Seconique BERGEN User manual

1
BERGEN 2 DOOR 2 DRAWER SIDEBOARD
OAK EFFECT/WHITE/GREY
ASSEMBLY INSTRUCTIONS
_ _ _ _ _HN
_ _ _ _ _HN
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• Never drag or push products as this could cause damage to the joints making it inferior.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Do not place this product next to a radiator or in direct sunlight.
• Do not drag or push items across your high gloss furniture as this may cause the surface to scratch.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack if subjected to heat.
Therefore it is recommended that room temperature is maintained, with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking will occur.
• For general cleaning use a soft cotton or micro fibre cloth, and do not use detergents of any kind.
• From time to time it may be necessary to tighten fittings, regular inspections should be carried out.
• Do not place on a wet or damp floor as staining may occur to your floor.
SEC/AY/12/19/HN1
SEC/AY/08/20/HN2

*Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe!!!
*Please assemble on a clean soft suface to avoid damage.
*Please check contents and read the instructions before commencing assembly.
*Assemble this product following the enclosed instructions carefully.
*Please take care to avoid damaging panels during assembly.
Please Note:
The below parts have all been stamped with the
part number to help identify them during assembly.
PARTS LIST
01
02 03 04
05
06
07
07
08
09 10
11 12
13
13
14
15
Part Number Part Code Part Description Quantity
01 Base Panel x1
02 Left Side Panel x1
03 Shelf Panel x1
04 Division Panel x1
05 Fixed Shelf x1
06 Right Side Panel x1
07 Back Panel x2
08 Top Panel x1
09 Left Door x1
10 Right door x1
11 Drawer Front x1
12 Lower Drawer Front x1
13 Drawer Side x4
14 Drawer Bottom x2
15 Drawer Back Panel x2
2
ITM/S304-
SEC/AY/12/19/HN1
Part Code Part Number Part Description Quantity Carton
01
02
03
04
05
06
07
08
09
10
11
12
13
14
S 01400-405-032-HN2- Base Panel 1 1/2
Left Side Panel
Shelf Panel
Division Panel
Fixed Shelf
Right Side Panel
Back Panel
Top Panel
Left Door
Right Door
Drawer Front
Lower Drawer Front
Drawer Side
Drawer Bottom
S 0400-405-032-HN2- 2
S 0400-405-032-HN2- 3
S 0400-405-032-HN2- 4
S 0400-405-032-HN2- 5
S 0400-405-032-HN2- 6
S 0400-405-032-HN2- 7
S 0400-405-032-HN2- 8
S 0400-405-032-HN2- 9
S400-405-032-HN2-10
S 1400-405-032-HN2-1
S400-405-032-HN2-12
S400-405-032-HN2-13
S400-405-032-HN2-14
1
1
1
1
1
2
1
1
1
1
1
4
2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
2 2/
2 2/
2 2/
2 2/
1/2
1/2
15 S400-405-032-HN2-15 Drawer Back Panel 2 1/2
SEC/AY/08/20/HN2

3
ITM/S304-
FITTINGS LIST
TIPS FOR FITTINGS CAM-LOCKS
USE
DO NOT USE
When fitting cam nut. Ensure starting
position is correct before you insert
connecting cam bolt turn clockwise until
secure.
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside).
Shoulder
Panel Panel
Cam bolt head needs to be in centre
CORRECT WRONG
20x34x10x26xCDAB
02x
01x16x
L
OP
Drawer Runners
Glue Hole Plugs
04x
04xK
J
Hinge
12mm Hinge Plate
04x01x
MN
Metal Leg Adjustable Leg
!




+/3
+/1
13x10x13x
+/2
FEG
Cam Bolt +/2 Union screw 18mm
02x
Q04x
R
Washer
02x01x
ST
Strap Back Panel Strip
Flat Head Screw
O3,5x10mm
+/1 +/2
Flat Head Screw
O3,5x40mm Dowel O8x25mm
Flan Head Screw
O3,5x14mm
Cam Nut O15mm
Flan Head Screw
O3,0x20mm
SEC/AY/12/19/HN1
16x
I
Triangle support angle
16x
H
Flat Head Screw
O3,0x16mm
+/2
+/2 +/3
SEC/AY/08/20/HN2

Pre-Assembly
Detail 2 Detail 17 Detail 18 Detail 19
Detail 1
1
2
3
Detail 1
Detail 1
Detail 1
Detail 2
Detail 2
Detail 2
Detail 2
Detail 18
Detail 18
Detail 17
Detail 18
Perform the adjustment
of the leg (N) at the
moment of fixing it.
Detail 19 Detail 18
Detail 1
01
E
E
E
EE
MM
B
B
B
B
N
N
E
M
M
NM
M
EE
E
E
E
E
E
E
E
E
E
EE
B
BBB
B
B
B
B
B
B
E
E
E
E
E
E
4
ITM/S304-
10x
B04x01x MN
Metal Leg Adjustable Leg
10x
E
Union screw 18mm
Male
(Female)
Female
(Male)
(Male)
Flan Head Screw
O3,5x14mm
SEC/AY/12/19/HN1
SEC/AY/08/20/HN2

Pre-Assembly
Detail 6
Detail 6
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
Detail 3
02
03
05
Detail 3
D
O
Detail 6
J
BB
D
BB
BB
J
J
D
D
D
D
D
D
D
D
D
D
5
ITM/S304-
11x
04xDB O
Glue
02x
J
12 mm Hinge Plate
Dowel O8x25mm
Flan Head Screw
O3,5x14mm
PRE-DRILLED HOLE
SEC/AY/12/19/HN1
SEC/AY/08/20/HN2