SecurView OEM-6400.FT User manual
INSTALLATION INSTRUCTIONS:
The OEM-6400.FT is a special designed OEM camera with a custom mounting style that allows
it to be mounted easily to the vehicle. It is designed to take the place of the license plate
illumination lamps on the Ford Transit Van 2010-2012 vehicles with minimal installation time
and with no special tools required for the job. Once installed, the camera looks completely
factory and is easy to keep out of sight.
FEATURES:
•Replaces the license plate illumination lamp when mounted
•170°ultra wide-angle
•Easily mounts to vehicle with minimal installation time
•Parking assist lines to help the driver accurately judge distance behind the vehicle
•Constructed of high-grade plastic
•Reverse image
•The OEM cam easily connects with other SecurView products such as any of the LCD
monitors. It can also be integrated with your existing OEM or aftermarket LCD/TFT
displays.
•The Securview™ OEM-6400.FT is designed specifically for the Ford Transit Van vehicle
and may not work well on other vehicles. Please check the vehicle before installing to
make sure the camera can be properly placed
OEM-6400.FT
Wide-
Angle OEM
Camera
INSTALLATION
MOUNTING:
1. The OEM-6400.FT is design to be mounted on the License Plate bezel of a Ford Transit Van
vehicle. The particular mounting style of this camera will allow it to only be used on the
license plate lamp of this particular vehicle.
2. Unclip and remove the factory license plate illumination lamp using a screw driver or panel
removing tool (STEP 1). To do this, you may need to remove the interior panel of rear cargo
door. Be cautious not to scratch the paint on the body surface.
3. The bulb housing can be separated from the fixture once the assembly is removed. (STEP 1)
4. Route the wire harness through the fixture (STEP 2)and into the door through the license
plate limp mounting location. The wire harness can then be routed into the van through the
factory door boot.
5. Snap the OEM-6400.FT camera in place on the light fixture. Make sure it is secured tightly
once it is snapped into place. The factory license plate bulb should now be housed inside the
OEM-6400 camera. Snap the camera and fixture into place on the door (STEP 2).
NOTE: The interior panels of the rear cargo door will need to be removed in order to route the
camera cable into the car. This will also make it easier to remove the license plate lamp.
STEP 1 STEP 2
Remove the license plate lamp from the rear door
and remove the lamp housing from the fixture Replace the lamp housing with the OEM-6400.FT
camera and snap it into place on the lamp fixture.
Snap the camera/lamp assembly into place
CAMERA:
1. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is designed to work well in day time or night time conditions.
3. The camera is completely electronic. There are NO manual adjustments for focus, etc.
WIRING:
1. Carefully route the wiring harness of the camera into the van using the pre-existing factory door
boot. Be careful not to accidentally break any wires or damage the rubber door boot when routing
the camera wiring harness.
2. Choose a convenient place to run the camera cable up the left or right side of the vehicle. As a
rule of thumb, try to avoid main factory harness looms that may contain high levels or RF noise or
interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You may
also connect power inside the vehicle under the dash or in the trunk. The Red power wire goes to
Reverse Light +12V, and the Black wire to Ground.
4. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input.
•The pair of Green wires coming out of the wire harness is for the Parking Guidelines feature.
If you leave the two wires disconnected, the parking lines are activated. If you connect the two
wires together, the parking lines will be turned off.
MONITOR
YELLOW RCA
Connect to +12V
Reverse Light
Ground
RED
WIRE
BLACK
WIRE
YELLOW RCA
Connect to
Monitor
POWER PLUG
GREEN WIRE
Parking Guideline Option
TECH SUPPORT: (800) 998-6880
DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the Securview™ be held liable for
consequential or incidental damages sustained in connection with the use of the Securview™ Rear
Vision System. The Securview™ is designed as a safety enhancement device and is in no way intended
as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. For the best fit, modification of the vehicle license may or may not be
necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or
Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of
the Securview™ assumes no liability or responsibility whatsoever with regards modifications of the
license plate.
www.crimestopper.com
email@crimestopper.com
Phone (800) 998-6880
FAX (805) 581-9500
© 2012 Crimestopper Security Products
2-22-2012
SPECIFICATIONS:
1/4 Inch Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (In.): 1¼"(L) × 2⅜"(W) × 1⅜"(D) Supply Voltage: +12VDC
Weight: 3 Oz. Power Consumption: 70mA
Pixels: 648 (H) x 488 (V) Shutter: 1/50 s – 1/100000s
Resolution: > 250,000 pixels White Balance: Automatic
420 TV lines Gamma Correction: 0.45
Minimum Illumination: 0.5 LUX / F 1.2 S/N Ratio: More than 48dB
Lens Type: Wide Angle Operating Temp: -22° to 176° F (-30° to 80° C)
Horizontal Angle: 170° Gain Control: Automatic
Vertical Angle: 90°
Table of contents
Other SecurView Dashcam manuals
