Seconique PORTLAND User manual

IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF SERVICE IF YOU FOLLOW THE
GUIDELINES FOR ITS SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS PRODUCT. ITS USE WILL
INVALIDATE ANY CLAIM YOU MAY HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE NECESSARY TO TIGHTEN
UP THE FIXINGS FROM TIME TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXINGS.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET). DO NOT USE POLISH, DETERGENT
OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A PLACE MAT UNDER HOT OR
COLD ITEMS TO PREVENT MARKING.
FOR DOMESTIC USE ONLY
PAGE 1 OF 2
PORTLAND CHAIR
ASSEMBLY INSTRUCTIONS
DO NOT
USE
SEC/SH/08/18/PU1

PORTLAND CHAIR
ASSEMBLY INSTRUCTIONS
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START ASSEMBLING.
IF YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY. PLEASE
CONTACT YOUR SUPPLIER IMMEDIATELY.
HARDWARE LIST(FOR ONE CHAIR)
PARTS LIST(FOR ONE CHAIR)
NO.
1
2
3
4
5
QTY
1PC
2PCS
1PC
2PCS
1PC
DESCRIPTION
CHAIR BACK
SIDE STRETCHERS
BOTTOM STRETCHERS
FRONT SECTION
CUSHION SEAT
NO.
A
B
C
D
E
QTY
6PCS
6PCS
6PCS
8PCS
1PC
DESCRIPTION
M6 X 50MM JCBC BOLTS
M6 X 13.5MM SPRING WASHER
M6 X 13.5MM FLAT WASHER
M4 X 32MM SCREW
M4 X 30 X 115 ALLEN KEY BALL SHAPE
STEP 1
STEP 2
EAB
C
ABC
2Please Repeat
For Both Sides
E
2
2
D
D
4
Attach the Side Stretchers(2) to the Chair Back(1) with Bolt(A),
Spring Washer(B) and Flat Washer(C). Tighten up using Allen Key(E).
Next, insert the Bottom Stretcher(4) to Chair Back(1) with screw(D)
and use Phillips Screwdriver(Not Provided) to drive (D). Do not
tighten completely at this time.
Attach Front Section(3) to Side Stretchers(2) and Bottom
Stretchers(4). Fasten (3) to (2)with Bolt(A), Spring Washer(B)
and Flat Washer(C). Use Allen Key to tighten (A). Fasten (3) to (4)
with Screw(D) and use a Phillips Screwdriver (Not Provided) to
drive (D). Fully tighten all the bolts and screws.
Place the Cushion Seat(5) bottom- side up on an elevated
surface. Position the chair frame assembly with the legs
facing up as shown.
Centre the seat frame to the Cushion Seat(5). Use a Phillips
Screwdriver to drive screw(D) to fasten the seat to the Chair
Frame.
STEP 3
1
3
2
4
4
1
PAGE 2 OF 2
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE ANY CLAIM AND MAY
DAMAGE THIS PRODUCT MAKING IT UNSAFE.
4
4
3
3
5
1
D
D
PHILLIPS
SCREWDRIVER
2
4
111
5
SEC/SH/08/18/PU1