Savant PAV-VIM1CP2 Series User manual

PAV-VIM1CP2-xx Quick Reference Guide | 009-2033-01
Copyright 2022 Savant Systems, Inc | 220823
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Box Contents
Networking Guidelines
To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: IP video device requirements and how to manage IP addresses
are available on the Savant Device Netwoking Guidelines on the
Savant Customer Community.
Front Panel
APower LED O - Device is o. No power applied.
Blue - Main board is powered
BVideo LED O - No video signal detected.
Blue - Video signal detected.
CLinkTX LED
O - No valid connection
Blue - Valid link
Blinking - Sending Ethernet Data
DLinkRX LED
O -No valid connection
Blue - Valid link
Blinking - Receiving Ethernet
EStatus
Blue - Reset button is pressed when the
device is powered on
Blinking - Reset button has been released or
the device was powered on without holding
the reset button
FP1 Reserved for future use.
GReset
Hold down this button with a pointed
stylus for 20 seconds while powering up
the device to restore the device to factory
default settings
Specifications
Environmental
Temperature 30° to 105° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Device 0.98 in
(2.48cm)
6.3 in
(16cm)
5.72 in
(14.52cm)
1.35 lb
(0.61 kg)
Shipping 3.63 in
(9.22 cm)
15.5 in
(39.37 cm)
8.5 in
(21.59 cm)
2.65 lb
(1.20 kg)
Power
Power over
Ethernet (PoE+) IEEE 802.3at
Input Power 12V 2A DC
Power
Consumption 16 W
Audio
Supported
Formats
Pass-though of all HDMI 2.0 audio formats are
supported.
Power Video LinkTx LinkRx Status P1 Reset
BCDEFG
A
Network Requirements
For more information, see the Savant Device Networking Guidelines
on the Savant Customer Community.
(1) Single Video IP Transmitter (PAV-VIM1CP2-xx)
(1) Installation kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) International Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Information and Regulatory Statement (009-1950-xx)
1 = at 24 Hz
2 = at 25 Hz
3 = at 30 Hz
4 = at 50 Hz 5 = at 60 Hz
Video
HDR Supported
Supported
Formats
640x4805
720x4806
720x5764
800x6005
1024x7685
1280x7204
1280x7205
1280x10245
1920x10801
1920x10803
1920x10804
1920x10805
1920x12005
3840x21601
3840x21602
3840x21603
3840x21604
3840x21605
4096x21603
4096x21605
Required Components
– Savant IP Video Receiver
– Savant System Host
– Savant qualified 10G Managed Network Switch
– Savant User Interface
– Savant Development Environment (SDE)
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant IP Video Deployment Guide (009-1977-xx)
– Savant IP Video Network Configuration Guide (009-1552-xx)
– Savant IP Audio Deployment Guide (009-1571-xx)
– Savant Device Networking Guidelines
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Supported Releases
Software
Release da Vinci 9.4 and higher
Supported Audio and Video Formats
Savant® IP Video Single Input Transmitter 4K UHD with Control (PAV-VIM1CP2)
Quick Reference Guide

PAV-VIM1CP2-xx Quick Reference Guide | 009-2033-01
Copyright 2022 Savant Systems, Inc | 220823
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
RJ-45 10G Ethernet connection.
Transport Distance
Cat6 100ft (30m)
Cat6a 300ft (100m)
Cat7 300ft (100m)
10 GbE
Wiring and Connections
IR connection are made using 3.5 mm IR
Emitter supplied with the device.
IR Wiring
Serial control connection are made
using a 3-pin Control Connector
supplied with the device. The wire slips
into the hole and locks with a screw
located at the top of the connector.
RS-232 Wiring
Rear Panel
Item Description
DC 12V 12V 2A DC
HDMI In
19-Pin Type A HDMI female digital audio/
video input with locking connector.
Supports HDMI 2.0a
HDMI 2.0 complaint cable required for 4K
content.
RS232
3-pin Control Connector. Transmits and
receives serial data to and from serial
controllable devices. For pin-out
information, refer to the RS-232 Wiring
section.
10GbE
RJ-45 port.
10G connection to the IP Video 10G switch.
Supports Power over Ethernet (PoE+ IEEE
802.3at standard).
Link LED
Solid Green - Link is established with
2.5/5GBase-T mode.
Solid Amber - Link is established with
10GBase-T mode.
O – No link established.
Link Activity
LED
Amber Blinking - Indicates data activity.
O – No Activity
IR Out
3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to
devices with an IR input or IR receiver
LAN
1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto
the Ethernet network by sharing the 10G
network link. 8-pin RJ-45 female connection.
IMPORTANT!: Do not connect this port to a
network switch.
Link LED Solid Green - Link is established.
O – No link established
Link Activity
LED
Amber Blinking - Indicates data activity.
Solid Amber - Connected but there is no
data activity.
O – No Activity.
Audio
3.5 mm (1/8 in) Analog Audio connection.
For use information refer to the Savant IP
Video Deployment Guide on the Savant
Customer Community.
A
B
C
D
E
F
G
H
I
J
K
Installation
To install the PAV-VIM1CP2 use the mounting screws to attach the
included mounting brackets. Please follow the steps below.
1. Align the bracket using the top holes.
NOTE: This will leave an air gap behind the device.
2. Use mounting screws to attaching the bracket.
If the device is going to be mounted vertically Savant recommends
aligning the device with the rear of the device facing down. This will
allow the best heat dissipation.
Rear Panel
Rack Installation
The PAV-VIM1CP2 can be rack mounted using the RCK-PAVVM8.
(rack purchased separately)
RS232
TX RX G
HDMI In 10 GbE (PoE+)DC 12V IR Out LAN Audio
A B C D
E F
G H
I J
K
3
2
1
Rx
Tx
G
PIN 1
PIN 2
PIN 3
Receive
Transmit
Ground