SeeEyes SC-IPU601 User manual
Release Version 1.0
High Power IP Over UTP Transmission Solution
SC-IPU601(SC-IPU601T, SC-IPU601R)
User Manual
SC-IPU601R
(1CH Receiver)
SC-IPU601T
(1CH Transmitter)
Release Version 1.0
1
Precaution and Safety Guidelines
The content of this guideline is to protect the safety of users and prevent property damage.
Be sure to read this user’s manual thoroughly and use the device correctly.
Warning (If you do not keep any of the below guidelines, you may get seriously injured or
cause somebody’s death.)
■Be sure to install the product after unplugging power cord. Also, do not use several
power plugs at the same time.
- It may cause abnormal heat, fire and electric shock.
■Do not leave the device at any place that water falls or splashes. Also, do not put anything
full of water such as a flower vase on the device.
- It may cause malfunction or fire if liquid goes into the device.
■Do not bend the power cord by excessive force. Make sure the power cord is not crushed by
heavy things.
- It may cause fire.
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble,
repair or modify it.
- By abnormal working, it may cause fire, electric shock and personal injury.
■Do not install this product in places with high humidity, dust, or soot.
- It may cause electric shock and fire.
■Do not tug at the power cord section or unplug the power plug with wet hands. If the power
cord is loose, do not plug in.
- There may be a risk of fire and electric shock.
■Always keep the location of the appliance clean during or after installation to prevent dust.
Especially when cleaning the device, wipe it with dry towel and do not use water, thinner or
organic solvent.
- It may damage the case of this device, and cause malfunction or electric shock.
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or
tools away from places where people come and go.
- It may cause fire.
■Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power
extension cables, old power cords and a lack of safety earth. Consult your place of purchase or
professional if problems arise.
- It may cause fire and electric shock.
■Concerning the input voltage for operating this device, a voltage range must be within 10%
of rated voltage, and the power outlet must be grounded. Also, do not use a heat source such
as a hair dryer, iron and refrigerator to the same power unit.
- It may cause abnormal heat, fire and electric shock.
Release Version 1.0
2
Caution (If you do not keep any of the below guidelines, you may get injured or suffer
property loss.)
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
■Install in well ventilated place, and avoid direct sunlight or heat appliance.
■Be sure to plug the power cord with grounded outlet.
- There is a risk of electrical shock and personal injury.
■Do not use this device in close proximity to a device that produces strong waves such as
radio set(TRANCEIVER, Walkie-talkie, etc.) or repeater. It may affect the video signal, or cause
disorders such as noise or crack on the screen.
■Disconnect the power plug with care during thunder and lightning.
■When connecting cables, install as “U” shape in order to prevent rainwater/dew/fog from
getting into the product.
■Refer to the user’s manual for problems or questions besides the above. Contact our service
center if you need assistance from a professional technician.
■UTP(Unshielded Twisted Pair) Cable is for indoor use only. For outdoor use, it is
recommended to use STP(Shield Twisted Pair) Cable which is covered with shield.
- Use standard CAT.5e or higher UTP cable.
■Since this product has a PoE (Power Over Ethernet.) function, it may cause malfunction to the
connected device which doesn’t support PoE function. Make sure to read the user's manual
carefully before using this product.
■Make sure to separate general communication network (internet / in-house use, etc.) from
CCTV network.
- It may cause malfunction.
■Be careful not to change the network cable configuration.
- Refer to the cable wiring way below.
Network Cable Diagram
TIA / EIA 568B Type
Pin No.
Color
Function
1
White
Orange
TX+
2
Orange
TX-
3
White
Green
RX+
4
Blue
PWR+
5
White
Blue
PWR+
6
Green
RX-
7
White
Brown
PWR-
8
Brown
PWR-
Release Version 1.0
3
1. Introduction
1-1. Overview
The 1-channel High Power IP Over UTP Transmission Solution consists of the transmitter(SC-
IPU601T) and the receiver(SC-IPU601R). Among SeeEyes’ IP transmission device series, this product
was developed as a High Power supporting product of SC-IPC07PU, and the PoE output of the
transmitter (SC-IPU601T) supports up to 70Watt, enabling high-performance and high-capacity IP
cameras over long distances with PoE technology. PoE technology enables power supply to the
transmitter and camera, so no separate power supply is required.
Existing analog UTP cameras can be replaced with IP cameras, and the existing UTP cable (CAT.5e/6)
can be used, which shortens the construction period and reduces construction costs.
1-2. Features
•IEEE 802.3af/at/bt support
•Possible to supply power for IP camera (PoE Type B supported / max. 70W)
•Transmission bandwidth: up to 100Mbps
•Ethernet data can be transmitted up to 800m via UTP cable (CAT.5e/6) (10Mbps)
•Auto MDI/MDIX function support
•Safe power transmission with automatic line diagnosis function
•Camera-side transmitter PoE function ON/OFF setting switch
•Surge protection circuit
2. Components
SC-IPU601T
SC-IPU601R
Power code
DC adapter
User manual
※Accessories included in the product are subject to change.
Release Version 1.0
4
3. Product Parts and Functions
3-1. SC-IPU601T(Transmitter)
①CAMERA PoE: Switch to set power supply to PoE IP camera.
※In case of connecting PoE IP camera, set CAMERA PoE switch as ON.
※The factory setting for the PoE switch is ON.
※In case of connecting non-PoE IP camera, set CAMERA PoE switch as OFF.
②LED Indicator
Name
Color
Status
PWR
Red
On: Power input
Off: No power input
ETH
Green
Blinking: Ethernet connected
Off: Ethernet Not connected
LINK
Green
On: Connected to Receiver
Off: Not connected to Receiver
PoE
Red
ON: PoE Input to IP camera
Off: No Poe input to IP camera
Blinking: IP camera side power supply error (short circuit,
disconnection, overcurrent)
※When turning the product on, the LED turns on sequentially first and the product is operated.
③RECEIVER SIDE: Port to connect Receiver and output video.
④CAMERA SIDE: Port to connect IP camera.
①
③
④
②
Release Version 1.0
5
3-2. SC-IPU601R(Receiver)
①NVR SIDE: Port to connect NVR or PoE Hub.
②DC 48-56V IN: Port to input DC adapter (48V or 56V) power.
③TRANSMITTER SIDE: Port to connect Transmitter and input video.
④LED Indicator
Name
Color
Status
PWR
Red
On: Power input
Off: No power input
ETH
Green
Blinking: Ethernet connected
Off: Ethernet Not connected
LINK
Green
On: Connected to Transmitter
Off: Not connected to Transmitter
PoE
Red
On: PoE output to Transmitter
Blinking: IP camera side power supply error (short circuit,
disconnection, overcurrent)
⑤Bandwidth Select Switch: 100Mbps, 10Mbps setting
※10M: Transmit by 10Mbps (10Mbps over CAT.5e : 800m).
※100M: Transmit by 100Mbps (100Mbps over CAT.5e : 500m).
※When turning the product on, the LED turns on sequentially first and the product is operated.
④
④
①
③
②
⑤
④
Release Version 1.0
6
4. Connection Diagram
4-1. In case of connecting PoE IP Camera (TX’s PoE Switch ON)
5. Precautions for product installation
※Use a dedicated adapter individually for each product. It is not recommended to input power to
multiple products with one adapter.
※It is not recommended if the products are in contact with each other or tied together.
※When supplying PoE to the receiver, it is not recommended to connect the DC adapter.
※When installing the product with PoE supply, it is recommended to ground the camera after
checking the video.
※When an installing a surge protector, the distance between the camera and the transmitters is
recommended to be within 50m.
※Using a LAN cable extension gender (coupler) causes signal attenuation. The use of
multiple extension gender connections is not recommended.
< Installation Guide >
①Set SC-IPU601T’s CAMERA PoE switch to ON. (PoE LED On)
※In case of connecting non PoE camera, set transmitter’s CAMERA PoE switch to OFF.
②Connect the IP PoE CAMERA to the transmitter and connect the UTP cable to the terminal connected to
the SC-IPU601R (receiver).
③Connect UTP cable from Transmitter to Receiver. Connect Receiver to NVR or PoE Hub.
④Check the transmission distance and set the Bandwidth switch of Receiver to the corresponding
transmission bandwidth.
※10M: Transmit by 10Mbps (10Mbps over CAT.5e: 800m).
※100M: Transmit by 100Mbps (100Mbps over CAT.5e: 500m).
⑤Supply power by connecting DC Adapter (48V or 56V) to the DC Jack of the receiver. (Option)
⑥Check the camera’s video from the monitor connected to NVR.
※If connected properly, LINK LED on Tx and Rx is ON and ETH LED is blinking.
Release Version 1.0
7
6. Specifications
MODEL
SC-IPU601T
Power Input
PoE from SC-IPU601R
Power Output
Midspan PoE (Type B Only, PoE SW On/Off)
Transmission Bandwidth
10/100Mbps
Connection Port
RECEIVER SIDE
RJ-45 (TIA/EIA568B Type)
CAMERA SIDE
RJ-45 (TIA/EIA568B Type)
LED Indicator
PWR
RED LED
ETH
GREEN LED
LINK
GREEN LED
PoE
RED LED
CAMERA PoE SW
Slide switch: PoE On/Off selection
Operating Temperature / Humidity
-10℃~ 50℃/ 0 ~ 80%
Case Body / Weight
Aluminum / 96g
Dimensions
103(W) x 60(D) x 25(H) mm
MODEL
SC-IPU601R
Power Input
AC Adaptor(DC 48-56V) or PoE Hub (IEEE 802.3af/at/bt)
Power Output
PoE
Max. Transmission Distance
(CAT.5e)
100Mbps: 500m
10Mbps: 800m
Transmission Bandwidth
10/100Mbps
Connection
Port
TRANSMITTER SIDE
RJ-45 (TIA/EIA568B Type)
NVR SIDE
RJ-45 (TIA/EIA568B Type)
DC 48V-56V IN
DC-JACK
LED
Indicator
PWR
RED LED
ETH
GREEN LED
LINK
GREEN LED
PoE
RED LED
Bandwidth Select Switch
10M / 100M
Operating Temperature / Humidity
-10℃~ 50℃/ 0 ~ 80%
Case Body / Weight
Aluminum / 98g
Dimensions
103(W) x 60(D) x 25(H) mm
Release Version 1.0
8
7. Maximum supplyable power
Distance
CAT.5e
Bandwidth
DC 56V 2A
PoE(802.3bt,
DC 54V)
DC 48V 1A
50m(164ft)
100Mbps
70W
52W
41W
100m(328ft)
100Mbps
65W
49W
38W
200m(656ft)
100Mbps
55W
42W
31W
300m(984ft)
100Mbps
41W
34W
22.5W
400m(1312ft)
100Mbps
31W
25.5W
17.5W
500m(1640ft)
100Mbps
24.5W
20.5W
14W
600m(1968ft)
10Mbps
20.5W
17W
11.5W
700m(2296ft)
10Mbps
17.5W
15W
10W
800m(2624ft)
10Mbps
15.5W
13W
8.5W
※Depending on the power specifications of the camera, a difference of about 20 to 30% may occur
compared to the power supply value in the table, and the cable transmission distance may vary
depending on the specifications of the camera, NVR, cable etc.
※When using the PoE function of the transmitter, the transmission distance may vary depending on
the camera type.
In particular, for IP PTZ cameras and cameras with many IR LEDs that consume a lot of power, use
a dedicated camera power adapter. It is recommended that the cable distance between the camera
and the transmitter be less than 1 m.
※When inputting power to the receiver through a PoE hub, it is recommended that the network
cable distance be less than 1m.
※When transmitting over a cable distance of 500m, camera input voltage may be low and may
malfunction. Please, connect a DC 56V adapter to the receiver.
Release Version 1.0
9
8. Trouble Shooting
Symptom
Checking Method
No Power
<Transmitter>
•Check if PoE LED on Receiver and PWR LED on Transmitter is ON.
•Check the connection status of UTP cable.
<Receiver>
•Check if the PWR LED is working properly.
•Check the input status of power adapter or PoE Hub.
•Check if the exclusive adapter(56V) is used.
No Video
•Please check if LINK LED is ON and ETH LED is flashing.
•Check if the transmission distance is within the recommended
value or not.
•Check if the Network cable’s wire arrangement is correct.
•In case of using PoE function on Transmitter, check if the PoE LED
is On. If LED is Off, set the PoE switch as ON.
No PoE
•Check the PoE switch status on Transmitter.
•Check if PoE LED on Transmitter is ON.
•Check if the Network Cable arrangement is correct.
•Check if the IP CAMERA supports PoE function.
Unstable Network
•Check if the Network cable’s wire arrangement is correct.
•Check if there is Walkie-Talkie or any device which has strong
waves near the product.
•Check if the Network configuration is installed properly.
Unstable Video
•Check the connection status of UTP and Network cable.
•Check if the NVR is compatible with camera.
•Check the performance status of camera.
Release Version 1.0
10
9. Warranty Certificate
Product No.
Model No.
Date of Purchase
Place of Purchase
Purchaser
Name
Address &
Contact No.
Distributor
Name
Address &
Contact No.
Warranty Period
Two(2) years from the date of purchase
Any failure that occurs in the normal use for only two years after purchase will be
repaired free of charge.
Contact the phone number listed on the user’s manual for repair.
When reporting the failure, please inform the model name and condition of the
product accurately. It is convenient to know the name and department of the person
in charge.
Please check this user’s manual again before reporting the failure.
Product shapes and circuits are subject to change without notice to improve
performance.
Faults following will be treated as a charge:
✓Failure by user’s handling without care
✓Not connecting the rated power
✓Disassembled or repaired arbitrarily by user
✓Replacing consumables
✓Failure caused by natural disaster (lightning, fire, flood, tsunami, etc.)
This manual suits for next models
2
Table of contents
Other SeeEyes Microphone System manuals
