
B16
3,0x30
( 2x )
B
B
D
D
B
B
B
B
B
B
16
19
19
18
20
( 1x )
STEP 12
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
16 - x1
DRAWER BASE
21 - x1
LARGE DRAWER FRONT
22 - x2
LARGE DRAWER SIDE
23 - x1
LARGE DRAWER BACK
D01
B08
3,0x30
D
D
22
23
16
B
B
B
B
22
21
B
B
B
B
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.

SEC/SH/09/22/PJ1
Page 10
STEP 14
PARTS REQUIRED
STEP 13
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Serious or fatal injuries can occur from furniture tipping
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.
Please make sure you use fixings suitable for the walls in your home.
Wall
Top
Top
Wall Top
TOOLS REQUIRED
HARDWARE REQUIRED
( 2x )
J01
2x
1x
1x