Securitytronix ST-PTZMINI-KB User manual

v1.0 6/21/11
1
USER MANUAL
ST-PTZMINI-KB
PTZ Keyboard Controller

v1.0 6/21/11
2
TABLE OF CONTENTS
PACKAGE'CONTENTS....................................................................................................3!
PRODUCT'DESCRIPTION ...............................................................................................3!
SPECIFICATIONS...........................................................................................................3!
INSTALLATION'AND'OPERATION ..................................................................................4!
1.!UNPACKING+and+HANDLING ....................................................................................................................... 4!
2.!MECHANICAL+INSPECTION.......................................................................................................................... 4!
3.!SPECIAL+ATTENTION .................................................................................................................................... 4!
4.!WIRING+CONNECTIONS ................................................................................................................................ 4!
5.!KEYBOARD+OPERATION .............................................................................................................................. 6!
KEYBOARD+OPERATION: ................................................................................................................................................. 7!
LCD!Screen!
Joystick!
Camera!Address!
PTZ!Camera!Lens!Control!
Setting!Preset!Scan,!Pattern,!Cruise!Functions!
Call!Camera!Main!Menu!
Matrix!Control!
Change!Monitor!
KEYBOARD+MENU+CONTROL: ........................................................................................................................................ 9!
Parameter!Setup!
Joystick!Calibration!
Camera!Setup!
Camera!Scan!Setup!
Camera!Pattern!Setup!
Camera!Tour!Setup!
Protocol!Setup!
Pelco!Matrix!Model!Setup!
6.!TROUBLESHOOTING+TIPS ........................................................................................................................ 15!
APPENDIX'1:'KEYBOARD'SHORTCUTS.........................................................................16!
APPENDIX'2:'MENU'TREE ...........................................................................................18!

v1.0 6/21/11
3
PACKAGE CONTENTS
This package contains:
One ST-PTZMINI-KB keyboard controller
One connection block
One 12VDC 2A power supply
One user manual
PRODUCT DESCRIPTION
The ST-PTZMINI-KB is a professional grade pan, tilt, zoom (PTZ) controller for up to 31
PTZ-enabled CCTV cameras and other devices. The unit uses RS-485 communications, includes
an LCD display and a 3-axis joystick.
Important Note
PTZ controllers are designed to perform a wide variety of PTZ camera control functions.
However, the utility of any PTZ controller is highly dependant upon the particular PTZ
camera to be controlled as each camera has not only its own functions but specific
methods of how those native functions are accessed and managed. Further, a particular
PTZ controller’s terminology may differ from that used by a particular PTZ camera.
Therefore, it will be necessary for the installer and/or user to consult BOTH the PTZ
controller and PTZ camera’s user manuals to ensure proper set-up, configuration and
application.
SPECIFICATIONS
ST-PTZMINI-KB
Specifications (Typical)
1. Communications Protocol
RS-485
2. Baud Rate
2400, 4800, 9600, and 19200 Bits/S
3. Transmitting Distance
3900 feet using 24AWG twisted pair cable
4. Operating Temperature
32°F -122°F
5. Relative Humidity
<90%
6. Power Supply
12VDC 2A
7. Dimensions
6.6”x5.4”x4.1”
8. Weight
14 oz.

v1.0 6/21/11
4
INSTALLATION AND OPERATION
1. UNPACKING'and'HANDLING'
Each unit is shipped assembled and factory tested.
Ensure that all accessories are removed from the container before discarding packing material
2. MECHANICAL'INSPECTION'
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be
damaged or defective please contact your distributor or Securitytronix at 1-610-429-1511 for
assistance.
3. SPECIAL'ATTENTION'
a. The installer must comply with electrical safety standards. There must be sufficient
space between the ST-PTZMINI-KB’s communication and power lines and camera’s
and DVR’s power supplies and video linesand any high voltage equipment and/or
cables.
b. Do not open up or dismantle the ST-PTZMINI-KB’s case. There are no serviceable
parts inside the unit.
c. Do not install ST-PTZMINI-KB in an environment where the temperature is below
32ºF or above 122°F.
d. Do not install the ST-PTZMINI-KB in a damp environment.
e. Only use a dry cloth to clean the unit. If there is dirt that is difficult to remove wipe
gently with a mild detergent. Never use strong or abrasive detergents.
f. A minimum 12VDC 2A power supply must be used. AC power cannot be applied.
Using an AC or other incorrect power supply will damage the unit.
g. Only qualified installers are allowed to install and test the ST-PTZMINI-KB.
h. As the ST-PTZMINI-KB is a sensitive device any shock or collision to the unit or
shaking of the unit will cause damage and void the warranty.
4. WIRING'CONNECTIONS'
a. The ST-PTZMINI-KB has an RS485 interface and an infrared interface for connection
to PTZ cameras or other peripheral devices (e.g., DVRs). The infrared interface is not
supported at this time.
Power/RS485
IR emitter

v1.0 6/21/11
5
The ST-PTZMINI-KB’s RS485 interface and power connection share a common
cable connected directly to the unit as depicted below. A terminal block for wiring
UTP (unshielded twisted pair) cable between the PTZ camera or other device and
the controller is included.
b. Connect the 12VDC 2A power supply to the ST-PTZMINI-KB’s female power
connector.
c. Using UTP cable connect the ST-PTZMINI-KB’s RS485 port to the PTZ camera’s
RS485 port. Using the terminal block be sure the polarities are correct and consistent
with the camera. Always consult the camera’s manual regarding PTZ controller
connections.
d. Connect power supply’s AC plug to a suitable AC power outlet. When power is applied
the ST-PTZMINI-KB will automatically display the baud rate and keyboard protocol on
the LCD screen. Note: When the controller is initializing the joystick should be in the
“nil” (0 or neutral) position.
e. It is also possible for the ST-PTZMINI-KB to control multiple PTZ cameras using a
matrix switch in lieu of a DVR per the diagram below. The PTZ controller and cameras
are connected in parallel to the matrix’s RS485 buss. Be sure to assign each camera
aunique address and set the cameras’ and controller’s communications at 9600bps.
RS485 A+ B-
Camera A+ B-

v1.0 6/21/11
6
f. Note: If using more than one PTZ controller each controller must have a unique ID.
Further, no more than 4 ST-PTZMINI-KBs can be used in one system.
5. KEYBOARD'OPERATION'
Controller Matrix PTZ Camera 1 PTZ Camera 2
LCD Screen
Lens Control
3D Joystick
Function Keys
Number Keys
Keypad Cover

v1.0 6/21/11
7
KEYBOARD'OPERATION:''
LCD'Screen'
'Joystick'
Camera'Address'
PTZ'Camera'Lens'Control'
Setting'Preset'Scan,'Pattern,'Cruise'Functions'
Call'Camera'Main'Menu'
Matrix'Control'
Change'Monitor'
''
LCD Screen: The LCD displays key information including camera address or ID, monitor
address or ID, protocol, baud rate and joystick position. When an operation is initiated the
LCD will be lit and remain on for 10 seconds after the operation is completed.
Joystick: The joystick controls both camera positioning and camera menu selection and
setup.
Camera Positioning: The camera will follow the joystick’s direction. The joystick
and camera’s position will be displayed on the LCD as 
Camera Menu Setup: The joystick is used to selection menu items as follows: 
for the upper menu item, for the next menu item, for a sub menu or save and
for cancel, return to submenu or exit.
Camera Address: To choose the camera to operate use N +CAM where Nis the camera
address (e.g., 1). Enter camera address then press CAM.
PTZ Camera Lens Control: Use the ST-PTZMINI-KB to control the camera’s Zoom,
Focus and Iris lens features.
Zoom: Control the zoom by rotating the joystick –clockwise to zoom far, counter
clockwise to zoon wide.
Focus: Press the FAR key to focus far objects. Press the NEAR key to focus near
objects. Normally Zoom and Focus will be adjusted automatically by the camera.
Iris: Press the OPEN key to open the iris. Press the CLOSE key to close the Iris.
Pressing these keys will manually adjust the iris. Note: Many cameras do not
support manual iris control.
Setting Camera Presets, Scan, Pattern and Cruise Functions:
Preset:
oTo create a preset move the camera to the desired point, press the SET
key, the Nkey (where Nis the preset number) and the PRE key (SET +N
+PRE).
oTo adjust the preset press the N key and the PRE key (N +PRE).
Scan:
oTo set the left border, press the SET key, 1key and SCAN key (SET + 1
+ SCAN).
oTo set the right border, press the SET key, 2key and SCAN key (SET + 2
+ SCAN).
oStart: To start the Left –Right scan press the 1key and SCAN key (1+
SCAN).

v1.0 6/21/11
8
oEnter the camera’s menu to change the scan speed.
Pattern:
oTo create a pattern press the SET key, the Nkey (where N is the number
to designate a pattern scan), the PATTERN key then direct the camera
along the path for the pattern the press the SET key, the 0 key then the
PATTERN key (SET + N+ PATTERN + camera path + SET + 0+
PATTERN). Note: up to 4 patterns can be created and stored (N will be
designated 1, 2, 3, or 4).
oTo start a pattern scan, input the pattern number 1, 2, 3 or 4 then press
the PATTERN key to commence scanning. (enter 1, 2, 3, or 4,+
PATTERN).
Tour:
oTo start a cruise press the Nkey, then the TOUR key. Nrepresents the
desired tour number and TOUR will start the cruise (N+ TOUR).
oIf only one cruise has been created then simply press the TOUR key.
Call The Camera’s Main Menu: Press 9+ 5 + PRESET. The camera’s menu will be
displayed on the monitor.
Matrix Control: A matrix can support a specific number of PTZ cameras. The
ST-PTZMINI-KB can support up to 16 PTZ cameras in a matrix. All camera information
such as address, data, and time will be displayed when switching from one camera to
another. Note: the user should refer to the matrix switch’s manual regarding the matrix’s
specific features, functions and limitations.
Switch Camera Order: Press the PREV key to switch back to the previous
camera. Pressing and holding the PREV key for 2 seconds will allow switching
backwards through all cameras. Press the STOP key to stop switching. Press the
NEXT key to advance to the next camera. Pressing and holding the NEXT key for
2 seconds will allow switching forwards through all cameras. Use the STOP key to
stop the switching.
Call Matrix Main Menu: To call the matrix switch menu press the SHIFT and SET
keys (SHIFT + SET). The menu will be displayed on the monitor.
Confirm Matrix Programming: Refer to the matrix switch’s manual regarding
how to program the matrix. Press the ENTER key to confirm a program setting.
Change Monitor: To change image to a different monitor press the Nkey (where Nis the
monitor ID) and the MON key (N+ MON).

v1.0 6/21/11
9
KEYBOARD'MENU'CONTROL:''
Parameter'Setup'
Joystick'Calibration'
Camera'Setup''
Camera'Scan'Setup''
Camera'Pattern'Setup''
Camera'Tour'Setup'
Protocol'Setup'
Pelco'Matrix'Model'Setup'
By pressing and holding the MENU key for 2 seconds the main menu screen (as above)
will appear. The user must enter the main menu and either use the menu item number or
joystick to select the desired menu item. Once done, move the joystick right or press
ENTER to enter that menu.
To move to a previous menu item press the PREV key or move the joystick left.
To save a menu setting selection press the ENTER key. The LCD screen will then display
“Success”.
Keyboard Parameter Settings: Keyboard Camera ID Setup; Keyboard Baud Rate
Setup; Keyboard Information Display.
Keyboard Camera ID Setup:
oPress the MENU key and select 1. Keyboard Setup from the main menu.
The Keyboard Setup Menu screen similar to the one below will appear.
Press the 1key for Set KB ID.Press 1again and the LCD screen will display:
oPress 1to select the keyboard ID setting. Use the numeric keys to select
the ID from 1 to 64 (if the selected ID is greater than 64 “Error” will be
displayed). Then press the ENTER key to save. Upon doing so “Success”
will appear on the screen.
oTo move to the previous menu press the PREV key or move the joystick
to the left.
oNOTE: The keyboard ID default is 1.
1. Keyboard Setup
2. Dome Setup
3. Protocol Select
4. Exit Menu
1. Set KB ID (1-64):
2. Set Baudrate: 2400bps
3. Joy Calibrate
4. About Keyboard
1. Set KB ID (1-64):

v1.0 6/21/11
10
Keyboard Baud Rate Setting:
oPress the MENU key and select 1. Keyboard Setup from the main menu.
The Keyboard Setup Menu screen similar to the one below will appear.
oPress the 2 key and the select baud rate setting screen similar to the one
below will be displayed.
oMove the joystick right or up/down to select the desired baud rate then
press ENTER to save. Upon doing so “Success” will appear on the
screen.
oTo move to the previous menu press the PREV key or move the joystick
to the left.
oNOTE: If the PTZ controller is connected to a matrix switch the baud rate
must be 9600bps. If several controllers are to be used together the baud
rate must be 9600bps or 19200bps.
About Keyboard:
oPress the MENU key and select 1. Keyboard Setup from the main menu.
The Keyboard Setup Menu screen similar to the one below will appear.
oPress the 4key to display keyboard information.
Joystick Calibration: With the joystick in the center position press the MENU key and the
1 key to select keyboard setup. Then select 3. Joy Calibrate from the Keyboard Setup
Menu. Note: the joystick must remain in the center (neutral) position when calibrating.
1. Set KB ID (1-64):
2. Set Baudrate: 2400bps
3. Joy Calibrate
4. About Keyboard
1. Set KB ID (1-64):
2. Set Baudrate: 2400bps
3. Joy Calibrate
4. About Keyboard
2. Set Baud Rate: 2400bps