Securitytec SW-11Z-I1-V1 User manual

1
l
─DVR ─
User Manual
SW-11Z-I1-V1.0-E
This document contains preliminary information and subject to change without notice.

2
This symbol is intended to
alert the user to the presence
of unprotected “Dangerous
voltage" within the product's
enclosure that may be strong
enough to cause a risk of
electric shock.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
NOTE: This equipment has been tested
and found to comply with the limits for a
class digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference
in which case the user will be required to
correct the interference at his own expense.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
Notice: Ghosting or fractured images may occur on the screen when there is a suddenly surge
or lightning stroke which cause damage on IC in the DVRs.

3
Table of Contents
CHAPTER 1 MAIN MENU SETUP ____________________________________ 4
1-1 RECORD SETUP ____________________________________________ 5
1-1.1 Quality & Frame Rate Setup _____________________________ 6
1-2 EVENT SETUP ______________________________________________ 6
1-2.1 MOTION SETUP ________________________________________ 7
1-2.1.1 MOTION AREA SETUP______________________________ 7
1-2.2 SENSOR SETUP________________________________________ 8
1-3 SCHEDULE SETUP __________________________________________ 9
1-3.1 Schedule Record Setup _________________________________ 9
1-3.2 Holiday Setup _________________________________________ 10
1-4 CAMERA SETUP ___________________________________________ 10
1-5 ACCOUNT SETUP __________________________________________ 11
1-5.1 Permission Setup______________________________________ 11
1-5.2 User Picture Setup ____________________________________ 12
1-6 NETWORKING SETUP_______________________________________ 12
1-6.1 NETWORKING SETUP __________________________________ 13
1-6.1.1 DHCP ___________________________________________ 13
1-6.1.2 LAN_____________________________________________ 13
1-6.1.3 ADSL____________________________________________ 14
1-6.1.4 3G ______________________________________________ 14
1-6.2 HTTP Setup___________________________________________ 15
1-6.3 DDNS Setup __________________________________________ 16
1-6.4 Mail Setup ____________________________________________ 17
1-7 PTZ & RS485 SETUP _______________________________________ 18
1-8 SYSTEM SETUP____________________________________________ 19
1-8.1 DISPLAY SETUP_______________________________________ 19
1-8.2 DATE/TIME SETUP _____________________________________ 20
1-8.2.1 CHANGE DATE & TIME____________________________ 21
1-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP____ 21
1-8.2.3 INTERNET TIME SETUP ___________________________ 22
1-8.3 BUZZER & RELAY SETUP ______________________________ 22
1-8.4 SPOT SETUP__________________________________________ 23
1-9 UTILITY SETUP ____________________________________________ 24
1-10 DIAGNOSTIC______________________________________________ 25
CHAPTER 2 BACKUP & SEARCH___________________________________ 26
2-1 BACKUP SETUP____________________________________________ 26
2-2 SEARCH SETUP____________________________________________ 29
2-2.1 EVENT SEARCH_______________________________________ 29
2-2.1.1 CRITERIA SETUP FOR EVENT SEARCH _____________ 30
2-2.2 TIME SEARCH_________________________________________ 31
CHAPTER 3 Remote Software Installation and Setup ___________________ 32
3-1 AP Software Installation and instruction ______________________ 32
3-2 How to do remote monitoring through IE _____________________ 34
3-3 How to do remote monitoring through JPEG VIEWER(Only Monitor
Function) _____________________________________________________ 35
3-4 AP Software Operation______________________________________ 37
CHAPTER 4 Specification __________________________________________ 38

4
CHAPTER 1 MAIN MENU SETUP
To enter the main menu and set up DVR, log-in account and user password are required.
The default password of the administrator is “123456”. Please check the “Account Setup”for
related setup of other log-in users.
Table 1-0.1 Some definition of virtual keyboard.
Item
Description
Switch between capital and small letters.
/
Switch between numbers and letters.
Press to cancel the setup, and re-choose the login
account.
Delete the last character.
Enter to identify the password. It will enter the set
up menu, If the password is verified.
Space key

5
Table 1-0.2 The operation of remote control under the setting menu
Item
Description
Switch to different options under one item
Switch to different items
MENU
Save setup and back to LIVE mode
ESC
Back to Upper level of menu without saving
ENTER
Enter the menu, or display virtual keyboard
PS. The initialization of new-installed HD is required before recording, please refer to “UTILITY
SETUP”for detail.
1-1 RECORD SETUP
Item
Description
HDD FULL
Select STOP to stop recording or OVERWRITE to reuse the
HDD when HDD is full
「Stop」： Stop Recording
「Overwrite」： Start to overwrite that begin from the oldest data
of HDD, and continue to record.
OSD position X
Setup OSD X axis
OSD position Y
Set up OSD y axis
OSD position setup
Set up OSD axis
Video Preservation
Setup the video preservation period. Recorded video will be
deleted automatically after expiry of preservation period.
Quality & Frame Rate
Setup
Setup the quality and frame rate for each channel under normal
recording and event recording type.
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.

6
1-1.1 Quality & Frame Rate Setup
Item
Description
Normal setup/
event setup
Select recording mode
Resolution
Select recording resolution: NTSC:352x240, 704x240, 704x480
PAL:352X288,704X288,704X576
Record Type
You can setup quality and FPS separately for record type.
No.
Check/uncheck the box enable/disable selected channel recording
Quality
Select quality: Below Basic/ Basic/ Normal/ High/ Highest
FPS
Select recording frame rate.
(The number of sheets in accordance with the actual models)
Auto
Assign each channel with its maximum accessible fps
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.
1-2 EVENT SETUP
Item
Description
Motion Setup
Enter to set up motion detection
Sensor Setup
Enter to set up sensor detection

7
1-2.1 MOTION SETUP
Item
Description
Alarm Duration(Seconds)
When motion detect，the number of seconds continuous alarm
1~16
You can setup independently for each channel.
Enable
Check the box to Enable/Disable motion detection for each channel.
Sensitivity
Drag the white bar or press ◀▶to set up Sensitivity from
value 0 to 10 for each channel. The higher value you set the
higher sensitivity it will be.
Motion Area Setup
Enter to setup motion detection area
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.
1-2.1.1 MOTION AREA SETUP
The motion detection has been divided into 22x18 grids. The default detection area is
full screen as it marked in transparent for local DVR and purple for remote access.
Areas deselected for motion detection are marked in red for both local and remote site.

8
Item
Description
Mask Mouse Selection
Switch between “select”and “deselect”for cursor-dragging function
All Area Detection
Select entire screen as detection area.
Mask All Area
Deselect entire detection area.
Continue
Continue setup
Exit & Save
Save setup and leave
Exit & Discard
Cancel setup and leave
1-2.2 SENSOR SETUP
Item
Description
Sensor Popup
Check the box to Enable/Disable popup screen function for all
channels. When Sensor is detected in LIVE mode, the detected
channel image will pop up in full screen display.
All Off
Set all sensor off
All Low
Set all sensor polarity low
All High
Set all sensor polarity high
Sensor Polarity
Click or press ▼to select between HIGH, LOW voltage for
triggering sensor detection or OFF to turn off polarity for each
channel
Low Polarity：Sensor has not been triggered. When connected,
sensor will be turned on..
High Polarity：Sensor has been triggered. When connected, sensor
status will be turned off..
Off ：Sensor is deactivated, and will not be turned on/off.
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.

9
1-3 SCHEDULE SETUP
Except from starting recording manually, you can also setup the recording time by weeks
and schedule including normal, motion detect, and recording type.
Item
Description
Page
Each page provides 10 schedules for setup. 5 pages in total.
Holiday Setup
Enter to setup holiday, up to 50 days, other than weekends,.
View Event/ Motion/
Sensor Setup
View Normal/ Motion/Sensor
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.
1-3.1 Schedule Record Setup
Click on the time on the left side. The setup menu will be displayed. You can have
detail setup by dates, Time and event.

10
1-3.2 Holiday Setup
Since holidays are different by different country and region, you can setup the holiday of
your location accordingly.
1-4 CAMERA SETUP
Item
Description
1~16
You can setup independently for each channel.
Mask
Check the box to Enable/Disable mask function for LIVE mode
Sharpness
Drag the bar or press ◀▶to adjust Sharpness of your camera from value 0 to 15.
Brightness
Drag the bar or press ◀▶to adjust Brightness of your camera from value 1 to 255.
Contrast
Drag the bar or press ◀▶to adjust Contrast of your camera from value 1 to 255.
Saturation
Drag the bar or press ◀▶to adjust Saturation of your camera from value 1 to 255.
Name
Set up name of each channel
Volume
Audio volume under LIVE mode and recording mode can be adjusted.
Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels.

11
1-5 ACCOUNT SETUP
The Account Setup menu is used to provide role-based permission independently setting for
each user (maximum of 4 users) to access DVR over network. The default admin account and
password is “admin”and “123456”
(The default password remains the same after firmware upgrade)
Item
Description
No.
Check to activate the user’s account.
Username
Set up username
Password
Set up password for each user. Password is 8-digits required and can
be mixed by letters and numbers with case-sensitive. Letters can be
mixed with capitals or lowercases.
Permissions
Set up Permissions for each user
Change Admin
Password
Change administrator’s password
Picture
Change user’s picture
1-5.1 Permission Setup
The Account Setup is set to provide individual user (maximum of 4 users) role-based
permissions, including access to Setup menu, Network operation, PTZ function, Playback,
Utility, Backup, Password expiry date and Mask on specific channels while playing back.

12
1-5.2 User Picture Setup
User can select picture wished to be changed to from hard drive.
1-6 NETWORKING SETUP
Item
Description
Connect type
Setup mode for network connection: (ADSL、DHCP、LAN、3G).
HTTP Setup
Enter to set up HTTP
DDNS Setup
Enter to set up DDNS
Mail Setup
Enter to set up mail
3G Setup
Enter to set up 3G network

13
1-6.1 NETWORKING SETUP
There are three ways to connect to the network as followed.
1-6.1.1 DHCP
When DHCP is selected, IP address will be assigned by DHCP server automatically.
1-6.1.2 LAN
Select LAN for network connection, the following information is required.
Item
Description
IP Address
Enter IP address provided by ISP
Subnet Mask
Enter IP address of Subnet Mask provided by ISP
Gateway
Enter IP address of Gate way provided by ISP
DNS
Enter DNS address provided by ISP.
(Note: The correct DNS address must be entered for DDNS function).

14
1-6.1.3 ADSL
Select ADSL for network connection, the following information is required.
Item
Description
User Name
Enter user name provided by ISP
Password
Enter password provided by ISP
1-6.1.4 3G
Select 3G for network connection, the following information is required.
Item
Description
Dial-up Number
Dial-up Number，Determined as the ISP
PIN
Enter SIM card password
APN
Enter ”internet”
Advance Setting
The advanced settings (Taiwan ISP outside)

15
Item
Description
Enable
Enable advance setting
User Name
Enter ISP username
Password
Enter ISP password
IP Address
Enter the ISP provides a fixed IP address。
(if the client uses the Internet only need to enter a fixed IP)
PS：This feature currently only supports the Huawei 3G card
1-6.2 HTTP Setup
Item
Description
Enable HTTP
Server
Check to enable HTTP server. Users can remotely access into the
DVR over the network if the HTTP function is activated.
Port
Enter a valid port value from 1 up to 65000. The default value is 80.
Auto
Assign each channel with its maxima accessible fps
No.
Chanel number
Quality
Set up record quality. There are below basic, basic, normal, high,
highest
FPS
Set up record FPS

16
1-6.3 DDNS Setup
Item
Description
Enable DDNS
Enable/disable DDNS function.
DDNS Server
Enter the registered SMTP Server:
ez-dns＊、I-DVR.NET＊、DYNDNS.ORG、NO-IP.ORG、3322.ORG
Host Name
Enter the completed registered SMTP Server.
(Including username + Server)
If the user name is h.264 and you choose i-dvr as your server,
you should enter: h.264.i-dvr.net
User Name
Enter user name.
Password
Enter password.
＊For more detailed I-DVR.NET,ez-dns operation instruction,please refer to appendix

17
1-6.4 Mail Setup
When event occurs (VLOSS, MOTION), email will be sent to the receiver account automatically.
Item
Description
Enable E-mail Notification
Check the box to enable/disable E-mal Notification function.
SMTP Server
Enter to set up SMTP Server name.
(Varies according to the user)
User Name
Enter to set up User Name.
Password
Enter to set up Password.
Sender E-mail
Enter to set up e-mail address of receivers.
Trigger Event
Enter to select events to send out E-mail notifications when below
circumstances happen: Motion, Sensor and Vloss (Video Loss).
Receiver E-mail
Enter to set up e-mail addresses for up to 10 receivers individually.

18
1-7 PTZ & RS485 SETUP
The DVR allows users to control PTZ functions of your camera. To enable PTZ function, the 485
cable should be connected to the RS-485 port of DVR.
Item
Description
Enable PTZ
Click the box to Enable/Disable PTZ function for each channel.
Protocol
Set up the protocol of PTZ cam. The supported protocol are
PELCO-P, PELCO-D, KND, LI-LIN, SAMSUNG, LG, AVTECH.
PTZ ID
Click or press ◀▶to set up PTZ ID. The valid ID value is from 1
to 64.
Baud Rate
Select Baud Rate for PTZ from 2400, 4800, 9600,19200
RS-485 ID
Select RS-485 ID from 1 to 64
RS-485 Baud Rate
Select RS-485 Baud Rate from 2400. 4800, 9600,19200
Keyboard
Select Keyboard.
Note：4CH DVR will display 4 channels. 8CH DVR will display 8 channels.

19
1-8 SYSTEM SETUP
Item
Description
DVR Name
The name of DVR will be shown when users login from remote access.
DVR Location
The location of DVR will be shown when users login from remote access
Language
Click or press ▼to select OSD language.
Remote ID
Default ID is 0. DVR is controlled by standard remote control,
Display Setup
Enter to set up Display
Date/Time Setup
Enter to set up Date/Time
Device Setup
Enter to set up Buzzer & Relay
Spot Setup
Enter to set up Spot
1-8.1 DISPLAY SETUP

20
Item
Description
Auto-Seq Interval
Set up duration time in seconds for the interval between channels
under Auto-Seq mode.
Show OSD
Turn On / Off OSD display
Show DVR Status
Turn On / Off DVR illustration and record status display
Show Date/Time
Turn On / Off date and time display
Show Channel Name
Turn On / Off channel name display
Border Color
Set up the color of border in LIVE , PLAYBACK mode.（Red,
Green, Blue）
1-8.2 DATE/TIME SETUP
Item
Description
Hour Format
12HOURS/ 24HOURS
Date Format
MM-DD-YY/DD-MM-YY/YY-MM-DD
Date/Time Position
Choose the position of Time and Date display
Change Date & Time
Setup time and date of DVR
Time Zone Setup
Set up GMT and Daylight Saving Time.
Internet Time Setup
Setup automatic synchronization with internet server